.223 Remington

.223 Remington
A variety of .223 Remington cartridges and a .308 Winchester (right) for comparison. Bullets in .223 cartridges (left to right): Montana Gold 55 grain full metal jacket, Sierra 55 grain Spitzer boat tail, Nosler/Winchester 55 grain combined technology, Hornady 60 grain V-Max, Barnes 62 grain Tipped Triple-Shock X, Nosler 69 grain hollow point boat tail, Swift 75 grain Scirocco II.
Type Rifle
Place of origin United States
Production history
Designer Remington Arms
Designed 1962
Produced 1964–present
Variants .223 Ackley Improved, 5.56×45mm NATO
Specifications
Parent case .222 Remington
Case type Rimless, bottleneck
Bullet diameter 0.224 in (5.7 mm)
Neck diameter 0.253 in (6.4 mm)
Shoulder diameter 0.354 in (9.0 mm)
Base diameter 0.376 in (9.6 mm)
Rim diameter 0.378 in (9.6 mm)
Rim thickness 0.045 in (1.1 mm)
Case length 1.76 in (45 mm)
Overall length 2.26 in (57 mm)
Rifling twist 1 in 12 inch (military style rifles use 1:7 to 1:10 to stabilize longer bullets)
Primer type Small rifle
Maximum pressure (SAAMI) 55,000 psi (380 MPa)
Maximum pressure (CIP) 62,366 psi (430.00 MPa)
Maximum CUP 52000 CUP
Ballistic performance
Bullet mass/type Velocity Energy
36 gr (2 g) JHP 3,750 ft/s (1,140 m/s) 1,124 ft⋅lbf (1,524 J)
55 (3.5 g) Nosler ballistic tip 3,240 ft/s (990 m/s) 1,282 ft⋅lbf (1,738 J)
60 (3.9 g) Nosler partition 3,160 ft/s (960 m/s) 1,330 ft⋅lbf (1,800 J)
69 (4.48 g) BTHP 2,950 ft/s (900 m/s) 1,333 ft⋅lbf (1,807 J)
77 (5 g) BTHP 2,750 ft/s (840 m/s) 1,293 ft⋅lbf (1,753 J)
Test barrel length: 24 inches (61 cm)
Source(s): [1][2]

The .223 Remington (.223 Rem) is a rifle cartridge. It started as the .222 Special and was renamed .223 Remington. It is commercially loaded with 0.224 inch (5.7 mm) diameter jacketed bullets, with weights ranging from 35 to 85 grains (2.27 g to 5.8 g), with the most common loading by far being 55 grains (3.6 g). Ninety and ninety-five grain Sierra Matchking bullets are available for reloaders.[3] The .223 Rem was first offered to the civilian sporting market in December 1963 in the Remington 760 rifle.[4] In 1964 the .223 Rem cartridge was adopted for use in the Colt M16 rifle which became an alternate standard rifle of the U.S. Army. The military version of the cartridge uses a 55 gr full metal jacket boat tail design and was designated M193. In 1980 NATO modified the .223 Remington into a new design which is designated 5.56×45mm NATO type SS109.[5]

History

From left: .222 Remington, .223 Remington and .222 Remington Magnum

The development of the cartridge which eventually became the .223 Remington was intrinsically linked to the development of a new lightweight combat rifle. The cartridge and rifle were developed by Fairchild Industries, Remington Arms and several engineers working toward a goal developed by U.S. Continental Army Command (CONARC). Early development work began in 1957. A project to create a small caliber high velocity (SCHV) firearm was created. Eugene Stoner of ArmaLite was invited to scale down the AR-10 (7.62 mm) design. Winchester was also invited to participate.[4][5] The parameters requested by CONARC were:

  • .22 caliber
  • Bullet exceeding supersonic speed at 500 yards [4][5]
  • Rifle weight 6 lbs
  • Magazine capacity of 20 rounds
  • Select fire for both semi-automatic and fully automatic use
  • Penetration of US steel helmet one side, at 500 yards
  • Penetration of .135" steel plate at 500 yards
  • Accuracy and ballistics equal to M2 ball ammunition (.30-06 M1 Garand)
  • Wounding ability equal to the M1 Carbine[5]

Springfield Armory's Earle Harvey lengthened the .222 Remington cartridge case to meet the requirements. It was then known as the .224 Springfield. Concurrently with the SCHV project Springfield armory was developing a 7.62 mm rifle. Harvey was ordered to cease all work on the SCHV to avoid any competition of resources.

