Fiat X1/9

Design and development

The X1/9 succeeded the 1969 Autobianchi A112 Bertone Runabout concept, with styling by Bertone under chief designer Marcello Gandini.

The Runabout was powered by the same engine as the Autobianchi A112.^[10] The Runabout featured a distinctive wedge shape and took many styling cues from contemporary power-boat design. Though the more extreme features of the Runabout such as the C pillar mounted headlights and the small wind-deflector windscreen were lost for the production car, many aesthetic features of the Autobianchi Runabout are readily identifiable on the X1/9. The long flat bonnet (hood) with central indentation, the large front overhang, the wedge shape with prominent C pillar roll-over hoop and the car-length indented plimsoll-line all made the successful transition to the X1/9, giving it a highly distinctive appearance.

Designed around the all-new Fiat SOHC engine and transmission from the front wheel drive Fiat 128, the X1/9 relocated the transverse drive train and suspension assembly from the front of the 128 to the rear of the passenger cabin, directly in front of the rear axle, giving a mid-engined layout. The engine was Designed by Aurelio Lampredi, famed Ferrari engine designer before he went to work for FIAT (the parent company, at that time). The layout located the fuel tank and spare wheel ahead of the engine, behind the driver and passenger seats respectively — optimizing the proportion of the car's weight within its wheelbase for more balanced handling and enabling cargo areas front and rear.^[11][12] Once developed for production, the two-seater featured sharp-edged styling with a wedge shape, retractable headlights, an integrated front spoiler and a removable hard top roof panel (targa top). The removable hardtop could be stored in the front boot; a second luggage compartment was provided at the rear of the car, accessible through a conventional boot lid.

Unlike Fiat's marketing nomenclature at the time which used a numerical system (e.g., 127, 128, 124, 131) denoting relative position in the model range, the X1/9 retained its prototype code as its marketing name. Fiat's prototype coding used X0 for engines, X1 for passenger vehicles and X2 for commercial vehicles. The X1/9 was thus the ninth passenger car developed using the nomenclature.

Production and model evolution

Originally slated for the November 1972 Turin Motor Show, the X1/9's launch was delayed until after the show to avoid upstaging the new Fiat 126 citycar. Press test drives were held at the end of November 1972, on the Sicilian Madonie roads home to the Targa Florio road race.^[13]

The car was intended to replace the 850 Spider, another Bertone design, not the more expensive 124 Sport spider whose production continued for much of the X1/9's life. The car's monocoque body was produced at the Bertone factory in Grugliasco (Turin)^[14] and then transported to the Fiat's Lingotto factory for final assembly. As mentioned before, the X1/9's type 128 AS 1,290 cc (79 cu in) single overhead cam inline-four engine was derived from the Fiat 128, specifically from the 128 Coupé 1300. Changes included a new cast aluminium oil sump,^[12] complementing the aluminium cylinder head. With a twin-choke Weber 32 DMTR carburettor and an 8.9:1 compression ratio, the engine produced 75 DIN-rated metric horsepower (55 kW; 74 hp) at 6,000 rpm and 97 DIN-rated newton metres (72 lb⋅ft) of torque at 3,400 rpm.^[6][12] The all-synchronized 4-speed transmission was also carried over from the 128, though with a taller fourth gear ratio to exploit the sports car's better aerodynamics. As a consequence the X1/9 had a top speed of over 170 km/h (106 mph), 10 km/h higher than the similarly engined but 65 kg lighter 128 Coupé 1300.^[12] As standard the X1/9 came with 4.5J×13-inch stamped steel wheels fitted with 145 HR 13 tyres, while cast alloy wheels were an extra-cost option.^[14] Suspensions were all-independent, of the MacPherson type on both axles. The split circuit brake system used equally sized 227 mm discs all around.^[14] Steering was rack and pinion. The interior, upholstered in leatherette, featured two bucket seats with integrated headrests and a four-spoke steering wheel (resembling the one fitted to the Lamborghini Marzal).

