OBD-II PIDs

OBD-II PIDs (On-board diagnostics Parameter IDs) are codes used to request data from a vehicle, used as a diagnostic tool.

SAE standard J1979 defines many OBD-II PIDs. All on-road vehicles and trucks sold in North America are required to support a subset of these codes, primarily for state mandated emissions inspections. Manufacturers also define additional PIDs specific to their vehicles. Though not mandated, many motorcycles also support OBD-II PIDs.

In 1996, light duty vehicles (less than 8,500 lb [3,900 kg]) were the first to be mandated followed by medium duty vehicles (between 8,500–14,000 lb [3,900–6,400 kg]) in 2005.[1] They are both required to be accessed through a standardized data link connector defined by SAE J1962.

Heavy duty vehicles (greater than 14,000 lb [6,400 kg]) made after 2010,[1] for sale in the US are allowed to support OBD-II diagnostics through SAE standard J1939-13 (a round diagnostic connector) according to CARB in title 13 CCR 1971.1. Some heavy duty trucks in North America use the SAE J1962 OBD-II diagnostic connector that is common with passenger cars, notably Mack and Volvo Trucks, however they use 29 bit CAN identifiers (unlike 11 bit headers used by passenger cars).

Services

There are 10 diagnostic services described in the latest OBD-II standard SAE J1979. Before 2002, J1979 referred to these services as "modes". They are as follows:

Service (hex)	Description
01	Show current data
02	Show freeze frame data
03	Show stored Diagnostic Trouble Codes
04	Clear Diagnostic Trouble Codes and stored values
05	Test results, oxygen sensor monitoring (non CAN only)
06	Test results, other component/system monitoring (Test results, oxygen sensor monitoring for CAN only)
07	Show pending Diagnostic Trouble Codes (detected during current or last driving cycle)
08	Control operation of on-board component/system
09	Request vehicle information
0A	Permanent Diagnostic Trouble Codes (DTCs) (Cleared DTCs)

Vehicle manufacturers are not required to support all services. Each manufacturer may define additional services above #9 (e.g.: service 22 as defined by SAE J2190 for Ford/GM, service 21 for Toyota) for other information e.g. the voltage of the traction battery in a hybrid electric vehicle (HEV).[2]

The nonOBD UDS services start at 0x10 to avoid overlap of ID-range.

Standard PIDs

The table below shows the standard OBD-II PIDs as defined by SAE J1979. The expected response for each PID is given, along with information on how to translate the response into meaningful data. Again, not all vehicles will support all PIDs and there can be manufacturer-defined custom PIDs that are not defined in the OBD-II standard.

Note that services 01 and 02 are basically identical, except that service 01 provides current information, whereas service 02 provides a snapshot of the same data taken at the point when the last diagnostic trouble code was set. The exceptions are PID 01, which is only available in service 01, and PID 02, which is only available in service 02. If service 02 PID 02 returns zero, then there is no snapshot and all other service 02 data is meaningless.

When using Bit-Encoded-Notation, quantities like C4 means bit 4 from data byte C. Each bit is numerated from 0 to 7, so 7 is the most significant bit and 0 is the least significant bit (See below).

A								B								C								D
A7	A6	A5	A4	A3	A2	A1	A0	B7	B6	B5	B4	B3	B2	B1	B0	C7	C6	C5	C4	C3	C2	C1	C0	D7	D6	D5	D4	D3	D2	D1	D0

