HAL AMCA

Advanced Medium Combat Aircraft
A model of AMCA displayed at Aero India 2013
Role Stealth multirole fighter
National origin India
Manufacturer Hindustan Aeronautics Limited
Designer Aeronautical Development Agency
Defence Research and Development Organisation
Status Under development
Primary users Indian Air Force
Indian Navy

The HAL Advanced Medium Combat Aircraft (AMCA) is an Indian programme of a fifth-generation fighter aircraft. It is being developed by an aerospace industry team which consists of the Aeronautical Development Agency (ADA) as the design firm with manufacturing carried out by Hindustan Aeronautics Limited (HAL) as the primary contractor and main assembly firm.[1] It is a single-seat, twin-engine, stealth all weather multirole fighter aircraft.[2] Feasibility study on AMCA and the preliminary design stage have been completed. The project awaits approval to begin design and development stage.[3][4] The first flight is scheduled to occur in 2032.[5][6]

It is a multirole combat aircraft designed for air superiority, ground attack, bombing, intercepting, strike and other types of roles. It combines supercruise, stealth,[7] advanced AESA radar, supermaneuverability and advanced avionics to overcome and suppress previous generation fighter aircraft along with many ground and maritime defences. It will complement HAL Tejas, the Su-30MKI, and Rafale in the air force service and HAL Naval Tejas and Mikoyan MiG-29K in the naval service. The AMCA is intended to be the successor to the SEPECAT Jaguar, Dassault Mirage 2000 and Mikoyan MiG-27 in the Indian Air Force.[8] The aircraft, along with its naval variants, is intended to provide the bulk of the manned tactical airpower of the Indian Air Force and Navy over the coming decades. AMCA would be the third supersonic jet of Indian origin after the HAL Marut and HAL Tejas.

Development

AMCA Program

The AMCA program evolved out of the Medium Combat Aircraft (MCA) programme, was initiated to fulfil several requirements for a common fighter to replace different types of existing fighters aircraft which included Dassault Mirage 2000 and SEPECAT Jaguar. In October 2008, the Indian Air Force asked the ADA to prepare a detailed project report on the development of an MCA incorporating stealth features.[9]

Our requirement is to look for a fighter aircraft which will be required after 2020 and that aircraft should have all capabilities in the terms of agility, maneuverability, load carrying capacity, low radar cross-section (stealth features), super cruise.

DRDO's chairman VK Saraswat.[10]

In February 2009, ADA director PS Subramanyam said at an Aero-India 2009 seminar that they were working closely with the Indian Air Force to develop a Medium Combat Aircraft. He added that according to the specification provided by the Indian Air Force, it would likely be a 20-ton aircraft and would be powered by two GTX Kaveri engines.[11]

In March 2010, the aircraft was renamed as Advanced Medium Combat Aircraft (AMCA). In April 2010, the Indian Air Force Chief of Air Staff issued the Air Staff requirements (ASR) for the AMCA, which placed the aircraft in the 25-ton category.[2][12][13] The first flight test of the prototype aircraft was scheduled to take place by 2017.[14]

Funding

In October 2010, the Indian Government released ₹100 crore to prepare feasibility studies in 18 months.[15] In November 2010, the ADA sought ₹9,000 crore (approximately €1.5 billion/US$2 billion) of funding for the development of the AMCA.[14] The funding would be utilised to develop two technology demonstrators and seven prototypes.[16] The initial development cost is estimated to be between ₹4,000–5,000 crores to build 3 to 4 flying prototypes.[17][18]

Design phase

The conceptual design of AMCA was carried out till 2015, at which point the general configuration was frozen.[19] Ten design proposals were evaluated with five designs emerging after intensive wind tunnel testing.[2] Proposal of design which included tail were designated with the serial number 3B-01 to 3B-09.[2]

Previous designs

The initial design of the AMCA was a tailess, delta wing aircraft with twin engines.[2] The design was changed to include horizontal and vertical stabilizers in design 38-01. It featured a double delta wing configuration, that was altered in design 38-09 similar to the F-22.[2]