The original 1.3-litre, 4-speed X1/9 can be immediately distinguished from the later 1.5-litre, 5-speed model by its wrap-around steel split bumpers with rubber blocks, and the shallower engine compartment lid.

Fiat began marketing a right-hand drive variant in 1976. Before official right-hand drive X1/9s were manufactured by Fiat in 1976, Radbourne Racing were converting left-hand drive X1/9s to a right-hand drive configuration for sale in the UK market. None of these early conversions are believed to remain in existence.

In 1982, shortly after the introduction of the 1500 model, complete production was assumed by Bertone with models subsequently badged as the "Bertone" X1/9. Bertone models featured revised footwells redesigned to enhance legroom and sitting comfort for persons taller than the original design's target.

1976 Fiat X1/9 (1300 cc)

The last production models were named the Gran Finale and sold over the 1989/1990 period. They were a dealer modification of the special edition (commonly abbreviated to SE) of 1988/1989, with the addition of a rear spoiler and "gran finale" badges.

The X1/9 in the United States

The X1/9 underwent three generations in the U.S.: 1974 cars, 1975-1978 cars, and 1979-1987 cars.

The 1974 U.S. examples aligned closely with worldwide models, including small (but U.S.-specific) bumpers, 63 hp (47 kW) 1,290cc engines, and four-speed transmissions.

1978 U.S. market Fiat X1/9 with "ladder" bumpers

The 1975-1978 U.S. cars were unique to the U.S. market with "ladder-style" impact absorbing bumpers front and rear. To meet U.S. evaporative and exhaust emission standards, X1/9s were fitted with exhaust gas recirculation valves, air pumps and activated charcoal systems. These cars were rated at 61 hp (45 kW).^[15]

1986 U.S. market Bertone X1/9

In 1979 U.S. cars received increases in displacement to 1,498 cc and five-speed transmissions, with max power up to 67 hp (50 kW).^[15] The 1979 U.S. cars retained the previous emission controls. Model years 1980 and 1981 saw a transition from carburetion to Bosch L-Jetronic fuel injection, with the changeover coming in 1980 for cars sold in California and a gradual changeover for "federal" cars from late 1980 to 1981 model years. The combination of fuel injection (FI), a catalytic converter and unleaded gasoline allowed these cars to meet California's and later federal emission standards. Fuel injected cars were rated at 75 hp (56 kW).^[15]

In 1979 U.S. X1/9s also received both exterior and interior revisions including integrated bumpers front and rear, as well as new front grilles and airdams. The instrument panel and dash redesign moved the heating and ventilation controls from the center console up to the main dash, relocated the radio into the center dash area, moved the fuse panel from the area above the driver's left knee to the area above the passenger's footwell where the glovebox was, and moved the glovebox atop the dash.

During 1982, Fiat ended its presence in the U.S. Fiat turned over marketing and support of the X1/9 to International Automobile Importers, Inc., headed by Malcolm Bricklin, and turned over full production duties to Bertone. In 1983 the orphaned X1/9 was sold as the "Bertone X1/9". IAI and Bertone continued to update the X1/9, providing improved rust protection, revised seating to accommodate taller drivers, and a modernized electrical system for 1984 models.

U.S. sales of the X1/9 fell in the final few years, and 1987 was the last year that IAI imported X1/9s to the U.S.

From mid-1987 to end of the production in 1989, Bertone X1/9s were imported to the U.S. by M.I.K. Automotive, Inc. in North Hollywood, California, owned by Miro Kefurt, who at that time was the number one Bertone dealer in the U.S. and one of the very few that sold exclusively X1/9s. The last four X1/9s were imported to the U.S. in April 1990 (1989 model year produced 12/1989).