Service 01

PID (hex)	PID (Dec)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]
00	0	4	PIDs supported [01 - 20]				Bit encoded [A7..D0] == [PID $01..PID $20] See below
01	1	4	Monitor status since DTCs cleared. (Includes malfunction indicator lamp (MIL) status and number of DTCs.)				Bit encoded. See below
02	2	2	Freeze DTC
03	3	2	Fuel system status				Bit encoded. See below
04	4	1	Calculated engine load	0	100	%	${\tfrac {100}{255}}A$ (or ${\tfrac {A}{2.55}}$ )
05	5	1	Engine coolant temperature	-40	215	°C	$A-40$
06	6	1	Short term fuel trim—Bank 1	-100 (Reduce Fuel: Too Rich)	99.2 (Add Fuel: Too Lean)	%	${\frac {100}{128}}A-100$ (or ${\tfrac {A}{1.28}}-100$ )
07	7	1	Long term fuel trim—Bank 1
08	8	1	Short term fuel trim—Bank 2
09	9	1	Long term fuel trim—Bank 2
0A	10	1	Fuel pressure (gauge pressure)	0	765	kPa	$3A$
0B	11	1	Intake manifold absolute pressure	0	255	kPa	$A$
0C	12	2	Engine RPM	0	16,383.75	rpm	${\frac {256A+B}{4}}$
0D	13	1	Vehicle speed	0	255	km/h	$A$
0E	14	1	Timing advance	-64	63.5	° before TDC	${\frac {A}{2}}-64$
0F	15	1	Intake air temperature	-40	215	°C	$A-40$
10	16	2	MAF air flow rate	0	655.35	grams/sec	${\frac {256A+B}{100}}$
11	17	1	Throttle position	0	100	%	${\tfrac {100}{255}}A$
12	18	1	Commanded secondary air status				Bit encoded. See below
13	19	1	Oxygen sensors present (in 2 banks)				[A0..A3] == Bank 1, Sensors 1-4. [A4..A7] == Bank 2...
14	20	2	Oxygen Sensor 1 A: Voltage B: Short term fuel trim	0 -100	1.275 99.2	volts %	${\frac {A}{200}}$ ${\frac {100}{128}}B-100$ (if B==$FF, sensor is not used in trim calculation)
15	21	2	Oxygen Sensor 2 A: Voltage B: Short term fuel trim
16	22	2	Oxygen Sensor 3 A: Voltage B: Short term fuel trim
17	23	2	Oxygen Sensor 4 A: Voltage B: Short term fuel trim
18	24	2	Oxygen Sensor 5 A: Voltage B: Short term fuel trim
19	25	2	Oxygen Sensor 6 A: Voltage B: Short term fuel trim
1A	26	2	Oxygen Sensor 7 A: Voltage B: Short term fuel trim
1B	27	2	Oxygen Sensor 8 A: Voltage B: Short term fuel trim
1C	28	1	OBD standards this vehicle conforms to	1	250	-	enumerated. See below
1D	29	1	Oxygen sensors present (in 4 banks)				Similar to PID 13, but [A0..A7] == [B1S1, B1S2, B2S1, B2S2, B3S1, B3S2, B4S1, B4S2]
1E	30	1	Auxiliary input status				A0 == Power Take Off (PTO) status (1 == active) [A1..A7] not used
1F	31	2	Run time since engine start	0	65,535	seconds	$256A+B$
20	32	4	PIDs supported [21 - 40]				Bit encoded [A7..D0] == [PID $21..PID $40] See below
21	33	2	Distance traveled with malfunction indicator lamp (MIL) on	0	65,535	km	$256A+B$
22	34	2	Fuel Rail Pressure (relative to manifold vacuum)	0	5177.265	kPa	$0.079(256A+B)$
23	35	2	Fuel Rail Gauge Pressure (diesel, or gasoline direct injection)	0	655,350	kPa	$10(256A+B)$
24	36	4	Oxygen Sensor 1 AB: Fuel–Air Equivalence Ratio CD: Voltage	0 0	< 2 < 8	ratio V	${\frac {2}{65536}}(256A+B)$ ${\frac {8}{65536}}(256C+D)$
25	37	4	Oxygen Sensor 2 AB: Fuel–Air Equivalence Ratio CD: Voltage
26	38	4	Oxygen Sensor 3 AB: Fuel–Air Equivalence Ratio CD: Voltage
27	39	4	Oxygen Sensor 4 AB: Fuel–Air Equivalence Ratio CD: Voltage
28	40	4	Oxygen Sensor 5 AB: Fuel–Air Equivalence Ratio CD: Voltage
29	41	4	Oxygen Sensor 6 AB: Fuel–Air Equivalence Ratio CD: Voltage
2A	42	4	Oxygen Sensor 7 AB: Fuel–Air Equivalence Ratio CD: Voltage
2B	43	4	Oxygen Sensor 8 AB: Fuel–Air Equivalence Ratio CD: Voltage
2C	44	1	Commanded EGR	0	100	%	${\tfrac {100}{255}}A$
2D	45	1	EGR Error	-100	99.2	%	${\tfrac {100}{128}}A-100$
2E	46	1	Commanded evaporative purge	0	100	%	${\tfrac {100}{255}}A$
2F	47	1	Fuel Tank Level Input	0	100	%	${\tfrac {100}{255}}A$
