Electronic packaging

Electronic packaging is the protective features and enclosures built into electronic devices. Packaging of an electronic system must consider protection from mechanical damage, cooling, radio frequency noise emission and electrostatic discharge. Prototypes and industrial equipment made in small quantities may use standardized commercially available enclosures such as card cages or prefabricated boxes. Mass-market consumer devices may have highly specialized packaging to increase consumer appeal. Electronic packaging is a major discipline within the field of mechanical engineering.[1]

The same electronic system may be packaged as a portable device or adapted for fixed mounting in an instrument rack or permanent installation. Packaging for aerospace, marine, or military systems imposes different types of design criteria. This discipline requires the use of subjects normally only within the skill set of the mechanical engineer with their formal education in dynamics, stress analysis, heat transfer and fluid mechanics. High-reliability equipment often must survive drop tests, loose cargo vibration, secured cargo vibration, extreme temperatures, humidity, water immersion or spray, rain, sunlight (UV, IR and visible light), salt spray, explosive shock, and many more. These subjects typically are not the concern of the product's electrical design engineer since they have enough to do already to make sure the product functions as intended. Also, mechanical engineers have knowledge of the mechanical behaviors of materials and are better qualified to specify, source and test candidate materials and finishes for parts used to protect the core electronics which often consist of circuit card assemblies (CCAs), connectors, cables and "buy-and-bolt" components such as transformers, power supplies, relays, switches, etc. that are not designed to go on a CCA. That's not to say such components cannot be purchased in versions intended for putting on CCAs. Many components come both ways and the choice of which type falls on the mechanical and electrical engineers together who work closely as part of a multi-functional product development team. Lastly, many electrical products require the manufacturing of high-volume, low-cost parts (i.e. enclosures, covers,...) which involve injection molding, die casting, investment casting, and so on. The design of these products depend heavily on the production method and require careful consideration of dimensions and tolerances and tooling design, another specialty in the realm of mechanical engineers. Even complex low-volume parts often require knowledge of specialized manufacturing processes e.g. plaster- and sand-casting of metal enclosures. Lastly, the mechanical engineer is normally more versed in the creation and control of engineering drawings which are ideally drawn in the USA under the auspices of the ASME Y14 family of drawing standards.

In the design of electronic products, electromechanical (E/M) or electronic packaging (mechanical) engineers sometimes perform manual, spreadsheet, computational fluid dynamic (CFD) and/or finite element method (FEM) analyses using handbooks formulas and commercial CFD and FEM programs to estimate such things as maximum CCA component junction temperatures (CFD and FEM), structural resonant frequencies (FEM) and dynamic stresses and deflections (FEM) under worst-case environments. Such knowledge is important to prevent immediate or premature electronic product failures.

So "electronic packaging" is a broad term that usually means a mechanical engineer doing all design work the electrical engineer is not able to do. Of course, a mechanical engineer, with enough education and training, can do the electrical engineer's job. Conversely, the electrical engineer, with enough education and training, can do the mechanical engineer's job. To confuse things, there are "electronic packaging" electrical engineers who design high performance CCA components e.g. systems on chips (SOCs), central processing units (CPUs) etc. for use in electrical circuits most often soldered or wire-bonded to CCAs.

Packaging materials

Sheet metal

Punched and formed sheet metal is one of the oldest types of electronic packaging. It can be mechanically strong, provides electromagnetic shielding when the product requires that feature, and is easily made for prototypes and small production runs with little custom tooling expense.

Cast metal

Gasketed metal castings are sometimes used to package electronic equipment for exceptionally severe environments, such as in heavy industry, aboard ship, or deep under water. Aluminum die castings are more common than iron or steel sand castings.

Machined metal

Electronic packages are sometimes made by machining solid blocks of metal, usually aluminum, into complex shapes. They are fairly common in microwave assemblies for aerospace use, where precision transmission lines require complex metal shapes, in combination with hermetically sealed housings. Quantities tend to be small; sometimes only one unit of a custom design is required. Piece part costs are high, but there is little or no cost for custom tooling, and first-piece deliveries can take as little as half a day. The tool of choice is a numerically controlled vertical milling machine, with automatic translation of computer-aided design (CAD) files to toolpath command files.

Molded plastic

Molded plastic cases and structural parts can be made by a variety of methods, offering tradeoffs in piece part cost, tooling cost, mechanical and electrical properties, and ease of assembly. Examples are injection molding, transfer molding, vacuum forming, and die cutting. Pl can be post-processed to provide conductive surfaces.

Potting

Formally called "encapsulation", potting consists of immersing the part or assembly in a liquid resin, then curing it. Potting can be done in a pre-molded potting shell, or directly in a mold. Today it is most widely used to protect semiconductor components from moisture and mechanical damage, and to serve as a mechanical structure holding the lead frame and the chip together. In earlier times it was often used to discourage reverse engineering of proprietary products built as printed circuit modules. It is also commonly used in high voltage products to allow live parts to be placed closer together, so that the product can be smaller. This also excludes dirt and conductive contaminants (such as impure water) from sensitive areas. Another use is to protect deep-submergence items such as sonar transducers from collapsing under extreme pressure, by filling all voids. Potting can be rigid or soft. When void-free potting is required, it is common practice to place the product in a vacuum chamber while the resin is still liquid, hold a vacuum for several minutes to draw the air out of internal cavities and the resin itself, then release the vacuum. Atmospheric pressure collapses the voids and forces the liquid resin into all internal spaces. Vacuum potting works best with resins that cure by polymerization, rather than solvent evaporation.

