DIN connector

Five-pin male 180° DIN connector from the keyboard of an original IBM PC. Note the unusually thick shielding skirt.

A DIN connector is an electrical connector that was originally standardized in the early 1970s[1] by the Deutsches Institut für Normung (DIN), the German national standards organization. There are DIN standards for a large number of different connectors, therefore the term "DIN connector" alone does not unambiguously identify any particular type of connector unless the document number of the relevant DIN standard is added (e.g., "DIN 45322 connector"). Some DIN connector standards are:

  • DIN 41524, for circular connectors often used for audio signals
  • DIN 41612, rectangular connectors used to connect plug-in cards to a back plane or motherboard
  • DIN 41652 D-subminiature connectors used for computer data and video

In the context of consumer electronics, the term "DIN connector" commonly refers to a member of a family of circular connectors that were initially standardized by DIN for analog audio signals. Some of these connectors have also been used in analog video applications, for power connections and for digital interfaces such as MIDI or the IBM AT computer keyboard (later PS/2 connectors for keyboard and mouse are Mini-DIN connectors). The original DIN standards for these connectors are no longer in print and have been replaced with the equivalent international standard IEC 60130-9.[2]

While DIN connectors appear superficially similar to the professional XLR connectors, they are not compatible.

Circular connectors

All male connectors (plugs) of this family of connectors feature a 13.2 mm diameter metal shield with a notch that limits the orientation in which plug and socket can mate. A range of connectors of the same form that differ only in their pin configuration exist and have been standardized originally in DIN 41524 / IEC/DIN EN 60130-9 (3-pin at 90° and 5-pin at 45°), DIN 45322 (5-pin and 6-pin at 60°), DIN 45323 (6-pin), DIN 45329/IEC 10 (7-pin at 45°), DIN 45326 / IEC/DIN EN 60130-9 (8-pin at 45°), and other standards for a range of different applications, including the following examples:

The plugs consist of a circular shielding metal skirt protecting a number of straight round pins. The pins are 1.45 mm in diameter and equally spaced (at 90°, 72°, 60° or 45° angles) in a 7.0 mm diameter circle. The skirt is keyed to ensure that the plug is inserted with the correct orientation, and to prevent damage to the pins. The basic design also ensures that the shielding is connected between socket and plug prior to any signal path connection being made. However, as the keying is consistent across all connectors, it does not prevent incompatible connectors from mating, which can lead to damage; this is changed in Mini-DIN, which keys different connectors. Additionally, some "domino" 5-pin connectors had a keyway on opposing sides of the plug, allowing it to be reversed. If used as a headphone connector, that allowed the left and right channels to be transposed, and similarly if used as a serial data connection the transmit and receive lines could be crossed (although the standard pinout adopted by Acorn did not allow for this).[3]

There are seven common patterns, with any number of pins from three to eight. Three different five-pin connectors exist, known as 180°, 240°, and domino/360°/270° after the angle of the arc swept between the first and last pin (see figures above). There are also two variations of the six-pin, seven-pin and eight-pin connectors, one where the outer pins form 360° and one where they form 270°.[4] There is some limited compatibility, for example a three-pin connector will fit any 180° five-pin socket, engaging three of the pins and leaving the other two unconnected, a 180° five-pin plug will fit into a seven- or eight-pin socket. 3-pin and 180° 5-pin connectors will also fit the 270° 7-pin and both 8-pin sockets. In addition to these connectors, there are also connectors with 10, 12 and 14 pins. Some high-range equipment used seven-pin connectors where the outer two carried digital system data:[5] if the connected equipment was incompatible, the outer two pins could be unscrewed from plugs so that they fitted into standard five-pin 180° sockets without data connections.

Screw-locking versions of this connector have also been used in instrumentation, process control and professional audio.[6] In North America this variant is often called a "small Tuchel" connector after one of the major manufacturers. Tuchel is now a division of Amphenol. Additional configurations up to 24 pins are also offered in the same shell size. A version with a bayonet locking ring was used on portable tape recorders, dictation machines and lighting dimmers and controls through the from the 1960s to the 1980s, an example of this is the microphone input connector and some others on the "Report" family of UHER (brand) tape recorders. The bayonet locking version is sometimes referred to by the trade name Preh. Belling Lee offered a version with a sprung-loaded collar which latched on insertion but required the collar to be pulled back to release the connector, similar to the LEMO B series connector. This connector was commonly referred to as the "Bleecon",[7] an example of its use is the Strand Tempus range of theatrical lighting dimmers and control desks.[8] A version with a pushbutton latch similar to that on an XLR cable mounted socket was also available. Female connectors with screw-locking, Bleecon or bayonet latching features are compatible with standard DIN plugs.

Some manufacturers offered panel-mounted jacks with potential-free auxiliary contacts that would open if a plug were inserted.

Loudspeaker connector

Speaker DIN line socket (left) and plug (right)

A polarised two-pin unshielded connector, designed for connecting a loudspeaker to a power amplifier (or other device; many of the earlier shoebox style tape recorders used them), is known as the DIN 41529 loudspeaker connector. It exists as a panel-mounting female version, and line-mounted male and female versions. The male version has a central flat pin, and circular pin mounted off-centre. The circular pin is connected to the positive line (red) while the spade is connected to the negative line (black).[9] The panel-mounting female version is available with or without an auxiliary contact that disconnects the internal speaker of the device if an external speaker connector is inserted. Most common is a three-hole female connector with one circular hole on either side of the spade hole, one of them with an aux contact and one without, which provides the option to leave the internal speaker connected by inserting the plug twisted by 180°.