A cancelled wind tunnel model of Medium Combat Aircraft

AMCA's second design proposal was first showcased at Aero India 2009.[20] The design-based stealth features were further optimized by the use of airframe shaping, composite material, edge matching fuselage, RAPs, body conforming antennae and engine bay cooling, RAMs, weapons bay, special coatings for poly-carbonate canopy and other stealth features, the aircraft had a weight of 16–18 tonnes with 2-tonnes of internal weapons and four-tonnes of internal fuel with a combat ceiling of 15-km, max speed of 1.8-Mach at 11-km.[21]

Finalised concept

The aircraft concept was finalized and shown to the Indian Air Force in 2012, after which full-scale development on the project was started.[22] In February 2013, the ADA unveiled a 1:8 scale model at Aero India 2013, to show the finalized proposal.[23][24][25][26]

Project Definition phase

Project Definition commenced from February 2013 to March 2014, started immediately after the design was finalized with intensive development on the finalised design.[27] [28]

In April 2013, the Ministry of Defence had put the project on hold, wanting to make up for the protracted delays incurred by the ADA and DRDO's labs and establishments during the development of the HAL Tejas.[29][30] According to the Defence of Ministry, "this decision was taken recently to let the ADA and DRDO's Labs to focus on the HAL Tejas."[29][31][32] The AMCA design team led by Dr. A K Ghosh had completed low-speed wind tunnel testing, supersonic wind tunnel testing and Radar Cross-Section (RCS) testing between 2008 and 2014 during which all the five design proposals underwent intensive air flow testing, design development and improvements.[33][34]

Design research and development of the finalized design was completed by NAL from October 2012 to September 2014. The R&D efforts led to the current configuration of the aircraft and a structurally efficient wings layout with four bending attachment brackets and two shear attachment brackets. For the AMCA, structural design, analysis and size optimization was carried out to cater for all critical symmetric and un-symmetric load cases. Finite element models were built separately for each of the fuselage segments and then integrated to build a full fuselage finite element model which also incorporated a new design for the air intakes, a key element to maintain the aircraft's stealth characteristics.[35] Project definition phase was fully completed by February 2014.[36]

ETMD phase

The Engineering Technology & Manufacturing Development (ETMD) phase was started on 7 January 2014 when work on AMCA had again commenced after HAL Tejas attained IOC, and it was announced that the AMCA will be developed by 2018.[23][37][38][39] The configuration was finalised in 2014, with the first flight scheduled for 2018.[40][41][42][43] The product design work of the AMCA was started by the DRDO and the work on the prototype as the part of proof of concept stage was expected to be ready in 2018.

On 7 February 2014 DRDO Director Dr Tamilmani told reporters on the sidelines of the three-day international meet on Product Life Cycle Modelling, Simulation and Synthesis (PLMSS) at VIT university,’ he said the aircraft would be equipped with twin engines with supercruise power and for the first time it would be using the stealth technology to 'hide' from radar surveillance.[44] At a seminar ahead of the Aero India show, DRDO's chairman Dr. V.K Saraswat said that Indian private sector firms are also participating and offering support in the program.[1]

At Aero India 2015, Tamilmani confirmed that the work on three major technological issues which includes Thrust Vectoring and supercruising engine, AESA radar and stealth technology is going on full swing and availability of the technology on the aircraft will occur on schedule.[45] In 2015, 700 ADA employees were working on the project along with 2,000 employees of DRDO and 1,000 employees of HAL supported by over 500 employees of subcontractors of both Indian and foreign firms. On 7 March 2015 a Memorandum of Understanding (MoU) through Government to Government (G-to-G) route between India and Russia was signed in which various Russian firms agreed to help Indian firms in various technological fields which included the Gas Turbine Research Establishment (GTRE) entered in a joint-venture with Klimov for the development of Three-Dimensional Thrust Vectoring (TDTVC), Electronics and Radar Development Establishment (LRDE) with Tikhomirov Scientific Research Institute of Instrument Design (TSRIID) for the AESA Radar and ADA with the Sukhoi for stealth technology and other various key technological fields.[46][47] In March 2015 Boeing and Lockheed Martin offered to help HAL and DRDO in the field of stealth, thrust vectoring and other key technologies.[48] Work on various technology was carried by various establishment of DRDO, ADA and HAL which included stealth, engine, three-dimensional thrust vectoring, AESA radar, internal weapons bay, serpentine air intakes and all other major avionics.[33][49][50][51][52] According to Deputy Air Marshall Sinha "To provide adequate time to Indian industries to develop required capabilities, the armed forces will soon come out with a list of technologies of interest... underlining that these efforts are expected to synergise indigenous development of advanced aerospace systems."[53] Saab AB made an offer for participating in the programme on its own and also helping and sharing many technical information and data for development in the AMCA programme.[54][55] Saab's head of aeronautics division Ulf Nilsson, pushed the idea of Saab taking part in the programme. [56][57]