30	48	1	Warm-ups since codes cleared	0	255	count	$A$
31	49	2	Distance traveled since codes cleared	0	65,535	km	$256A+B$
32	50	2	Evap. System Vapor Pressure	-8,192	8191.75	Pa	${\frac {256A+B}{4}}$ (AB is two's complement signed)[3]
33	51	1	Absolute Barometric Pressure	0	255	kPa	$A$
34	52	4	Oxygen Sensor 1 AB: Fuel–Air Equivalence Ratio CD: Current	0 -128	< 2 <128	ratio mA	${\frac {2}{65536}}(256A+B)$ ${\frac {256C+D}{256}}-128$ or $C+{\frac {D}{256}}-128$
35	53	4	Oxygen Sensor 2 AB: Fuel–Air Equivalence Ratio CD: Current
36	54	4	Oxygen Sensor 3 AB: Fuel–Air Equivalence Ratio CD: Current
37	55	4	Oxygen Sensor 4 AB: Fuel–Air Equivalence Ratio CD: Current
38	56	4	Oxygen Sensor 5 AB: Fuel–Air Equivalence Ratio CD: Current
39	57	4	Oxygen Sensor 6 AB: Fuel–Air Equivalence Ratio CD: Current
3A	58	4	Oxygen Sensor 7 AB: Fuel–Air Equivalence Ratio CD: Current
3B	59	4	Oxygen Sensor 8 AB: Fuel–Air Equivalence Ratio CD: Current
3C	60	2	Catalyst Temperature: Bank 1, Sensor 1	-40	6,513.5	°C	${\frac {256A+B}{10}}-40$
3D	61	2	Catalyst Temperature: Bank 2, Sensor 1
3E	62	2	Catalyst Temperature: Bank 1, Sensor 2
3F	63	2	Catalyst Temperature: Bank 2, Sensor 2
40	64	4	PIDs supported [41 - 60]				Bit encoded [A7..D0] == [PID $41..PID $60] See below
41	65	4	Monitor status this drive cycle				Bit encoded. See below
42	66	2	Control module voltage	0	65.535	V	${\frac {256A+B}{1000}}$
43	67	2	Absolute load value	0	25,700	%	${\tfrac {100}{255}}(256A+B)$
44	68	2	Fuel–Air commanded equivalence ratio	0	< 2	ratio	${\tfrac {2}{65536}}(256A+B)$
45	69	1	Relative throttle position	0	100	%	${\tfrac {100}{255}}A$
46	70	1	Ambient air temperature	-40	215	°C	$A-40$
47	71	1	Absolute throttle position B	0	100	%	${\frac {100}{255}}A$
48	72	1	Absolute throttle position C
49	73	1	Accelerator pedal position D
4A	74	1	Accelerator pedal position E
4B	75	1	Accelerator pedal position F
4C	76	1	Commanded throttle actuator
4D	77	2	Time run with MIL on	0	65,535	minutes	$256A+B$
4E	78	2	Time since trouble codes cleared	0	65,535	minutes	$256A+B$
4F	79	4	Maximum value for Fuel–Air equivalence ratio, oxygen sensor voltage, oxygen sensor current, and intake manifold absolute pressure	0, 0, 0, 0	255, 255, 255, 2550	ratio, V, mA, kPa	A, B, C, D*10
50	80	4	Maximum value for air flow rate from mass air flow sensor	0	2550	g/s	A*10, B, C, and D are reserved for future use
51	81	1	Fuel Type				From fuel type table see below
52	82	1	Ethanol fuel %	0	100	%	${\tfrac {100}{255}}A$
53	83	2	Absolute Evap system Vapor Pressure	0	327.675	kPa	${\frac {256A+B}{200}}$
54	84	2	Evap system vapor pressure	-32,767	32,768	Pa	((A*256)+B)-32767
55	85	2	Short term secondary oxygen sensor trim, A: bank 1, B: bank 3	-100	99.2	%	${\frac {100}{128}}A-100$ ${\frac {100}{128}}B-100$
56	86	2	Long term secondary oxygen sensor trim, A: bank 1, B: bank 3
57	87	2	Short term secondary oxygen sensor trim, A: bank 2, B: bank 4
58	88	2	Long term secondary oxygen sensor trim, A: bank 2, B: bank 4
59	89	2	Fuel rail absolute pressure	0	655,350	kPa	$10(256A+B)$
5A	90	1	Relative accelerator pedal position	0	100	%	${\tfrac {100}{255}}A$
5B	91	1	Hybrid battery pack remaining life	0	100	%	${\tfrac {100}{255}}A$
5C	92	1	Engine oil temperature	-40	210	°C	$A-40$
5D	93	2	Fuel injection timing	-210.00	301.992	°	${\frac {256A+B}{128}}-210$
5E	94	2	Engine fuel rate	0	3212.75	L/h	${\frac {256A+B}{20}}$
5F	95	1	Emission requirements to which vehicle is designed				Bit Encoded
60	96	4	PIDs supported [61 - 80]				Bit encoded [A7..D0] == [PID $61..PID $80] See below