Eugene Stoner of ArmaLite (a division of Fairchild Industries) had been advised to produce a scaled down version of the 7.62 mm AR-10 design. In May 1957 Stoner gave a live fire demonstration of the prototype of the AR-15 for General Wyman. As a result, CONARC ordered rifles to test. Stoner and Sierra Bullet's Frank Snow began work on the .222 Remington cartridge. Using a ballistic calculator they determined that a 55 grain bullet would have to be fired at 3,300 ft/s to achieve the 500 yard performance necessary.[5]

Robert Hutton (technical editor of Guns and Ammo magazine) started development of a powder load to reach the 3,300 ft/s goal. He used DuPont IMR4198, IMR3031 and an Olin powder to work up loads. Testing was done with a Remington 722 rifle with a 22" Apex barrel. During a public demonstration the round successfully penetrated the US steel helmet as required, but testing showed chamber pressures to be excessively high.[4][5]

Stoner contacted both Winchester and Remington about increasing the case capacity. Remington created a larger cartridge called the .222 Special. This cartridge is loaded with DuPont IMR4475 powder.[5]

During parallel testing of the T44E4 (future M14) and the AR-15 in 1958 the T44E4 experienced 16 failures per 1,000 rounds fired compared to 6.1 for the AR-15.[5] Because of several different .222 caliber cartridges which were being developed for the SCHV project, the .222 Special was renamed .223 Remington. In May 1959 a report was produced stating that five to seven man squads armed with AR-15 rifles have a higher hit probability than 11 man squads armed with the M-14 rifle. At an Independence Day picnic air force general Curtis Le May tested the AR-15 and was very impressed with it. He ordered a number of them to replace M2 carbines that were in use by the air force. In November of that year, testing at Aberdeen Proving Ground showed the AR-15 failure rate had declined to 2.5/1,000, resulting in the AR-15 being approved for air force trials.[5]

In 1961 a marksmanship testing compared the AR-15 and M-14. 43 % of AR-15 shooters achieved Expert while only 22 % of M-14 rifle shooters did. Le May ordered 80,000 rifles.[5]

In the spring of 1962 Remington submitted the specifications of the .223 Remington to the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI). In July operational testing ended with a recommendation for adoption of the AR-15 rifle chambered in .223 Remington.[5]

In September 1963 the .223 Remington cartridge was officially accepted and named "Cartridge, 5.56 mm ball, M193". The specification included a Remington-designed bullet and the use of IMR4475 powder which resulted in a muzzle velocity of 3,250 ft/s and a chamber pressure of 52,000psi.[5] The .223 Remington was ballistically between the .222 Remington and the .222 Remington Magnum. It emerged from the .224 Springfield. The popularity of .223 Remington was so great that in the US it virtually eliminated the chambering of new firearms in .222 Remington and .222 Remington Magnum which included both semi-automatic and bolt (manual) action firearms. Outside the US and in areas in Europe where military chamberings are restricted, the .222 Remington remained popular, filling the same market niche.

Cartridge dimensions

The .223 Remington has a 28.8 grain (1.87 ml H2O) cartridge case capacity.[6]

.223 Remington maximum C.I.P. cartridge dimensions. All sizes in millimeters (mm).[7]

Americans would define the shoulder angle at alpha/2 = 23 degrees. The common rifling twist rate for this cartridge is 305 mm (1 in 12 in), 6 grooves, Ø lands = 5.56 millimetres (0.219 in), Ø grooves = 5.69 millimetres (0.224 in), land width = 1.88 millimetres (0.074 in) and the primer type is small rifle.

According to the official C.I.P. (Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives) rulings the .223 Remington can handle up to 430.00 MPa (62,366 psi) Pmax piezo pressure. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of this maximum C.I.P. pressure to certify for sale to consumers.[7] This means that .223 Remington chambered arms in C.I.P. regulated countries are currently (2016) proof tested at 537.50 MPa (77,958 psi) PE piezo pressure. This is equal to the NATO maximum service pressure guideline for the 5.56×45mm NATO cartridge.

The SAAMI pressure limit for the .223 Remington is set at 379.212 MPa (55,000 psi), piezo pressure.[8][9] Remington submitted .223 Remengton specifications to SAAMI in 1964.[5] The original diagrams use English Inch measurements.

Rifling in .223 Remington

Rifling is expressed as a ratio. A 1 in 12" ratio means that rifling is cut so that the bullet rotates 360° after having traveled 12". This is expressed as 1:12 spoken as 1 in 12 inches. Rifling must match the bullet design (length, weight and projectile shape) which a shooter intends to use in order to maintain accuracy.

The .223 Remington is one of the most common rifle cartridges in use in the United States, being widely used in two types of rifles:

The Sturm, Ruger & Co. AR-556 has rifling at 1:8. Their Mini-14 rifles have rates of 1:9. Ruger's American rifle bolt action is also in 1:8.[10] Smith and Wesson in their M&P15 also uses 1:7.[11] The 5.56 mm NATO chamber will shoot either 5.56 mm NATO or .223 Rem. and is used by most makers of complete rifles and components.