Engine development

Engine development on K 9 and K 10 started in August 2012 by GTRE. A tender of joint venture on development of the engine was issued to engine manufacturers in 2015 for a foreign partner to help in developing the engine by combining both Kaveri engine technology with the joint-venture partners engine to create a 110–125 KTN thrust engine. On 19 February 2015 at Aero India 2015 Tamilmani told reporters that a tender of joint venture on development of the engine was issued to General Electric, Rolls Royce, Snecma, Eurojet, NPO Saturn to use current engine technology by combining Kaveri engine technology with JV engine to produce an engine capable of producing thrust of 110–125 kN.[58][59][60][61] Tamilmani confirmed the possibility of combining Kabini Core-engine with joint venture partner core engine i.e. with the EJ 200, Snecma M88, NPO Saturn AL-31-117 or General Electric F414 to produce 110–125 KN of thrust. France made an unsolicited call to help in development of AMCA's engine with full access to the Snecma M88 engine and other key technology, while United States has offered full collaboration in the engine development with full access to the GE F-414 and F-135.[62][63] During U.S President Barack Obama's visit on 25–27 January he pointed out a possibility of joint-development of a Hot-Engine, an advanced variable cycle engine capable of performing in hot weather conditions like those of India.[64] Rolls-Royce was also pushing a deal for a joint venture engine by offering the co-development of a new engine based on the Kaveri and EJ2XX engines. In November, during the visit of Indian Prime Minister Narendra Modi to UK, Rolls-Royce again pushed the EJ2XX engine in a joint development proposal despite favouritism towards General Electric for a JV programme. In December U.S government made sign of support for full fledge transfer of technology including many classified information of F-414 engine in joint venture engine development.[65][66][67] During Indian defence minister Manohar Parrikar's visit to the United States, the U.S defence secretary Ash Carter and Parrikar discussed the matter of joint development of the engine.[68][69]

Modular approach

We are also channelising all of R&D resources in development of Advanced Medium Combat Aircraft (AMCA) in a time-bound manner with an open mind to seek consultancy where required, Aeronautical Development Agency is in the process of evolving a methodology to involve private Indian industries in a big way in the development and manufacture of AMCA.

Deputy Chief of Air Staff Air Marshal S B sinha.[70]

AMCA uses a modular approach in its design, development and production. Most of the assembly and equipment are outsourced to both private firms and public sector undertakings. A consortium of more than 140 firms are taking part in the programme. This is a major departure from HAL's previous fighter aircraft, the HAL Tejas, which used in-house production with minor outsourcing. Additionally, AMCA uses a modular method of production in order to reduce the time required for development and production. This method of production also results in increased on-schedule delivery resulting in an increased rate of production. Firms participating in the programme include HAL as the prime contractor, while sub assembly is carried out by Tata Advanced Systems, Reliance Aerospace, Larsen & Toubro, and Godrej Aerospace.[2] Sub-assembly carried out by sub-contractors includes the wings, tail, tail fins, raydome, rear fuselage and landing gear.[2]

The development and production of the aircraft is carried out by four types of firm:

  • Design team – ADA as the prime designer and developer of the aircraft.
  • Core team – DRDO agencies carrying out primary development.
  • External agencies – Various institutes, universities and other firms of both domestic and foreign origin.
  • Manufacturing team – Manufacturers and assemblers.[2]

Prototype

In January 2019, two technology demonstrator and four prototype are scheduled to go under various type of testing, analysis and development during testing phase.[71][72][73]

On 4, April 2018 Defence Minister Nirmala Sitharaman while answering an written reply in the Lok Sabha summer Session said the feasibility study of the programme had already been completed and the programme has already been given go ahead by the IAF to the relevant agencies associated with the programme lead by ADA and DRDO to initiate AMCA Technology Demonstration phase before launching full Scale engineering development phase[74]

