Climbing wall

An indoor rock climbing wall in the UK showing moulded features and coloured route markers.

A climbing wall is an artificially constructed wall with grips for hands and feet, usually used for indoor climbing, but sometimes located outdoors. Some are brick or wooden constructions, but on most modern walls, the material most often used is a thick multiplex board with holes drilled into it. Recently, manufactured steel and aluminum have also been used. The wall may have places to attach belay ropes, but may also be used to practise lead climbing or bouldering.

Each hole contains a specially formed t-nut to allow modular climbing holds to be screwed onto the wall. With manufactured steel or aluminum walls, an engineered industrial fastener is used to secure climbing holds. The face of the multiplex board climbing surface is covered with textured products including concrete and paint or polyurethane loaded with sand. In addition to the textured surface and hand holds, the wall may contain surface structures such as indentions (incuts) and protrusions (bulges), or take the form of an overhang, underhang or crack.

Some grips are formed to mimic the conditions of outdoor rock, including some that are oversized and can have other grips bolted onto them.

History

The earliest artificial climbing walls were typically small concrete faces with protrusions made of medium-sized rocks for hand holds. Schurman Rock in Seattle, WA is believed to be the first artificial climbing structure in the United States, constructed in 1939.[1]

The modern artificial climbing wall began in the UK. The first wall was created in 1964 by Don Robinson, a lecturer in Physical Education at the University of Leeds, by inserting pieces of rock into a corridor wall.[2] He went on to found DR International Climbing Walls in 1975, of which he is still Chairman and Executive Director. The first commercial wall was built in Sheffield, traditionally England's centre for climbing due to its proximity to the Peak District. The first indoor climbing gym in the U.S. was established by Vertical World in Seattle, WA in 1987.[3]

Wall types

An inflatable climbing tower

The simplest type of wall is of plywood construction, known colloquially in the climbing community as a 'woody', with a combination of either bolt-on holds or screw on holds. Bolt-on holds are fixed to a wall with iron bolts which are inserted through the hold, which will have specific bolt points, and then fixed into pre-allocated screw-threaded holes in the wall. Screw-on holds are, by contrast, usually much smaller, owing to the nature of their fixing. These holds are connected to the wall by screws which may be fastened anywhere on the wall's surface.

Some other types of walls include slabs of granite, concrete sprayed onto a wire mesh, pre-made fiberglass panels, large trees, manufactured steel and aluminum panels, textured fiberglass walls and inflatables.

In addition to the above, the newest climbing wall to the market is the Rotating Climbing Wall, "The Rock", as it is known is a Rotating, mechanical mobile climbing wall and is a 2 climber wall on which it is impossible to finish. As you climb the wall rotates round to match you climbing up.

Indoor climbing

Indoor climbing is an increasingly popular form of rock climbing performed on artificial structures that attempt to mimic the experience of outdoor rock. The first indoor climbing gym in the U.S. and Canada was established in Seattle in 1987 under the name of Vertical Club, Inc. It is now known as Vertical World, Inc., which has three gyms in the Puget Sound Area - Seattle, Redmond and Everett. The first indoor climbing hall in the world was inaugurated in Bolzano, Italy in 1974.[4]

The proliferation of indoor climbing gyms has increased the accessibility, and thus the popularity, of the sport of climbing. Since environmental conditions (ranging from the structural integrity of the climbing surfaces, to equipment wear, to proper use of equipment) can be more controlled in such a setting, indoor climbing is perhaps a safer and more friendly introduction to the sport. Many rock gyms are settings for birthday parties and youth teams.

The first indoor walls tended to be made primarily of brick leaving little scope for interesting routes, as the steepness of the wall and variety of the hand holds were somewhat limited.[5] More recently, indoor climbing terrain is constructed of plywood over a metal frame, with bolted-on plastic hand and footholds, and sometimes spray-coated with texture to simulate a rock face.

Indoor climbing has also seen an increase in popularity in areas with rainy climates where climbing outdoors is sometimes difficult. Besides offering an alternative during inclement weather, many working adults find that they can get to the gym after work and still climb even though it is too dark outside. In order to improve in any sport, consistent practice is crucial. With the advent of indoor climbing, weather, seasonal difficulties, and busy schedules are less of an obstacle to consistent improvement, and enjoyment of the sport.