Many AR (Armalite) type rifles use 1:9, which is suitable for bullets up to 69 grains or 4.5 grams or 1:7, which is suitable for bullets up to 85 grains or 5.5 grams. Many AR rifle owners choose to build their own rifles, which is facilitated by a huge variety of barrels and other components. The custom built AR may have a barrel from 7.5" (which may be classed as a pistol, if lacking a stock) to as long as 24" used in varmint rifles primarily, often with Wylde or Noveske chambering. US AR builders tend to follow the same trend as the US military in building rifles with Picatinny rails that support many accessories.[12]

Cartridge case

The external dimensional specifications of .223 Remington and 5.56 NATO brass cases are identical. The cases tend to have similar case capacity when measured, with variations chiefly due to brand, not 5.56 vs .223 designation. The result of this is that there is no such thing as "5.56 brass" or ".223 brass", the differences in the cartridges lie in powder loads which are affected by variations in case capacity. Brass for the 5.56 mm tends to be thicker. When handloaded, care is taken to look for pressure signs as 5.56 mm cases may produce higher pressures with the same type of powder and bullet as compared to .223 Rem cases. Case capacities have been observed to vary by as much as 2.6 grains. Sierra provides separate loading sections for .223 Rem and 5.56 mm NATO and also recommends different loads for bolt action rifles as compared to semi-automatic rifles.[13][14]

.223 Remington vs. 5.56×45mm NATO chambers

The .223 Remington and 5.56×45mm NATO barrel chamberings are dissimilar.[15] While the cartridges are identical other than powder load, bullet weight, and chamber pressure, a significant difference is in barrel of the rifle to be used, not in the cartridge. The chamber leades (throating) of the barrels of these rifles differ between designs.

The leade is the distance from the projectile while seated in the case to the rifling, which is typically shorter in .223 Remington commercial chambers. Because of this, a cartridge loaded to generate 5.56×45mm NATO pressures in a 5.56×45mm NATO chamber may develop pressures that exceed SAAMI limits for .223 Remington when fired from a short-leade .223 Remington chamber. See the section on .223 Remington#Pressure

The throating issue exists because in the US it has been traditional to have short chambers so that the bullet is being engaged at the moment of insertion. European practice has more of a forcing cone construction which can, by itself, allow significantly higher chamber pressure. All Sig-Sauer handguns (for example) have European throating and all are certified to fire +P ammunition. Short throating and unnoticed bullet setback can easily increase chamber pressures by more than 10,000 psi.

It has been observed that 5.56×45mm NATO ammunition is not as accurate as .223 Remington in many of the AR type rifles extant even with the same bullet weight. A solution to the problem has been developed by Bill Wylde and it bears his name. .223 Wylde is not a cartridge, it is a barrel chamber specification - with the external dimensions and lead angle as found in the military 5.56×45mm NATO cartridge and the 0.224 inch freebore diameter as found in the civilian SAAMI .223 Remington cartridge - that was designed to increase the accuracy of 5.56×45mm NATO ammunition to that of .223 Remington.[16] The Noveske company also has a chamber design which increases 5.56mm NATO accuracy.[17]

Pressure

Remington submitted the specifications for the .223 Remington cartridge in 1964 to SAAMI. The original pressure for the .223 Rem was 52,000 psi with DuPont IMR Powder. The current pressure of 55,000 psi (379 MPa) resulted from the change from IMR to Olin Ball powder.[5] The official name for .223 Remington in the US Army is cartridge 5.56 x 45mm ball, M193. If a 5.56×45mm NATO cartridge is loaded into a chamber intended to use .223 Remington the bullet will be in contact with the rifling and the forcing cone is very tight. This generates a much higher pressure than .223 chambers are designed for.[18] NATO chose a 178 mm (1-in-7") rifling twist rate for the 5.56×45mm NATO chambering. The SS109/M855 5.56×45mm NATO ball cartridge requires a 228 mm (1-in-9") twist rate, while adequately stabilizing the longer NATO L110/M856 5.56×45mm NATO tracer projectile requires an even faster 178 mm (1-in-7") twist rate.[5]

The table contains some estimated pressures based on normal proofing practice and on the known increases in pressure caused by bullet setback (which is a similar occurrence with regard to pressure). The proof pressure of M197 is 70,000 psi.[19]

The following table shows the differences in nomenclature, rifling, throating, normal, maximum and safe pressures:[5][4]