Design

Overview

The AMCA is a multirole fighter aircraft, with shoulder mounted diamond shaped trapezoidal wings, a profile with substantial area-ruling to reduce drag at transonic speeds, and an all-moving Canard-Vertical V-tail with large fuselage mounted Tail-wing.[2] Flight control surfaces include leading and trailing-edge flaps, ailerons, rudders on the canted vertical stabilizers, and all-moving tailplanes; these surfaces also serve as Air brakes. The cockpit features a single seat configuration which is placed high, near the air intakes and wings of the aircraft to provide good visibility to the pilot with a single bubble canopy construction.[2] The aircraft features a tricycle landing gear configuration with a nose landing gear leg and two main landing gear legs. The weapons bay is placed on the underside of the fuselage between the nose and main landing gear. The AMCA is designed to produce a very small radar cross-section, to accomplish this it features serpentine shaped air-intakes to reduce radar exposure to the fan blade which increases stealth, uses an internal weapons bay and features the use of composites and other materials.[2] The flight control surfaces are controlled by a central management computer system. Raising the wing flaps and ailerons on one side and lowering them on the other provides roll.

A leading-edge root extension (LERX), which is a small fillet, is situated on the front section of the intake and wings of the aircraft. It has a typically roughly rectangular shape, running forward from the leading edge of the wing root to a point along the fuselage. Also, the AMCA has an In-flight refueling (IFR) probe that retracts beside the cockpit during normal operation.[2]

Airframe

Stressed ducts in s-shape are locked with airframe with the loaded bulkheads which are made of composite materials spanning the aircraft from air intake to engine shafts.[2] The radome which holds radar is made of advance composite and construction, which result in allowing only the operating frequencies of the mated radar to transmit from the dome, while blocking other radars.[2]

Flight surfaces and controls

Since the AMCA is a relaxed static stability design, it is equipped with a quadruplex digital fly-by-optics flight control system to ease pilot handling. The AMCA's aerodynamic configuration is based on a diamond shaped trapezoidal-wing layout with shoulder-mounted wings. Its control surfaces are electro hydraulically actuated and digitally controlled using fiber-optic cables. The wing's outer leading edge incorporates three-section slats, while the inboard sections have additional slats to generate vortex lift over the inner wing and high-energy air-flow along the tail fin to enhance high-angle of attack stability and prevent departure from controlled flight. The wing trailing edge is occupied by two-segmented elevons to provide pitch and roll control. The only empennage-mounted control surfaces are the Pelikan tail with single-piece rudder which includes two airbrakes located in the upper rear part of the Pelikan tail, one each on either side of the tail. The AMCA feature a highly evolved integrated control laws for flight, propulsion, braking, nose-wheel steering and fuel management and adaptive neural networks for fault detection, identification and control law reconfiguration.[75] Flights controls of the aircraft are both highly integrated and independent of each other which includes flight controls, engine controls, brake and landing controls, and other systems this is possible due the active controls gears systems (ACGS).[2]

The digital FBW system of the aircraft employs an advance next-generation distributed digital flight control computer (DDFCC) made by ADE comprising four computing channels, each with its own independent power supply and all housed in differently placed LRU.[76] The DFCC receives signals from a variety of sensors and pilot control stick inputs, and processes these through the appropriate channels to excite and control the elevons, rudder and leading edge slat hydraulic actuators. DFCC provides raising the wing flaps and ailerons on one side and lowering them on the other provided roll. The Pelikan-tail fins are angled at 27 degrees from the vertical. Pitch is mainly provided by rotating these pelikan-tail fins in opposite directions so their front edges moved together or apart. Yaw is primarily supplied by rotating the tail fins in the same direction. The AMCA is designed for superior high Angle of attack (AoA) performance. Deflecting the wing flaps down and ailerons up on both sides simultaneously provided for Aerodynamic braking.[2]

Propulsion

AMCA is a twin-engined aircraft which is powered by two GTRE K 9 + or K 10 engine which are successor to the troubled Kaveri engine.[77] The K 10 Program is a joint venture partnership with a foreign engine manufacturer. K 10 program engine will be final production standard Kaveri engine and shall have less weight and more reheat thrust along with certain other changes to meet the original design intent.[78] Both the engines are designed by ADA and developed by GTRE.[7] Full scale development of the K 9 and K 10 engine would be completed by 2019.[47] while AMCA Test Demonstrator would be powered by an existing 90 kN thrust engine.[64]

[79]“The AMCA will feature geometric stealth and will initially fly with two GE-414 engines." it can be replaced with Indian power plant once developed. The first flight in 2032.