61	97	1	Driver's demand engine - percent torque	-125	130	%	A-125
62	98	1	Actual engine - percent torque	-125	130	%	A-125
63	99	2	Engine reference torque	0	65,535	Nm	$256A+B$
64	100	5	Engine percent torque data	-125	130	%	A-125 Idle B-125 Engine point 1 C-125 Engine point 2 D-125 Engine point 3 E-125 Engine point 4
65	101	2	Auxiliary input / output supported				Bit Encoded
66	102	5	Mass air flow sensor
67	103	3	Engine coolant temperature			°C
68	104	7	Intake air temperature sensor
69	105	7	Commanded EGR and EGR Error
6A	106	5	Commanded Diesel intake air flow control and relative intake air flow position
6B	107	5	Exhaust gas recirculation temperature
6C	108	5	Commanded throttle actuator control and relative throttle position
6D	109	6	Fuel pressure control system
6E	110	5	Injection pressure control system
6F	111	3	Turbocharger compressor inlet pressure
70	112	9	Boost pressure control
71	113	5	Variable Geometry turbo (VGT) control
72	114	5	Wastegate control
73	115	5	Exhaust pressure
74	116	5	Turbocharger RPM
75	117	7	Turbocharger temperature
76	118	7	Turbocharger temperature
77	119	5	Charge air cooler temperature (CACT)
78	120	9	Exhaust Gas temperature (EGT) Bank 1				Special PID. See below
79	121	9	Exhaust Gas temperature (EGT) Bank 2				Special PID. See below
7A	122	7	Diesel particulate filter (DPF)
7B	123	7	Diesel particulate filter (DPF)
7C	124	9	Diesel Particulate filter (DPF) temperature			°C	${\frac {256A+B}{10}}-40$
7D	125	1	NOx NTE (Not-To-Exceed) control area status
7E	126	1	PM NTE (Not-To-Exceed) control area status
7F	127	13	Engine run time			seconds
80	128	4	PIDs supported [81 - A0]				Bit encoded [A7..D0] == [PID $81..PID $A0] See below
81	129	21	Engine run time for Auxiliary Emissions Control Device(AECD)
82	130	21	Engine run time for Auxiliary Emissions Control Device(AECD)
83	131	5	NOx sensor
84	132	1	Manifold surface temperature
85	133	10	NOx reagent system
86	134	5	Particulate matter (PM) sensor
87	135	5	Intake manifold absolute pressure
88	136	13	SCR Induce System
89	137	41	Run Time for AECD #11-#15
8A	138	41	Run Time for AECD #16-#20
8B	139	7	Diesel Aftertreatment
8C	140	16	O2 Sensor (Wide Range)
8D	141	1	Throttle Position G	0	100	%
8E	142	1	Engine Friction - Percent Torque	-125	130	%	$A-125$
8F	143	5	PM Sensor Bank 1 & 2
90	144	3	WWH-OBD Vehicle OBD System Information			hours
91	145	5	WWH-OBD Vehicle OBD System Information			hours
92	146	2	Fuel System Control
93	147	3	WWH-OBD Vehicle OBD Counters support			hours
94	148	12	NOx Warning And Inducement System
98	152	9	Exhaust Gas Temperature Sensor
99	153	9	Exhaust Gas Temperature Sensor
9A	154	6	Hybrid/EV Vehicle System Data, Battery, Voltage
9B	155	4	Diesel Exhaust Fluid Sensor Data
9C	156	17	O2 Sensor Data
9D	157	4	Engine Fuel Rate			g/s
9E	158	2	Engine Exhaust Flow Rate			kg/h
9F	159	9	Fuel System Percentage Use
A0	160	4	PIDs supported [A1 - C0]				Bit encoded [A7..D0] == [PID $A1..PID $C0] See below
A1	161	9	NOx Sensor Corrected Data			ppm
A2	162	2	Cylinder Fuel Rate			mg/stroke
A3	163	9	Evap System Vapor Pressure			Pa
A4	164	4	Transmission Actual Gear
A5	165	4	Diesel Exhaust Fluid Dosing
A6	166	4	Odometer	0	526 385 151.9	km	${\frac {A(2^{24})+B(2^{16})+C(2^{8})+D}{10}}$
C0	192	4	PIDs supported [C1 - E0]	0x0	0xffffffff		Bit encoded [A7..D0] == [PID $C1..PID $E0] See below
C3	195	?	?	?	?	?	Returns numerous data, including Drive Condition ID and Engine Speed*
C4	196	?	?	?	?	?	B5 is Engine Idle Request B6 is Engine Stop Request*
PID (hex)	PID (Dec)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]

