ifconfig

ifconfig is a system administration utility in Unix-like operating systems for network interface configuration.

The utility is a command line interface tool and is also used in the system startup scripts of many operating systems. It has features for configuring, controlling, and querying TCP/IP network interface parameters. Ifconfig originally appeared in 4.2BSD as part of the BSD TCP/IP suite.

Usage

Common uses for ifconfig include setting the IP address and netmask of a network interface and disabling or enabling an interface.[1] At boot time, many UNIX-like operating systems initialize their network interfaces with shell-scripts that call ifconfig. As an interactive tool, system administrators routinely use the utility to display and analyze network interface parameters. The following two examples show the output of the tool when querying the state of a single active interface each on a Linux-based host (interface eth0) and the ural0 interface on an OpenBSD installation.

 eth0      Link encap:Ethernet  HWaddr 00:0F:20:CF:8B:42
           inet addr:192.168.1.128  Bcast:  Mask:255.255.255.192
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:2472694671 errors:1 dropped:0 overruns:0 frame:0
           TX packets:44641779 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1761467179 (1679.7 Mb)  TX bytes:2870928587 (2737.9 Mb)
           Interrupt:28
 ural0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
         lladdr 00:0d:0b:ed:84:fb
         media: IEEE802.11 DS2 mode 11b hostap (autoselect mode 11b hostap)
         status: active
         ieee80211: nwid ARK chan 11 bssid 00:0d:0b:ed:84:fb  100dBm
         inet 172.30.50.1 netmask 0xffffff00 broadcast 172.30.50.255
         inet6 fe80::20d:bff:feed:84fb%ural0 prefixlen 64 scopeid 0xa

Media access control functions

ifconfig is also commonly used to change the media access control (MAC) address of an interface. In this process, the network interface is first disabled (set down) with the ifconfig command, followed by a MAC change command:

ifconfig wlan0 down
ifconfig wlan0 hw ether 13:11:20:33:49:66
ifconfig wlan0 up

Release status

The free Berkeley Software Distribution UNIX operating systems (e.g., NetBSD, OpenBSD, and FreeBSD) continue active development of ifconfig and extension of its functionality to cover the configuration of wireless networking interfaces, VLAN trunking, controlling hardware features such as TSO or hardware checksumming or setting up bridge and tunnel interfaces. Solaris has historically used ifconfig for all network interface configuration, but as of Solaris 10 introduced dladm to perform data-link (OSI model layer 2) configuration, reducing ifconfig's purview to IP configuration.

In older Linux distributions, ifconfig, in conjunction with the route command, was used to connect a computer to a network, and to define routes between networks. ifconfig for Linux is part of the net-tools package, released as the latest version 1.60 on April 15, 2001.[2]

Some Linux distributions have deprecated the use of ifconfig and route in favor of the software suite iproute2,[3] which has been available since 1999 for Linux 2.2.[4] iproute2 includes support for all common functions of ifconfig(8), route(8), arp(8) and netstat(1). It also includes multicast configuration support, tunnel and virtual link management, traffic control, and low-level IPsec configuration, among other features.

Another higher-level Linux command line tool is ifup (including ifdown and ifquery). In addition to controlling the interfaces, it also provides control of other aspects of the network such as specifying the DNS servers to use. The command is configured using the file /etc/network/interfaces, which contains "stanzas" for each interface.

Network Manager is a Linux daemon that automatically reconfigures the network in dynamic environments, such as moving between WiFi hotspots. It is usually used in conjunction with a graphical front-end such as GNOME Shell.

Versions of Microsoft Windows from Windows 95 to Windows Me used winipcfg to give a graphical display of current IP information. ipconfig, a command similar to ifconfig, comes with Microsoft operating-systems based on the Windows NT kernel. ipconfig also controls the Windows DHCP client.

In macOS, the ifconfig command functions as a wrapper to the IPConfiguration agent, and can control the BootP and DHCP clients from the command-line. Use of ifconfig to modify network settings in Mac OS X is discouraged, because ifconfig operates below the level of the system frameworks which help manage network configuration. To change network settings in Mac OS X from the command line, use /usr/sbin/ipconfig or /usr/sbin/networksetup.

iwconfig, a component of Wireless tools for Linux, which took its name from ifconfig, manages wireless network interfaces outside the original scope of Linux's ifconfig. iwconfig sets such specialized settings as a wireless network's SSID and WEP keys, and functions in tandem with iwlist. Linux also features iwspy, to read the signal, noise and quality of a wireless connection.

Other related tools for configuring Ethernet adapters are: ethtool, mii-tool, and mii-diag for Linux and show-link for Solaris.

See also

References

  1. Linux Network Administrators Guide Section 5.7. Interface Configuration for IP
  2. Upstream URL http://net-tools.sourceforge.net/
  3. Gundersen, Tom. "News: Deprecation of net-tools". Retrieved 4 August 2011.
  4. ip(8) man page

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.