The K 9 + and K 10 engines are designed to supercruise with a speed of Mach 1.82 with both engines.[2][80] The aircraft is projected to have a maximum speed of over Mach 2.5, with a maximum takeoff weight of 60,000 lb (29,000 kg).

Stealth and radar signature

The AMCA is designed to be difficult to detect by radar and other electronic measures due to various features to reduce radar cross-section include airframe shaping such as planform alignment of edges, fixed-geometry serpentine inlets that prevent line-of-sight of the engine faces from any exterior view, use of radar-absorbent material (RAM), and attention to detail such as hinges and pilot helmets that could provide a radar return. Efforts have been made to minimise radio emissions and both the infrared signature and acoustic signature as well as reduced visibility to the naked eye.[81] Alignment of wings, tail, flaps and other edges increases radar and visually stealthe.[2]

Radar absorbing structures and radome, body conformal antennae surface hard aperture, flush air data sensors and frequency selective surface (FSS) radome are used to reduce radar detection.[82] Stealth ability is enhanced by the use of microelectromechanical systems (MEMS) and nanoelectromechanical systems (NEMS) during the construction of the airframe and in the airframe and instruments.[2] AMCA's design prevents detection of the aircraft from L band, C band and X band radars.[2] The aircraft's thrust vectoring nozzle reduces infrared emissions to mitigate the threat of infrared homing surface-to-air or air-to-air missiles. Additional measures to reduce the infrared signature include special paint and active cooling of leading edges to manage the heat build up from supersonic flight.

Armament and standards

Image of Astra

The AMCA features an internal weapons bay, but a non-stealthy version with external pylons is also planned.[19] The aircraft is planned to be equipped with beyond visual range missiles, close combat missiles, standoff weapons, precision weapons and laser guided bombs.[83]

Avionics and equipment

The aircraft's avionics suite will have IRST and advance situational oriented electronic warfare systems and all aspect radar warning receiver (RWR), Self-Protection Jammer(SPJ), CMOS, laser warning receiver (LWR), missile warning suite.[84]

Defence Electronics Application Laboratory (DEAL) has designed and developed a next-generation network-centric aircraft management system (including weapons) including various features such as data fusion, Cooperative Engagement Capability, decision aids, integrated modular avionics, and intern signature control with sharpening for low observability.[2][85] The aircraft will use integrated modular avionics for real time computing, and the fibre optic cables used on the aircraft feature photonic crystal fibres technology for faster exchange of data and information.[52] Unlike the HAL's previous fighter aircraft, the Tejas, which has a digital flight-control computer and hydraulic controllers, the AMCA has a distributed processing system employing fast processors and smart subsystems and will be electronically controlled via a "central computational system connected internally and externally on an optic-fibre channel by means of a multi-port connectivity switching module". This results in using the IEEE-1394B-STD a departure from MIL-STD-1553B databus standard.[86]

Radar and sensors

AMCA would be equipped with an AESA radar mounted on a mechanically steerable mount.[2] An onboard condition monitoring system is planned to be included in the AMCA.[87]

Cockpit

The AMCA's cockpit features a panoramic active-matrix display, with the switches, bezels and keypads replaced with a single large multi-functional touch screen interface supported by voice commands (Also the cockpit will be fully made by composite or glass) .[75]

Projected Specifications

Data from Jane's All the World's Aircraft[88]

General characteristics

Performance

Armament

  • Guns: 23 mm GSh-23 cannon
  • Hardpoints: 3 under each wing, 2 tandem pairs under-fuselage for a total of 10
  • Missiles: BrahMos NG[34]