Most climbing competitions are held in climbing gyms, making them a part of indoor climbing.

Compared to outdoor climbing

Indoor and outdoor climbing can differ in techniques, style and equipment. Climbing artificial walls, especially indoors, is much safer because anchor points and holds are able to be more firmly fixed, and environmental conditions can be controlled. During indoor climbing, holds are easily visible in contrast with natural walls where finding a good hold or foothold may be a challenge. Climbers on artificial walls are somewhat restricted to the holds prepared by the route setter whereas on natural walls they can use every slope or crack in the surface of the wall. Some typical rock formations can be difficult to emulate on climbing walls.[6]

Construction

Child's wooden climbing wall in Parkend, Forest of Dean, UK

The most common construction method involves bolting resin hand and foot holds onto wooden boards. The boards can be of varying height & steepness (from completely horizontal 'roofs' to near-vertical 'slabs') with a mixture of holds attached. These can vary from very small 'crimps', and 'pinches', and slanted-surfaced 'slopers', to 'jugs', which are often large and easy to hold. This variety, coupled with the ability for the climbs to be changed by moving the holds to new positions on the wall, has resulted in indoor climbing becoming a very popular sport.

Equipment

Proper climbing equipment must be used during indoor climbing.[7] Most climbing gyms lend harnesses, ropes and belay devices. Some also lend climbing shoes and chalk bags. Some climbing gyms require use of chalk balls (as opposed to loose chalk) to reduce chalk dust in the air and chalk spills when a chalk bag is tipped over or stepped on. Reducing chalk in the air helps to avoid clogging ventilation systems and reduces the dust that accumulates on less-than-vertical surfaces.

Routes and grading

Boulder Dash

Holds come in different colours, those of the same colour often being used to denote a route, allowing routes of different difficulty levels to be overlaid on one another. Coloured tape placed under climbing holds is another way that is often used to mark different climbing routes. In attempting a given route, a climber is only allowed to use grips of the designated colour as handholds but is usually allowed to use both handholds and footholds of the designated colour and surface structures and textures of the "rockface" as footholds.

The grade (difficulty) of the route is usually a consensus decision between the setter of the route and the first few people who climb the route. Many indoor climbing walls have people who are assigned to set these different climbing routes. These people are called route setters or course setters. As indoor climbing walls are often used to check the development of climber's ability, climbs are color-coded.

Each gym has a "designated" path to climb known as the "route". Each route is distinguished either by an indicated piece of tape or a monochromatic system of climbing holds. If the route is taped, each hold on the designated route will have the same color tape, indicating which holds to grab or step on. Some newer gyms have converted to the monochromatic system: instead of using colored tape as route indicators, this system uses colored climbing holds. Each monochromatic route is set using holds of a corresponding color; thus, climbers follow the holds of a single color throughout the route.

Route-setting is the design of routes through placing climbing holds in a strategic, technical, and fun way that sets how the route will flow. There are many different techniques involved with setting, and up to 5 levels of certifications are awarded to those qualified. Route setting can be defined as the back bone of indoor climbing; without a great set of routes, a gym cannot easily hope to keep a good hoard of climbers.

See also

References

  1. ↑ http://parkways.seattle.gov/2015/08/27/rock-climbings-history-and-rising-popularity-inspires-seattle-festival/#sthash.WKTjS0gy.dpbs. Missing or empty |title= (help)
  2. ↑ John., White, (2013). The indoor climbing manual. London: Bloomsbury Sport. pp. 9–10. ISBN 9781408186626. OCLC 855536351.
  3. ↑ Edwards, Dolby. "Vertical World History". seattle.verticalworld.com/.
  4. ↑ "SALEWA Cube: Highlight for the Bolzano climbing scene" (PDF). salewa-cube.com. Retrieved 2018-06-18.
  5. ↑ "Scottish Climbing Wall History". Mcofs.org.uk. Retrieved 2013-02-03.
  6. ↑ "What is Indoor Climbing?". Abc-of-rockclimbing.com. 2011-06-02. Retrieved 2013-02-03.
  7. ↑ "Equipment". Alumnus.caltech.edu. Retrieved 2013-02-03.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.