Pro Electron

Pro Electron or EECA is the European type designation and registration system for active components (such as semiconductors, liquid crystal displays, sensor devices, electronic tubes and cathode ray tubes).

Pro Electron was set up in 1966 in Brussels, Belgium. In 1983 it was merged with the European Electronic Component Manufacturers Association (EECA) and since then operates as an agency of the EECA.

The goal of Pro Electron is to allow unambiguous identification of electronic parts, even when made by several different manufacturers. To this end, manufacturers register new devices with the agency and receive new type designators for them.

Designation system

Examples of Pro Electron type designators are:

• AD162 – Germanium power transistor for audio frequency use
• BY133 – Silicon rectifier
• BZY88C5V1 – Silicon 5.1 volt Zener diode
• CQY97 – light emitting diode
• ECC83 – 6.3 volt heater noval dual triode
• A63EAA00XX01 – Color TV picture tube
• SAA1300 – Digital integrated circuit

Pro Electron took the popular European coding system in use from around 1934 for valves (tubes), i.e. the Mullard–Philips tube designation, and essentially re-allocated several of the rarely used heater designations (first letter of the part number) for semiconductors. The second letter was used in a similar way to the valves naming convention: "A" for signal diode, "C" for low-power bipolar transistor or triode, "D" for high-power transistor (or triode), and "Y" for rectifier, but other letter designations did not follow the vacuum tube mode so closely.

The three digits (or letter followed by two digits) after the first two letters were essentially a sequence number, with (at first) a vestige of the valve-era convention that the first one or two digits would indicate the base (package) type in examples such as in this family of general-purpose transistors:

... where x may be:

• 7 for high voltage
• 8 for general purpose
• 9 for low noise/high gain

Pro Electron naming for transistors and Zener diodes has been widely taken up by semiconductor manufactures around the world. Pro Electron naming of integrated circuits, other than some special (e.g. television signal-processing) chips, did not greatly take hold (even in Europe). Other popular designation systems were used for many integrated circuits.

Electron tubes

• See Mullard–Philips tube designation for details. A brief summary of just the more common letters is:

    ECC81
   /  \ \\__ last digit(s) give serial number
  /    \ \__ first digit(s) indicate base (3=octal, 8 or 18 or 80=Noval (B9A), 9=Miniature 7-pin (B7G).
 /      \___ one letter per valve unit in the tube:
D=1.4v or less      A=single-diode (low power)
E=6.3v*             B=double-diode (usually shared cathode, but not always)
P=300mA             C=triode
U=100mA             F=pentode (low power)
                    L=pentode (high power)
                    Y=Single-phase rectifier
                    Z=Full-wave rectifier
* Note: some 6.3 volt heater types have a split heater allowing series (12.6 volt; the
  default for Noval pins 4 to 5) or parallel (6.3 volt) operation.

Semiconductor diodes and transistors

As listed above, the first letter gives the semiconductor type; the second letter denotes the intended use:

A 3-digit sequence number (or one letter then 2 digits, for industrial types) follows.^[1] Examples are:

With early devices, the number indicated the case type. Suffixes may be used, such as a letter (e.g. "C" often means high h_FE, such as in: BC549C^[2]). Other codes may follow to show gain (e.g. BC327-25) or voltage rating (e.g. BUK854-800A^[3]). A BC546 might only be marked "C546", thus possibly creating confusion with JIS abbreviated markings, because a transistor marked "C546" might also be a 2SC546.

• Short summary of semiconductor diode and transistor designations

    BC549C
   /  \ \ \___ variant (A,B,C for transistors implies low, medium or high gain)
  /    \ \____ serial number (3 digits or letter and 2 digits)
 /      \_____ device type:
A=Germanium     A=Signal diode
B=Silicon       C=LF low-power transistor
C=GaAs          D=Power transistor
                F=RF transistor (or FET) 
                P=Photosensitive transistor
                T=Triac or thyristor
                Y=Rectifier diode
                Z=Zener diode

Integrated circuits

• Linear ICs begin with the letter "T", e.g. TAA570 limiter–amplifier and FM detector.
• Logic ICs begin with the letter "F".
  • The FJ family is TTL (e.g. the FJH231 is a quadruple 2-input Open-collector NAND gate equivalent to the SN7401)
  • The FC family is DTL
  • The FD family is MOS.
• Mixed analog/digital ICs begin with the letter "U", e.g. UAA180 LED bargraph A/D and driver.

   FCH171
  //  \ \__ serial number, gives the count and type of gates for example
 //    \___ H=gate ("Combinatorial circuit") J=flip-flop K=monostable Q=RAM R=ROM etc.
FC=DTL
FD=MOS
FJ=TTL

Unfortunately the serial number does not specify the same type of gate in each family, e.g. while an FJH131 is a quadruple 2-input NAND gate (like the 7400), an FCH131 is a dual 4-input NAND gate.^[1]

See also

• JEDEC
• JIS semiconductor designation
• Mullard–Philips tube designation
• RMA tube designation
• RETMA tube designation
• Russian tube designations
• Soviet integrated circuit designation
• East German integrated circuit designation

References

External links

• Pro Electron
• European Type Designation Code System for Electronic Components (15 ed), Pro-Electron, Brussels, Belgium, 6/2008; with tube designation systems