Microscanner

Common chip dimensions are 4 mm × 5 mm for mirror diameters between 1 and 3 mm.[1] However larger mirror apertures with side measurements of up to approx. 10 mm × 3 mm can also be produced.[2] The scan frequencies depend upon the design and mirror size and range between 0.1 and 50 kHz. The deflection movement is either resonant or quasi-static.[3] With microscanners that are capable of tilting movement, light can be directed over a projection plane.

Many applications requires that a surface is addressed instead of only a single line. For double resonant operation, which results in sinusoidal scan motion, a Lissajous pattern is written. Mechanical deflection angles of such micro scanning devices reach up to ±30°.[4] With translational (piston type) microscanners a mechanical stroke of up to approx. ±500 µm can be attained.[5] This configuration is energy efficient, but requires complicated control electronics. For high end display applications the common choice is raster scanning, where a resonant scanner (for the longer display dimension) is paired with quasi-static scanner (for the shorter dimension).[3]

The required drive forces for the mirror movement can be provided by various physical principles. In practice, the relevant principles for driving such a mirror are the electromagnetic, electrostatic, thermo-electric and piezo-electric effects.[3] Because the physical principles differ in their advantages and disadvantages, a suitable driving principle should be chosen according to the application. Specifically, the mechanical solutions required for resonant and quasi-static scanning, respectively, are very different from each other. Thermo-electric actuators are not applicable for high frequency resonant scanners, but the other three principles can be applied to the full spectrum of applications.

For resonant scanners one often employed configuration is the indirect drive. In an indirect drive a small motion in a larger mass is coupled to a large motion in a smaller mass (the mirror) through mechanical amplification at a favorable mode shape. This is in contrast to the more common direct drive, where the actuator mechanism moves the mirror directly. Indirect drives have been implemented for electromagnetic,[6] electrostatic,[7] as well as piezo-electric actuators.[8] [9] There is no general answer to the question if the direct or indirect drive is more efficient, but judging by the performance of existing scanners the indirect drive appears to have the largest impact for piezoelectric scanners.[3]

Electrostatic actuators offer high power similar to electromagnetic drives. In contrast to an electromagnetic drive, the resulting drive force between the drive structures cannot be reversed in polarity. For the realization of quasi-static components with positive and negative effective direction, two drives with positive and negative polarity are required.[10] As a rule of thumb, vertical comb drives are utilized here. Nevertheless, the highly non-linear drive characteristics in some parts of the deflection area can be hindering for controlling the mirror properly. For that reason many highly developed microscanners today utilize a resonant mode of operation, where an Eigenmode is activated. Resonant operation is most energy efficient. For beam positioning and applications which are to be static-actuated or linearized-scanned, quasi-static drives are required and therefore of great interest.

Magnetic actuators offer very good linearity of the tilt angle versus the applied signal amplitude, both in static and dynamic operation. The working principle is that a metallic coil is placed on the moving MEMS mirror itself and as the mirror is placed in a magnetic field, the alternative current flowing in the coil generate Lorentz force that tilts the mirror. Magnetic actuation can either be used for actuating 1D or 2D MEMS mirrors. Another characteristics of the magnetically actuated MEMS mirror is the fact the low voltage is required (below 5V) making this actuation compatible with standard CMOS voltage. An advantage of such actuation type is that MEMS behavior does not present hysteresis, as opposed to electrostatic actuated MEMS mirrors, that make it very simple to control. Power consumption of magnetically actuated MEMS mirror can be as low as 0.04 mW.[11]

Thermoelectric drives produce high driving forces, but they present a few technical drawbacks inherent to their fundamental principle. The actuator has to be thermally well insulated from the environment, as well as being pre-heated in order to prevent thermal drift due to environmental influences. That is why the necessary heat output and power consumption for a thermal bimorph actuator is relatively high. One further disadvantage is the comparably low displacement which needs to be leveraged to reach usable mechanical deflections. Also thermal actuators are not suitable for high frequency operation due to significant low pass behaviour.

Piezo-electrical drives produce high force, but as with electro-thermal actuators the stroke length is short. Piezo-electrical drives are, however, less susceptible to thermal environmental influences and can also transmit high-frequency drive signals well. To achieve the desired angle some mechanism utilizing mechanical amplification will be required for most applications. This has proven to be difficult for quasi-static scanners, although there are promising approaches in the literature using long meandering flexures for deflection amplification.[12][13] For resonant rotational scanners, on the other hand, scanners using piezo-electric actuation combined with an indirect drive are the highest performer in terms of scan angle and working frequency.[8][9][14] However, the technology is newer than electro-static and electro-magnetic drives and remains to be implemented in commercial products.[3]

LDC module with 1D microscanner and integrated optical position sensor on the back side

An electrostatic 2D microscanner in a DIL20 casing

MEMS scanner module for 3D distance measurement (LIDAR) with a single sending mirror (mirror dimensions approx. (9.5 × 2.5 mm)) and a synchronized microscanner array (2 × 7) as receiver unit.

Applications for tilting microscanners are numerous and include:

• Projection displays[3][6][15]
• Image recording, e.g. for technical and medical endoscopes[4]
• Bar code scanning[16]
• Spectroscopy
• Laser marking and material processing
• Object measurement / triangulation[2]
• 3D cameras
• Object recognition
• 1D and 2D light grid
• Confocal microscopy / OCT
• Fluorescence microscopy
• Laser wavelength modulation

Some of the applications for piston type microscanners are:

• Fourier transform infrared spectrometer
• Confocal microscopy
• Focus variation

Wafer with resonant microscanners, ready-processed with the Fraunhofer AME75 process (based on blank BSOI wafers), before dicing the devices.

Detail of a wafer with VarioS® microscanners, developed and produced based on a modular fabrication system at Fraunhofer IPMS.

Microscanners are usually manufactured with surface or bulk micromechanic processes. As a rule, silicon or BSOI (bonded silicon on insulator) are used.

The advantages of microscanners compared to macroscopic light modulators such as galvanometer scanners are based upon their small size, low weight and minimum power consumption. Further advantages arise along with the integration possibilities of position sensor technology[17] and electronics in the component. Microscanners are also extremely resistant to environmental influences. For example, the microscanners developed at one of the globally renowned manufacturing organizations have a shock resistance of at least 2500 g. Under the condition that they are sealed free from dust and humidity, they are by and large, maintenance-free and usually operate at temperatures between -20 °C and +80 °C.

Some of the disadvantages due to the manufacturing process are high costs for single devices and long delivery times. In order to address these problems, various scientists at the named manufacturing organization have attempted to provide a platform technology, which is an advanced MEMS modular system. The system deals with the reduction of this problem, allowing the problem to act with minimal influence; thus raising the admirability of the system technology.

Wikimedia Commons has media related to Microscanner.

• Scanning Micromirrors. Mirrorcle Technologies Gimbal-less, Two-axis scanning micromirrors
• MEMS Scanners. Fraunhofer Institute for Photonic Microsystems
• ARI MEMS Micromirror Demonstration Devices. Adriatic Research Institute
• Getting Started with Analog Mirrors. Texas Instruments (Product Page)
• Magnetic MEMS micromirrors. Lemoptix (Technology description Page)
• MEMS Laser Scanning Mirrors. Maradin Ltd