Crab claw sail

Micronesian proa with crab claw sail
Sandeq boats in Majene, West Sulawesi, Indonesia
The crabclaw sail of the historic tepukei Maunga Nefe.

The crab claw sail or, as it is sometimes known, Oceanic lateen or Oceanic sprit, is a triangular sail with spars along upper and lower edges. The crab claw sail is used in many traditional Pacific Ocean cultures, as can be seen by the traditional proa and tepukei.

Construction

The crab claw sail consists of a sail, approximately an isosceles triangle in shape. The equal length sides are usually longer than the third side, with spars along the long sides.

The crab claw may also traditionally be constructed with curved spars, giving the edges of the sail along the spars a convex shape, while the leech of the sail is often quite concave to keep it stiff on the trailing edge. These features give it its distinct, claw-like shape. Modern crab claws generally have straighter spars and a less convex leech, which gives more sail area for a given length of spar. Spars may taper towards the leech. The structure helps the sail to spill gusts.

The crab claw characteristically widens upwards, putting more sail area higher above the ocean, where the wind is stronger and steadier. This increases the heeling moment: the sails tend to blow the watercraft over. For this reason, crabclaws are typically used on multihulls, which resist heeling more strongly.

Proa

In a proa, the forward intersection of the spars is placed towards the bow. The sail is supported by a short mast attached near the middle of the upper spar, and the forward corner is attached to the hull. The lower spar, or boom, is attached at the forward intersection, but is not attached to the mast. The proa has a permanent windward and leeward side, and exchanges one end for the other when coming about.

To tack, or switch directions across the wind, the forward corner of the sail is loosened and then transferred to the opposite end of the boat, a process called shunting.[1] To shunt, the proa's sheet is let out. The joined corner of the spars is then transferred to the opposite end of the boat. While remaining attached to the top of the mast, the upper spar tilts to vertical and beyond as the forward corner moves past the mast and onward to the other end of the boat. Meanwhile, the mainsheet is detached and used to rotate the rearward end of the boom through a horizontal half circle. The spar join is then re-attached at the new "forward" end of the boat and the mainsheet is re-tightened at the new "rearward" end.[2]

Tepukei

The Maunga Nefe, a te puke or folafolau was built on Taumako and sailed out of Nifiloli; it was used for travel and trading within the Santa Cruz archipelago.

A shunting rig with the sail propped vertically at the bow, very similar to the proa rig described above.

Non-shunting crab claw

The term "crabclaw sail" is also used for non-shunting sails that widen upwards.[4] The 'ōpe'a, the upper spar, is braced up so high that it is nearly parallel to the mast (as in a gunter rig). The paepae, the lower spar/boom, points well above the horizontal, unlike the boom of most gunter rigs and gaff rigs. The two spars can be brought together or pulled apart with control lines (rigging diagram). The mast is fixed and stayed.[3]

Performance

Crab claw sail being constructed for Hot Buoys trimaran. Notice pocket in right hand edge of sail to hold spar. Second spar in this particular configuration is not required since a bolt-rope holds the sail's upper edge and the mast is located in the back of the sailboat. Note lack of shaping.

The crab-claw sail is something of an enigma. It has been demonstrated to produce very large amounts of lift when reaching, and overall seems superior to any other simple sail plan (this discounts the use of specialised sails such as spinnakers). C. A. Marchaj, a researcher who has experimented extensively with both modern rigs for racing sailboats and traditional sailing rigs from around the world, has done wind tunnel testing of scale models of crab-claw rigs. One popular but disputed theory is that the crab-claw wing works like a delta wing, generating vortex lift. Since the crab claw does not lie symmetric to the airflow, like an aircraft delta wing, but rather lies with the lower spar nearly parallel to the water, the airflow is not symmetric. However, the presence of the water, close to the lower spar and parallel to it, makes the airflow behave roughly like the airflow over half of a delta wing, as though a "reflection" in the water provided the other half (apart from a narrow gap near the water, which causes a small difference there).

This can clearly be seen in Marchaj's wind tunnel photos published in Sail Performance: Techniques to Maximise Sail Power. The vortex on the top spar of the sail is much larger, covering most of the sail area, while the lower vortex is very small and stays close to the spar. Marchaj attributes the large lifting power of the sail to lift generated by the vortices, while others attribute the power to a favourable mix of aspect ratio, camber and (lack of) twist at this point of sail.[5][6]

See also

References

  1. ↑ Gross, Jeffrey L. (2016). Waipio Valley: A Polynesian Journey from Eden to Eden. Xlibris Corporation. p. 626. ISBN 9781479798469.
  2. ↑ Editor (July 23, 2014). "Proa Rig Options: Crab Claw". proafile.com. Proa File. Retrieved 2017-04-21.
  3. 1 2 "Parts of the Hawaiian Canoe". archive.hokulea.com. Retrieved 17 April 2018.
  4. ↑ Star-Bulletin, Honolulu. "starbulletin.com - News - /2007/03/06/". archives.starbulletin.com. Retrieved 17 April 2018.
  5. ↑ Marchaj, C. A. Sail Performance: Techniques to Maximise Sail Power. ISBN 0-07-141310-3.
  6. ↑ Slotboom, Bernard. "Delta Sail in A "Wind Tunnel" Experiences". Experiences from B.J. Slotboom. Retrieved January 7, 2015.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.