See also

Related development

Aircraft of comparable role, configuration and era

Related lists

References

Notes

    References

    1. 1 2 "New Design For Indian Advanced Medium Combat Aircraft". Aviation Week & Space Technology. Aviation Week. 4 March 2013. Retrieved 18 August 2013.
    2. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Abhijit Iyer-Mitra and Pushan Das. "The Advanced Medium Combat Aircraft:A Technical Analysis" (PDF). Observer Research Foundation.
    3. ↑ Pandit, Rajat (8 January 2015). "Make-in-India: Plan to develop 5th-generation fighter aircraft". The Times of India. TNN.
    4. ↑ A Raghu Raman (4 January 2017). "India to make stealth fighter". The Asian Age.
    5. ↑ Peri, Dinakar (2018-08-19). "India building new fighter jet". The Hindu. ISSN 0971-751X. Retrieved 2018-08-22.
    6. 1 2 Waldron, Greg (17 February 2017). "AERO INDIA: New Delhi continues work on stealthy AMCA". FlightGlobal.
    7. 1 2 "Scientists face uphill task developing India's first 5th generation fighter". Bangalore Mirror. Bangalore Mirror Bureau. 12 February 2015.
    8. ↑ Shukla, Ajai (5 October 2015). "Indian Air Force chief expects full strength of 42 squadrons by 2027". Business Standard.
    9. ↑ Rao, Radhakrishna (6 October 2008). "India reveals plan to develop indigenous medium fighter". Flight International. Archived from the original on 10 February 2009.
    10. ↑ "India to build its own stealth fighter jet-IndiaNews – IBNLive Mobile". IBNlive. 7 August 2011.
    11. ↑ "After LCA it's Medium Combat Aircraft". The Hindu. 5 February 2009. Retrieved 17 November 2010.
    12. ↑ "India's Indigenous 5th-Gen Combat Plane to Boast Of Condition Monitoring Systems". Defence Now. Archived from the original on 10 December 2013. Retrieved 5 December 2013.
    13. ↑ "Login". aviationweek.com. Retrieved 6 April 2015.
    14. 1 2 "ADA seeks $2 bn for advanced medium combat aircraft". Business Standard. Retrieved 27 July 2012.
    15. ↑ Y. Mallikarjun (21 November 2010). "Plans for Advanced Medium Combat Aircraft". The Hindu. Archived from the original on 24 November 2010.
    16. ↑ "India Advances Indigenous Stealth Fighter Effort". Aviation Week & Space Technology. Retrieved 6 April 2015.
    17. ↑ Jha, Saurav (27 December 2014). "A note on India's Advanced Medium Combat Aircraft (AMCA) project". IBNLive. Archived from the original on 28 July 2015.
    18. ↑ Lt General P.C. Katoch (Retd) (February 2015). "Stealth in the skies". SP's MAI. Retrieved 16 November 2017.
    19. 1 2 Perrett, Bradley; Menon, Jay (23 February 2017). "India's AMCA Fighter Targets Mid-2020s First Flight". Aerospace Daily & Defense Report. Aviation Week. Retrieved 16 November 2017. (registration required)
    20. ↑ "The Telegraph – Calcutta (Kolkata) – Frontpage – On drawing board: desi stealth fighter". telegraphindia.com. Retrieved 6 April 2015.
    21. ↑ Reed Business Information Limited. "AERO INDIA: Roadmap revealed for Medium Combat Aircraft". flightglobal.com.
    22. ↑ Surya Gangadharan (7 August 2011). "India to build its own stealth fighter jet". IBNlive.com. Retrieved 8 August 2011.
    23. 1 2 "AMCA to be studded with new-age technologies". Indian Express. 1 February 2013. Retrieved 5 February 2013.
    24. ↑ "유용원의 군사세계 > 무기토론방". chosun.com. Retrieved 6 April 2015.
    25. ↑ "Actualites". defense.gouv.fr. Retrieved 6 April 2015.
    26. ↑ "Login". aviationweek.com. Retrieved 6 April 2015.
    27. ↑ http://www.idsa.in/system/files/monograph33.pdf
    28. ↑ "VK Saraswat expresses concerns over raising FDI cap in defence". dna. 17 May 2013. Retrieved 16 February 2016.