U.S. X1/9 model year changes

Model year	Differentiating characteristics
1974	Small wrap-around steel bumpers with large rubber blocks; chrome trim rear fascia; oval holes in rear lower valence; manual choke (operating knob located between the seats); no access panel to distributor from spare tire well.
1975	Ladder-style aluminum bumpers; aluminium grille replaced oval holes in rear valence; automatic choke controlled by coolant temperature.
1977	Production included an unknown number of "special edition" cars with interior colours and trims and exterior striping unique to the edition. Affixed to the right fender, the identifying label had the Italian flag, a four digit serial number, and Nuccio Bertone's signature. First year for distributor access panel in spare wheel compartment.
1978	Late-1978 cars relocated the front trunk release handle from the glovebox to the left side of the driver's footwell.
1979	First major makeover included: square, aluminium bumpers with "elephant ears" side trim; horizontal slat front grille; revised interior included new dash, new seating; drivetrain improvements included 1.5L engine with Bosch electronic ignition, five-speed transaxle, more durable axles and wheel bearings; raised engine cover to accommodate taller engine; addition of a full-width access panel between the engine compartment and rear trunk; modern fuse and relay center; the words "five speed" added to the redesigned "X1/9" model designation badge on the right rear decklid.
1980	Bosch L-Jetronic fuel injection fitted to California cars; additional vent cutout added to sides of engine cover; on fuel injected cars, radio antenna moved from left to right rear fender, sideview mirrors moved from door mounting to through-glass mounting.
1981	Bosch L-Jetronic fuel injection fitted to federal (49-state) cars.
1982	Newly offered two-tone paint scheme with the paint line midway up the wheel arches.
1983	First year that Bertone-logo badges replaced FIAT wreath badges on the front nose and rear decklid.
1984	Electrical system modernized (GBC fuses are replaced by ATC blade style fuses in the fuse and relay centre under the dash just below the glove box). New two-tone paint scheme with the paint line higher on the body, just below the greenhouse. First year for Cromodora CD-179 wheels (nicknamed "Trons"). Optional full-width rear decklid spoiler available.
1985	Bumper finish changed from anodized aluminium to flat black. "X1/9 fuel injection" model badge on right rear decklid discontinued.
1986	Sail panel moulding/trim finish changed from natural aluminium to flat black. Added federally-required center high mounted stop light (CHMSL) for cars manufactured after January 1, 1986; mounted in rear window just below the targa bar.
1987	Minor appearance makeover includes wide body side mouldings, fully padded three-spoke steering wheel, cosmetic changes to climate controls on AC-equipped cars. First year for Speedline "phone dial" wheels. Full "blackout" treatment to windshield mouldings, door frame surround mouldings, and sail panel trim and moulding pieces.
1988	No changes
1989	Last year for model and no changes

Fiat X1/9 Superlight

The first was an all-aluminum body shell, developed in concert with ALCAN. Five all-aluminum cars, dubbed "Superlight" (not Superleggera), were built to the same strength and stiffness of the normal steel cars, and tested for vibration, noise, high load input, and corrosion. Weight savings were 1/3 of the normal steel body.^[16]

Fiat X1/9 "Passo Lungo"

The second design study was a 2+1 completed in 1981, dubbed "Passo Lungo." Two inches of width was added to the entire car, and more than seven inches of length was added behind the door and ahead of the rear wheels. The spare tire was relocated to the new space behind the driver's seat, and a third seat was added to the space behind the passenger seat originally used for the spare tire. "Opera" windows were added to the sail panels. The stock 1.5L engine was replaced by the 2.0L DOHC FIAT engine to add more power to compensate for the added weight.

The X1/9 "Passo Lungo" was based on a European specification 1500 Fiat X/19 with a stretched wheelbase (2.450 metres). Only one example is known to exist which is currently on display with the Bertone collection in Volandia.

The car is interesting in that whilst the body was stretched to accommodate a back seat (only usable by small children) no thought was put into the fact that the targa roof was now so long that it could no longer be stowed in the front boot of the car (as it had been designed for in the normal X1/9).

Fiat X1/9 Spider

The third study was a full-convertible top (Spider) version of the X1/9. The fixed rear window and sail panels were deleted, and a more conventional roll bar/hoop was added for rollover protection. A fascia was fabricated to mate with the engine compartment lid to cover the body shoulders where the sails panels used to be. The convertible top is not a structure that emerges from behind the passenger compartment area; rather it is a flexible cover that mounts using the original targa top clips along the windshield in front, stretches over and is supported by the new roll bar, and is secured into place in the rear with twist-clips.

