Aeronca Aircraft

Origins

The Aeronca Aircraft Corporation was founded November 11, 1928, in Cincinnati, Ohio. Backed by the financial and political support of the prominent Taft family and future Ohio senator Robert A. Taft who was one of the firm's directors, Aeronca became the first company to build a commercially successful general aviation aircraft.^[3] When production ended in 1951, Aeronca had sold 17,408 aircraft in 55 models.

Aeronca C-2 registered CF-AOR in the Canada Aviation Museum, Rockcliffe (Ottawa) Ontario, 2006

Production began with the Jean A. Roche-designed Aeronca C-2 monoplane, often called the "Flying Bathtub", in 1929. The next major model was the Scout of 1937, a two-seater, which was developed into the Chief and Super Chief the next year.

In 1937 there was a major flood at the Lunken Airport, resulting in the entire airport area being washed away. Aeronca's factory was destroyed, along with the tooling and almost all of the very early blueprints and drawings. At this time a decision was made to move the operation to a more stable area. Middletown, Ohio, was chosen, and the company has remained there ever since.^[1][2] All of the airplanes produced from the start of production in 1929 to 1937 are known as the "Lunken" Aeroncas. The first Aeronca built in Middletown was produced on June 5, 1940, and after this time all Aeroncas were built here.

World War II

The Defender, a tandem trainer version of the Chief with a higher rear seat, was used in training many of the pilots who flew in World War II. ^{[1] [2]}

Several observation and liaison aircraft designs were also produced during and after the war, seeing extensive front line use, including the L-3, L-16 and O-58. ^{[1] [2]}

A glider-trainer version of the Defender, the Aeronca TG-5, replaced the engine with a third seat, facilitating the training of combat glider pilots destined to fly larger craft, such as the Waco CG-4A. ^{[1] [2]}

Aeronca's World War II designs—the Defender, TG-5 and L-3 variants—differed significantly from nearly all previous and subsequent Aeroncas by replacing Aeronca's traditional three-longeron, triangular-cross-section fuselage with a four-longeron, rectangular-cross-section fuselage for additional strength. ^{[1] [2]}

Postwar

1946 7AC Champion

In 1945, following the end of World War II, Aeronca returned to civilian production with two new models, the 7AC Champion and the 11AC Chief. While the Champ shared its tandem seating arrangement with the prewar tandem trainer—and the Chief shared its name and seating arrangement with the prewar Chief designs—both were new designs, and very similar to each other. ^{[1] [2] [4] [5] [6]}

1940 Aeronca 11AC Chief

A benefit of the concurrent development was that the new designs had about 80% of their parts in common. Nevertheless, the tandem-seat Champ—resembling the extremely popular Piper J-3 Cub—was favored by the market, evidenced by its outselling its sibling, the Chief, at a rate of 4 to 1. Between 1945 and 1951, nearly 8,000 Champions were manufactured (becoming one of the most popular light planes of all time); while over the same period, approximately 2,000 Chiefs were produced. ^{[1] [2] [4] [5] [6]}

New ownership

Aeronca ceased light aircraft production in 1951, and in 1954 sold the Champion design to the new Champion Aircraft Corporation of Osceola, Wisconsin, which continued building variants of the Champion as well as the derivative design, the Citabria. The venerable aircraft design was acquired again by the Bellanca Aircraft Company in 1970 and again to American Champion in 1988, where it remains in production.^[1][2]

In the early 1970s, Aeronca was contracted by Bede Aircraft to assemble its first Bede BD-5J Microjet—the world's smallest jet airplane—but, after its experiences with the prototype, Aeronca declined to be further involved with the program.^[1][2]

In 1978 Aeronca planned to start aircraft production again with production of a prototype very light business jet, the Foxjet ST600. The project was eventually cancelled due to lack of WR-44 engine availability.^[7]

Aeronca now builds components for aerospace companies including Boeing, Northrop Grumman, Lockheed and Airbus. In its 23-year history as a general aviation and military aviation manufacturer, Aeronca produced 17,408 aircraft spanning 55 different models.