    29. 1 2 NC Bipindra (14 April 2013). "Tejas grounds Medium Combat Aircraft project". The New Indian Express. Retrieved 22 April 2013.
    30. ↑ Siddiqui, Huma (10 May 2013). "AMCA for IAF on hold due to Light Combat Aircraft". Financial Express. Retrieved 3 November 2015.
    31. ↑ 5th generation AMCA on backburner – SP's MAI. Spsmai.com (19 August 2014). Retrieved on 2015-11-03.
    32. ↑ "Priority re think on Project AMCA – SP's MAI". spsmai.com. Retrieved 6 April 2015.
    33. 1 2 "OneIndia Exclusive: India's stealth fighter dream moves towards reality". www.oneindia.com.
    34. 1 2 Krishnan M, Anantha (19 February 2015). "OneIndia Exclusive: Hypersonic, next-gen missiles on BrahMos' wishlist: Mishra". OneIndia.
    35. ↑ "Stealth in the skies – SP's MAI". spsmai.com. Retrieved 6 April 2015.
    36. ↑ "AMCA announcement at Aero India 2015? – SP's MAI". spsmai.com. Retrieved 6 April 2015.
    37. ↑ "AMCA will be completed by 2018". The New India Express. 7 January 2014. Retrieved 11 January 2014.
    38. ↑ "Work On India's Stealth Aircraft Project To Accelerate". defenseworld.net.
    39. ↑ "The Advanced Medium Combat Aircraft: A Technical Analysis". ORF – Ideas. Forums. Leadership. Impact.
    40. ↑ "Advanced medium combat aircraft first flight likely in 2020", Flight global, 7 February 2013
    41. ↑ "'India to Launch Advanced Medium Combat Aircraft in Another 5 Years'". The New Indian Express.
    42. ↑ "Login". aviationweek.com. Retrieved 6 April 2015.
    43. ↑ "Login". aviationweek.com. Retrieved 6 April 2015.
    44. ↑ "'Advanced Medium Combat Aircraft by 2018'". The New Indian Express.
    45. ↑ "Development of indigenous AMCA on track". The Hindu: Mobile Edition.
    46. ↑ SP's-Aviation. "Russia to partner in AMCA Technologies". sps-aviation.com.
    47. 1 2 Peri, Dinakar (20 February 2015). "Development of indigenous AMCA on track". The Hindu.
    48. ↑ "DRDO in talks with Boeing, Lockheed Martin for UAV". The Hindu Business Line : Mobile Edition.
    49. ↑ "AMCA to be developed in 12 15 years–SP's MAI". spsmai.com. Retrieved 6 April 2015.
    50. ↑ "Future Aircraft Low Observable Progress? – SP's MAI". spsmai.com. Retrieved 6 April 2015.
    51. ↑ "India Explores Low-Observable Aircraft Technologies". aviationweek.com. Retrieved 6 April 2015.
    52. 1 2 Krishnan M, Anantha (19 February 2015). "How PM Modi's Make in India will change the aerospace and defence sector". OneIndia.
    53. ↑ "DEFENCE 2 LAST". Retrieved 16 February 2016.
    54. ↑ "Reliance Defence buys Saab's stake in Pipavav Defence". Retrieved 16 February 2016.
    55. ↑ "Saab offers Gripen fighter jets under 'Make in India' with 'full control'". The Hindu: Mobile Edition. Retrieved 16 February 2016.
    56. ↑ "Saab offers Gripen fighter jets under Make in India with". Retrieved 16 February 2016.
    57. ↑ "IAF modernisation plan: Saab offers Gripen fighter jets under 'Make in India' with full control". The Economic Times. PTI. Retrieved 16 February 2016.
    58. ↑ Shukla, Ajai (29 January 2013). "DefenceMin goes global in search for Kaveri partner". Business Standard.
    59. ↑ Shukla, Ajai (20 February 2015). "Top officials provide glimpse of future air force". Business Standard.
    60. ↑ "Make-in-India: Plan to develop 5th-generation fighter aircraft". timesofindia.com.
    61. ↑ Pandit, Rajat (8 January 2015). "Make-in-India: Plan to develop 5th-generation fighter aircraft". The Times of India. TNN.
    62. ↑ "Low-altitude launch of Nirbhay missile in April". Deccan Herald.