It is now mainly found on older equipment, such as 16 mm movie projectors. The Becker radio found in many Mercedes-Benz automobiles uses this connector. The same connector is used on some LED lamps and halogen lamps to connect the bulb to the power supply. The two-pin DIN plug lacks the outer metal shell, so far less force is required to disconnect the plug accidentally. Worn two-pin speaker plugs often require only the slightest nudge to break contact. There are also three- and four-pin versions of this loudspeaker connector used for example by Bang & Olufsen.

Applications

Analog audio

The 3/180° and 5/180° connectors were originally standardized and widely used in European countries for interconnecting analog audio equipment. For example, a stereo tape recorder could connect to a stereo amplifier using the five pins for the four signal connections plus ground. The connectors on the cord are connected pin for pin, (pin 1 to pin 1, etc.). Pins on male connectors are numbered (from right to left, viewed from outside of the connector, with the 5 pins upwards, and facing them): 1–4–2–5–3. Holes on female connectors are also numbered 1-4-2-5-3, but from left to right (facing the holes). A four-conductor cord wired in this way is sometimes called a DIN cord, a DIN lead or a DIN cable. For mono interconnections, the 3/180° plugs are sufficient. When a mono plug is inserted into a stereo socket, it mates with the left channel. This interface was rare in the U.S. market, and has progressively disappeared on new equipment, both in Germany and worldwide, since the 1980s, in favour of RCA connectors.

Application Connector Pin function
14253
Amplifier Monophonic 5/180° Audio out Screen/return Audio in
Stereophonic Left out Right out Right in Left in
Tape recorder Monophonic Audio in Audio out
Stereophonic Left in Right in Right out Left out

Other uses

The 5/180° connectors are commonly used for:

  • SYNC or MIDIinterface for electronic musical instruments,
  • Peripherals or power connectors for personal computers
  • Audio in the original HME wireless communicators, it is the headset connector for (Tx & Rx) Inbound and Outbound audio for Drive Through Restaurants
  • Controlling tilt of UMTS Antennas (Antenna Interface Standards Group)[10]
  • Connecting two controllers for radio controlled model aircraft together for training purposes.

The DIN connector saw several other uses apart from audio. It was particularly popular as a connector for various home computers and video game consoles.

Analogue theatrical lighting control (pre-dating the more recent digital control protocols such as DMX) commonly used the 8-pin (45°) DIN connector, six of the pins being 0-10V control signals for six separate dimmer circuits, and the other two a 0V reference and a DC source for powering simple circuitry in rudimentary lighting desks. Pinouts vary between manufacturers: Zero 88, Anytronics, Lightprocessor and Strand have the control signals on pins 1-6, 0V on pin 8 and power on pin 7 and Pulsar and Clay Paky have power on pin 1, 0V on pin 2 and channel outputs on pins 3 to 8. The polarity of the power supply and control signals relative to ground also varies, with Strand having negative voltages but most other brands having positive voltages.[11]


In the Soviet Union, 3-pin and 5-pin DIN connectors named ОНЦ-ВГ (Latin: ONC-VG), could be seen on many pieces of equipment, as well as factory-made audio equipment. Radio amateurs and small cooperatives quickly discovered these reliable connectors and began to put them into almost every low frequency signal device, often with non-standard pin usage. Versions other than 3 or 5-pin were very rare in the USSR and very hard to buy. 4-pin DIN connectors, for example, were never seen on any device or in stores.

See also

References

  1. ↑ Deutsches Institut für Normung (March 1974). "DIN 41524:1974-03: Dreipolige und fünfpolige Steckverbinder für Rundfunk- und verwandte Geräte". Beuth Verlag GmbH. Retrieved 2017-04-01.
  2. ↑ IEC 60130-9: "Connectors for frequencies below 3 MHz — Part 9: Circular connectors for radio and associated sound equipment." International Electrotechnical Commission, Geneva, 2011.
  3. ↑ "Why are domino plugs reversible". stardot.org.uk. Retrieved 2017-05-10.
  4. ↑ "Amabilidade 8-pin DIN Connectors". Amabilidade2002.com. Retrieved 2012-07-28.
  5. ↑ "Sounds Heavenly - Help and Advice". Retrieved 2009-03-19.
  6. ↑ IEC 60268-11
  7. ↑ "Bleecon". www.blue-room.org.uk. Retrieved 2017-05-09.
  8. ↑ "Bleecon". www.blue-room.org.uk. Retrieved 2017-05-09.
  9. ↑ Carter, Simon (2010). "DIN Connectors". Electronics 2000. Retrieved 27 March 2010.
  10. ↑ "AISG Website". 5 March 2009. Retrieved 8 May 2009.
    AISG (13 June 2006). "Control interface for antenna line devices" (PDF). Archived from the original (PDF) on 20 July 2011. Retrieved 8 May 2009.
  11. ↑ "0 to 10V Analog Control Protocol". Retrieved 2017-05-10.

  • DIN Connectors
  • IEC 60574-3: Audiovisual, video and television equipment and systems — Part 3: Specification for connectors for the interconnection of equipment in audiovisual systems.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.