Coplanar waveguide

Cross section of a conductor-backed coplanar waveguide transmission line
A 517 µm tall copper coplanar waveguide created using LIGA technique.[1]

Coplanar waveguide is a type of electrical planar transmission line which can be fabricated using printed circuit board technology, and is used to convey microwave-frequency signals. On a smaller scale, coplanar waveguide transmission lines are also built into monolithic microwave integrated circuits. Conventional coplanar waveguide (CPW) consists of a single conducting track printed onto a dielectric substrate, together with a pair of return conductors, one to either side of the track. All three conductors are on the same side of the substrate, and hence are coplanar. The return conductors are separated from the central track by a small gap, which has an unvarying width along the length of the line. Away from the cental conductor, the return conductors usually extend to an indefinite but large distance, so that each is notionally a semi-infinite plane.

Conductor-backed coplanar waveguide (CBCPW) is a common variant which has a ground plane covering the entire back-face of the substrate. The ground-plane serves as a third return conductor.

Coplanar waveguide was invented in 1969 by Cheng P. Wen, primarily as a means by which non-reciprocal components such as gyrators and isolators could be incorporated in planar transmission line circuits.[2]

The electromagnetic wave carried by a coplanar waveguide exists partly in the dielectric substrate, and partly in the air above it. In general, the dielectric constant of the substrate will be different (and greater) than that of the air, so that the wave is travelling in an inhomogeneous medium. In consequence CPW will not support a true TEM wave; at non-zero frequencies, both the E and H fields will have longitudinal components (a hybrid mode).

Nonreciprocal devices

Nonreciprocal gyromagnetic devices depend on the microwave signal presenting a rotating (circularly polarized) magnetic field to a statically magnetized ferrite body. CPW is designed to produce just such a rotating magnetic field in the two slots between the central and side conductors.

The dielectric substrate has no direct effect on the magnetic field of a microwave signal travelling along the CPW line. For the magnetic field, the CPW is then symmetrical in the plane of the metalization, between the substrate side and the air side. Consequently, currents flowing along parallel paths on opposite faces of each conductor (on the air-side and on the substrate-side) are subject to the same inductance, and the overall current tends to be divided equally between the two faces.

Conversely, the substrate does affect the electric field, so that the substrate side contributes a larger capacitance across the slots than does the air side. Electric charge can accumulate or be depleted more readily on the substrate face of the conductors than on the air face. As a result, at those points on the wave where the current reverses direction, charge will spill over the edges of the metalization between the air face and the substrate face. This secondary current over the edges gives rise to a longitudinal (parallel with the line), magnetic field in each of the slots, which is in quadrature with the vertical (normal to the substrate surface) magnetic field associated with the main current along the conductors.

If the dielectric constant of the substrate is much greater than unity, then the magnitude of the longitudinal magnetic field approaches that of the vertical field, so that the combined magnetic field in the slots approaches circular polarization.[2]

Application in solid state physics

Coplanar waveguides play an important role in the field of solid state quantum computing, e.g. for the coupling of microwave photons to a superconducting qubit. In particular the research field of circuit quantum electrodynamics was initiated with coplanar waveguide resonators as crucial elements that allow for high field strength and thus strong coupling to a superconducting qubit by confining a microwave photon to a volume that is much smaller than the cube of the wavelength. To further enhance this coupling, superconducting coplanar waveguide resonators with extremely low losses were applied.[3][4] (The quality factors of such superconducting coplanar resonators at low temperatures can exceed 106 even in the low-power limit.[5]) Coplanar resonators can also be employed as quantum buses to couple multiple qubits to each other.[6][7]

Another application of coplanar waveguides in solid state research is for studies involving magnetic resonance, e.g. for electron spin resonance spectroscopy[8] or for magnonics.[9]

Coplanar waveguide resonators have also been employed to characterize the material properties of (high-Tc) superconducting thin films.[10][11]

See also

References

  1. ↑ Forman, M. A. (December 2006). "Low-loss LIGA-fabricated coplanar waveguide and filter". Apmc 2006. 12: 905–1907.
  2. 1 2 Wen, Cheng P. (December 1969). "Coplanar Waveguide: A Surface Strip Transmission Line Suitable for Nonreciprocal Gyromagnetic Device Applications". IEEE Trans. Microwave Theory Tech. MTT-17: 1087–1090.
  3. ↑ L. Frunzio; et al. (2005). "Fabrication and Characterization of Superconducting Circuit QED Devices for Quantum Computation". IEEE Transactions on Applied Superconductivity. 15: 860. arXiv:cond-mat/0411708. doi:10.1109/TASC.2005.850084.
  4. ↑ M. Göppl; et al. (2008). "Coplanar waveguide resonators for circuit quantum electrodynamics". J. Appl. Phys. AIP. 104: 113904. arXiv:0807.4094. Bibcode:2008JAP...104k3904G. doi:10.1063/1.3010859.
  5. ↑ A. Megrant; et al. (2012). "Planar superconducting resonators with internal quality factors above one million". Appl. Phys. Lett. 100: 113510. arXiv:1201.3384. Bibcode:2012ApPhL.100k3510M. doi:10.1063/1.3693409.
  6. ↑ M. A. Sillanpää; J. I. Park; R. W. Simmonds (2007-09-27). "Coherent quantum state storage and transfer between two phase qubits via a resonant cavity". Nature. 449 (7161): 438–42. arXiv:0709.2341. Bibcode:2007Natur.449..438S. doi:10.1038/nature06124. PMID 17898762.
  7. ↑ J. Majer; J. M. Chow; J. M. Gambetta; J. Koch; B. R. Johnson; J. A. Schreier; L. Frunzio; D. I. Schuster; A. A. Houck; A. Wallraff; A. Blais; M. H. Devoret; S. M. Girvin; R. J. Schoelkopf (2007-09-27). "Coupling superconducting qubits via a cavity bus". Nature. 449 (7161): 443–447. arXiv:0709.2135. Bibcode:2007Natur.449..443M. doi:10.1038/nature06184. PMID 17898763.
  8. ↑ Y. Wiemann; et al. (2015). "Observing electron spin resonance between 0.1 and 67 GHz at temperatures between 50 mK and 300 K using broadband metallic coplanar waveguides". Appl. Phys. Lett. 106: 193505. arXiv:1505.06105. Bibcode:2015ApPhL.106s3505W. doi:10.1063/1.4921231.
  9. ↑ Kruglyak, V V; Demokritov, S O; Grundler, D (7 July 2010). "Magnonics". Journal of Physics D: Applied Physics. 43 (26): 264001. Bibcode:2010JPhD...43z4001K. doi:10.1088/0022-3727/43/26/264001.
  10. ↑ W. Rauch; et al. (1993). "Microwave properties of YBa2Cu3O7−x thin films studied with coplanar transmission line resonators". J. Appl. Phys. 73: 1866–1872. arXiv:1505.06105. Bibcode:1993JAP....73.1866R. doi:10.1063/1.353173.
  11. ↑ A. Porch; M.J. Lancaster; R.G. Humphreys (1995). "The coplanar resonator technique for determining the surface impedance of YBa2Cu3O7-delta thin films". IEEE Transactions on Microwave Theory and Techniques. 43: 306–314. Bibcode:1995ITMTT..43..306P. doi:10.1109/22.348089.
  • Coplanar waveguide circuits, components and systems (Rainee N. Simons - Wiley series in microwave and optical engineering ; Year 2001 ; ISBN 0-471-16121-7)
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.