    63. ↑ "Design Of India's AMCA Fighter Fixed, Budget Next". aviationweek.com. Retrieved 6 April 2015.
    64. 1 2 Vijainder K Thakur. "Thum! Kaun Aata Hai?". thumkar.blogspot.in.
    65. ↑ Shukla, Ajai (12 December 2015). "US to help India develop engine for Gen-5 fighter". Business Standard. Retrieved 16 February 2016.
    66. ↑ "US to help India make engine for next combat jet". www.hindustantimes.com. Retrieved 16 February 2016.
    67. ↑ "Jet Engine Technology a Top Priority in India-US Talks". Defense News. 10 December 2015. Retrieved 16 February 2016.
    68. ↑ "Maiden visit of Parrikar to US – SP's MAI". Retrieved 16 February 2016.
    69. ↑ "Carter, Parrikar Pledge Expanded US-Indian Relations". Defense News. 12 December 2015. Retrieved 16 February 2016.
    70. ↑ "Indian air force support for India's Advanced Medium Combat". freepressjournal.
    71. ↑ DRDO in talks with foreign cos for advanced fighter jet engine | Brahmand News Archived 16 March 2015 at the Wayback Machine.. Brahmand.com (20 February 2015). Retrieved on 2015-11-03.
    72. ↑ "India, Russia close in on fifth generation fighter". www.tribuneindia.com. Retrieved 16 February 2016.
    73. ↑ "DRDO in talks with foreign companies for advanced fighter jet engine". dna. 18 February 2015. Retrieved 16 February 2016.
    74. ↑ https://economictimes.indiatimes.com/news/defence/india-working-on-developing-an-advanced-medium-combat-aircraft/articleshow/63617345.cms&ved=0ahUKEwi2_aq9tN_cAhVLP48KHcXpALAQqQIIQCgBMAU&usg=AOvVaw0B2labwqoZv43yPvnih8fJ
    75. 1 2 "The IAF s Generation Dream – SP's Show News". spsshownews.com.
    76. ↑ "Will AMCA Be India's Last Manned Fighter Jet Programme? – SP's MAI". spsmai.com. Retrieved 6 April 2015.
    77. ↑ "AERO INDIA: Advanced medium combat aircraft first flight likely in 2020". Flightglobal.com. Retrieved 16 February 2016.
    78. ↑ "Kaveri engine gathers momentum". Frontier India. Archived from the original on 18 December 2015. Retrieved 6 February 2015.
    79. ↑ Peri, Dinakar (2018-08-19). "India building new fighter jet". The Hindu. ISSN 0971-751X. Retrieved 2018-08-20.
    80. ↑ Madhumati D. S. (15 February 2015). "New fighter plane engine to be upgraded". The Hindu.
    81. ↑ "The Hindu News Update Service". Hindu.com. 13 February 2009. Retrieved 21 October 2010.
    82. ↑ "AMCA to be studded with new-age technologies". The New Indian Express. Retrieved 16 February 2016.
    83. ↑ "Medium Combat Aircraft". MCA Handouts at AI-09. Aeronautical Development Agency. 13 February 2009. Archived from the original on 23 October 2009. Retrieved 30 September 2009.
    84. ↑ "Fifth Gen flavour at Aero India – SP's Show News". Retrieved 16 February 2016.
    85. ↑ Anantha Krishnan M. (AK). "Tarmak007 – A bold blog on Indian defence: Express Exclusive – India's AMCA will be studded with new-age technologies – Silent R& work going on in DRDO, CSIR, IIT & private labs". tarmak007.blogspot.in.
    86. ↑ Karnozov, Vladimir (13 June 2013). "Indian 'Home-Grown' AMCA, An Alternative To FGFA". AIN Online. Retrieved 5 December 2013.
    87. ↑ S. Anandan (19 May 2016). "DRDO developing onboard equipment monitoring system for submarines". The Hindu. Retrieved 17 November 2017.
    88. ↑ Jackson, Paul; Peacock, Lindsay; Bushell, Susan; Willis, David; Winchester, Jim, eds. (2016–2017). "India". IHS Jane's All the World's Aircraft: Development & Production. Couldson. p. 297. ISBN 978-0710631770.
    Flight videos and photos
    This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.