Examples of all three design studies are now on display in the Volandia Museum adjacent to the Malpensa/Milan airport, which is the new home of the majority of the Bertone collection that was sold after the company went thru final bankruptcy proceedings.

Filipinetti

The Filipinetti X1/9 of Scuderia Filipinetti was presented first at the Geneva Motor Show on 15/3/1973- 25/3/1973 as the first Fiat X1/9 race car. It was built in coorporation with Fiat by the technician and racer Mike Parkes who later developed and built the Lancia Stratos. The Filipinetti had a 1290 cc engine with Lucas mechanical fuel injection. The power was about 160 hp (119 kW) at 8600 rpm with a top speed of 210 km/h (130 mph).^[17]

Abarth

The Fiat subsidiary Abarth, in 1973, developed the Abarth X1/9 Prototipo to replace the 124 Spider Abarth as Fiat's main rally car.^[18] Ultimately, the parallel 131 Abarth project was chosen over the X1/9 as the main rally competition platform.

The X1/9 Prototipo used an 1840 cc engine (a bored out 1600 cc 124-derived unit) with a custom 16-valve cylinder head fed by twin 44 mm Weber IDF carburettors. Externally the cars sported flared wheel-arches, a small "duck tail" spoiler and an F1 style air intake designed to feed the carburettors cool air from above the cars roof. All the X1/9 Prototipos were raced in the traditional Abarth lime-green/yellow and orange/pink colour scheme.

The prototype nature of the X1/9 Prototipo project means that the exact number of cars produced is impossible to define. Components and entire body-shells were routinely swapped and replaced as part of the development process, but it is believed that 5 genuine cars were produced.

Dallara Icsunonove

A Dallara Icsunonove

In 1975 the X1/9 was chosen by Dallara to enter the World Championship for Makes in the Group 5 Special Production class.^[19] The Dallara Icsunonove (the Italian pronunciation of "X1/9") featured a modified X1/9 engine with a custom 16-valve cylinder-head and fundamental suspension and body/monocoque alterations, the most obvious of which are the massively flared wheel-arches and the oversized rear wing.^[20]

Faran

The Faran Car Co. Ltd. was a U.K based company that offered both D-I-Y kit and in-house assembled options for their Eliminator kit. The design featured replacement fibreglass mouldings for the front and rear wings, together with front and rear integrated bumper sections. The external modifications were completed by side sill skirts and a rear boot spoiler which was not dissimilar in style to that found on a De Tomaso Pantera. Faran also offered conversions using Lancia or Fiat Twin Cam engine units, although some owners opted to keep the original SOHC setup. Production of the Faran kits ended following an unfortunate factory fire.

Eurosport

1988 - X1/9 1500 cc

Eurosport (UK) Ltd. is an X1/9 parts specialist that produced two kit variants commonly referred to as the full and bolt-on kits. The full kit was a contender to the Faran version and utilises wide replacement fibreglass moldings for the front and rear wings, together with front and rear integrated bumper sections. Side skirts completed the styling which featured Ferrari Testarossa style side air intake mouldings ahead of the rear wheels. The bolt-on kit in contrast featured replacement front and rear integrated bumper sections that were moulded to blend with the standard wings. This allowed the 1500 alloy bumpers to be substituted with ease and offer a more modern appearance. Side sill skirts were also included in the bolt-on kit. Both kits are still available today.^[21]

Schult

The Schult X1/9 kit was produced in Germany and could again be likened to have taken some inspiration from the Testarossa style, but with more angular lines. Current availability for the Schult conversion is unknown.

Paint codes

X1/9 Interior, roof off

Paint codes for mica red (408) and mica blue (407) (1988 to 1989) are not listed in Fiat paint catalogues (they are Bertone colours) but are listed in Volvo paint catalogues. The colours used on the contemporary Volvo 780 are identical to those used on the X1/9 (even using the same 408/407 codes) as the two cars were produced, and painted, by Bertone in the same factory at the same time.