CartridgeUS designationNATO designationBulletRiflingThroatPressure in NATO chamberin .223 SAAMI chamberSafe sustained
.223 Remington.223 Rem55gr FMJBT1:14tight52,000 psi (359 MPa)52,000 psi (359 MPa)Yes
.223 RemingtonM1935.56×45mm55gr FMJBT1:12tight55,000 psi (379 MPa)55,000 psi (379 MPa)Yes
.223 RemingtonM197C10524197-56-21:12tight70,000 psi (483 MPa)70,000 psi (483 MPa)One time only
5.56×45 mm NATOM855SS10962 gr ball1:7long62,366 psi (430 MPa) EPVATover 70,000 psi (483 MPa)No
5.56×45 mm NATOM856L11077gr Tracer1:7long62,366 psi (430 MPa) EPVATover 70,000 psi (483 MPa)No
5.56×45 mm NATOM857SS111Tungsten carbide1:7long62,366 psi (430 MPa) EPVATover 70,000 psi (483 MPa)No
5.56×45 mm NATOProofProofunknown1:7long77,958 psi (538 MPa) EPVAT82,250 psi (567 MPa) estimatedNo

Beside the NATO EPVAT testing pressure testing protocols the other employed peak pressure measurement methodology or methodologies to correlate this table remain unknown.

Effects of barrel length on velocity

Barrel length helps determine a specific cartridge's muzzle velocity. A longer barrel will typically yield a greater muzzle velocity, while a short barrel will yield a lower one. The first AR-15 rifles used a barrel length of 20". In the case of the .223 Rem (M193) ammunition loses or gains approximately 25.7 feet-per-second for each inch of barrel length, while 5.56×45 mm NATO (M855) loses or gains 30.3 feet-per-second per inch of barrel length.[20]

P.O. Ackley created an improved version of this cartridge, called the .223 Ackley Improved.[21] It has the straight sides and steep shoulder, typical of the Ackley design improvements, yielding about 5 % extra case volume. This, in turn, provides longer case life, less stretching, and up to 140 ft/s (43 m/s) faster velocities.[22]

Wildcat cartridge developers have for a long time necked this cartridge up to create the 6 mm/223 or 6×45mm. At one time this round was very popular for varmint hunting and competition, but has been replaced by current popular competition cartridges using short, fat cases, such as the 6 mm PPC and the 6mm Norma BR.

The Thompson/Center Ugalde family of wildcat cartridges are also made by necking up .223 Remington cases, for use in the Thompson/Center Contender target pistol.

See also

References

  1. ↑ "223 REM". federalpremium.com. Retrieved 9 March 2017.
  2. ↑ ".223 Remington". black-hills.com. Retrieved 9 March 2017.
  3. ↑ "Product - Sierra Bullets - The Bulletsmiths". www.sierrabullets.com.
  4. 1 2 3 4 5 Barnes, Frank C. (2016). Cartridges of the World. Iola, WI, USA: Krause Publishing. p. 88. ISBN 978-1-4402-4265-6.
  5. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Watters, Daniel. "A 5.56 X 45mm "Timeline"". wayback.org. Archived from the original on 9 February 2004. Retrieved 6 March 2017.
  6. ↑ "223 Rem + 223 AI Cartridge Guide". 6mmbr.com.
  7. 1 2 "C.I.P. TDCC .223 Rem" (PDF).
  8. ↑ "SAAMI Pressures". Archived from the original on 14 October 2007. Retrieved 2007-11-29.
  9. ↑ ANSI/SAAMI Velocity & Pressure Data: Centerfire Rifle Archived 2013-07-15 at WebCite
  10. ↑ "Ruger Catalog". www.ruger.com.
  11. ↑ "Archived copy". Archived from the original on 2016-07-18. Retrieved 2016-07-10.
  12. ↑ ".223 Remington Vs. 5.56: What's in a Name?". americanrifleman.org. Retrieved 8 March 2017.
  13. ↑ 6mmbr.com. "223 Rem + 223 AI Cartridge Guide".
  14. ↑ "5.56 vs .223 – What You Know May Be Wrong". Retrieved 13 June 2013.
  15. ↑ .223 Remington and 5.56×45mm NATO Chamber dimensions differences Archived March 15, 2014, at the Wayback Machine.
  16. ↑ "Clearing the Caliber Confusion: .223 Wylde vs. 5.56 NATO - American Weapons Components". 16 September 2016.
  17. ↑ "Noveske Rifleworks 13.7" 5.56 Infidel Gen III Complete Upper". primaryarms.com. Retrieved 8 March 2017.
  18. ↑ "223 Rem + 223 AI Cartridge Guide". 6mmbr.com. Retrieved 8 March 2017.
  19. ↑ Barnes, Frank C. (2014). Cartridges of the World. Iola, WI, USA: Krause Publishing. p. 688. ISBN 978-1-4402-4265-6.
  20. ↑ "223 Remington/5.56 NATO, velocity versus barrel length: A man, his chop box and his friend's rifle". 20 April 2014.
  21. ↑ "Chambering a rifle for an Ackley Improved Cartridge". rifleshooter.com. Retrieved 9 March 2017.
  22. ↑ "223 Rem + 223 AI Cartridge Guide". www.6mmbr.com.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.