Porosity sealing or impregnation

Porosity Sealing or Resin Impregnation is similar to potting, but doesn't use a shell or a mold. Parts are submerged in a polymerizable monomer or solvent-based low viscosity plastic solution. The pressure above the fluid is lowered to a full vacuum. After the vacuum is released, the fluid flows into the part. When the part is withdrawn from the resin bath, it is drained and/or cleaned and then cured. Curing can consist of polymerizing the internal resin or evaporating the solvent, which leaves an insulating dielectric material between different voltage components. Porosity sealing (Resin Impregnation) fills all interior spaces, and may or may not leave a thin coating on the surface, depending on the wash/rinse performance. The main application of vacuum impregnation porosity sealing is in boosting the dielectric strength of transformers, solenoids, lamination stacks or coils, and some high voltage components. It prevents ionization from forming between closely spaced live surfaces and initiating failure.

Liquid filling

Liquid filling is sometimes used as an alternative to potting or impregnation. It's usually a dielectric fluid, chosen for chemical compatibility with the other materials present. This method is used mostly in very large electrical equipment such as utility transformers, to increase breakdown voltage. It can also be used to improve heat transfer, especially if allowed to circulate by natural convection or forced convection through a heat exchanger. Liquid filling can be removed for repair much more easily than potting.

Conformal coating

Conformal coating is a thin insulating coating applied by various methods. It provides mechanical and chemical protection of delicate components. It's widely used on mass-produced items such as axial-lead resistors, and sometimes on printed circuit boards. It can be very economical, but somewhat difficult to achieve consistent process quality. See Conformal coating, Parylene.

Glop-top

A chip-on-board (COB) covered with dark epoxy

Glop-top is a variant of conformal coating used in chip-on-board assembly (COB). It consists of a drop of specially formulated epoxy[2] or resin deposited over a semiconductor chip and its wire bonds, to provide mechanical support and exclude contaminants such as fingerprint residues which could disrupt circuit operation. It is most commonly used in electronic toys and low-end devices.[3]

Surface-mounted LEDs are frequently sold in COB configurations. In these, the individual diodes are mounted in an array that allows the device to produce a greater amount of luminous flux with greater ability to dissipate the resulting heat in an overall smaller package than can be accomplished by mounting LEDs, even surface mount types, individually on a circuit board.[4]

Hermetic metal/glass cases

Hermetic metal packaging began life in the vacuum tube industry, where a totally leak-proof housing was essential to operation. This industry developed the glass-seal electrical feedthrough, using alloys such as Kovar to match the coefficient of expansion of the sealing glass so as to minimize mechanical stress on the critical metal-glass bond as the tube warmed up. Some later tubes used metal cases and feedthroughs, and only the insulation around the individual feedthroughs used glass. Today, glass-seal packages are used mostly in critical components and assemblies for aerospace use, where leakage must be prevented even under extreme changes in temperature, pressure, and humidity.

Hermetic ceramic packages

Packages consisting of a lead frame embedded in a vitreous paste layer between flat ceramic top and bottom covers are more convenient than metal/glass packages for some products, but give equivalent performance. Examples are integrated circuit chips in ceramic Dual In-line Package form, or complex hybrid assemblies of chip components on a ceramic base plate. This type of packaging can also be divided into two main types: multilayer ceramic packages (like LTCC and HTCC) and pressed ceramic packages.

Printed circuit assemblies

Printed circuits are primarily a technology for connecting components together, but they also provide mechanical structure. In some products, such as computer accessory boards, they're all the structure there is. This makes them part of the universe of electronic packaging.

Design considerations

An engineer or designer must balance many objectives and practical considerations when selecting packaging methods.

  • Hazards to be protected against: mechanical damage, exposure to weather and dirt, electromagnetic interference, etc.
  • Heat dissipation requirements
  • Tradeoffs between tooling capital cost and per-unit cost
  • Tradeoffs between time to first delivery and production rate
  • Availability and capability of suppliers
  • User interface design and convenience
  • Ease of access to internal parts when required for maintenance
  • Product safety, and compliance with regulatory standards
  • Aesthetics, and other marketing considerations
  • Service life and reliability

Reliability evaluation

A typical reliability qualification includes the following types of environmental stresses:

See also

References

  1. HB Jackson 34yr exp mechanical engineer in electronic product development in aerospace, defense, rail, SIGINT and CATV/telecom
  2. Venkat Nandivada. "Enhance Electronic Performance with Epoxy Compounds". Design World. 2013.
  3. Joe Kelly. "Improving Chip on Board Assembly". 2004.
  4. Handbook on the Physics and Chemistry of Rare Earths: Including Actinides. Elsevier Science. 1 August 2016. p. 89. ISBN 978-0-444-63705-5.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.