Service 02

Service 02 accepts the same PIDs as service 01, with the same meaning, but information given is from when the freeze frame[4] was created.

You have to send the frame number in the data section of the message.

PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]
02	2	DTC that caused freeze frame to be stored.				BCD encoded. Decoded as in service 3

Service 03

PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]
N/A	n*6	Request trouble codes				3 codes per message frame. See below

Service 04

PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]
N/A	0	Clear trouble codes / Malfunction indicator lamp (MIL) / Check engine light				Clears all stored trouble codes and turns the MIL off.

Service 05

PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]
0100	4	OBD Monitor IDs supported ($01 – $20)	0x0	0xffffffff
0101	2	O2 Sensor Monitor Bank 1 Sensor 1	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0102		O2 Sensor Monitor Bank 1 Sensor 2	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0103		O2 Sensor Monitor Bank 1 Sensor 3	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0104		O2 Sensor Monitor Bank 1 Sensor 4	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0105		O2 Sensor Monitor Bank 2 Sensor 1	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0106		O2 Sensor Monitor Bank 2 Sensor 2	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0107		O2 Sensor Monitor Bank 2 Sensor 3	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0108		O2 Sensor Monitor Bank 2 Sensor 4	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0109		O2 Sensor Monitor Bank 3 Sensor 1	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
010A		O2 Sensor Monitor Bank 3 Sensor 2	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
010B		O2 Sensor Monitor Bank 3 Sensor 3	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
010C		O2 Sensor Monitor Bank 3 Sensor 4	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
010D		O2 Sensor Monitor Bank 4 Sensor 1	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
010E		O2 Sensor Monitor Bank 4 Sensor 2	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
010F		O2 Sensor Monitor Bank 4 Sensor 3	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0110		O2 Sensor Monitor Bank 4 Sensor 4	0.00	1.275	volts	0.005 Rich to lean sensor threshold voltage
0201		O2 Sensor Monitor Bank 1 Sensor 1	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0202		O2 Sensor Monitor Bank 1 Sensor 2	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0203		O2 Sensor Monitor Bank 1 Sensor 3	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0204		O2 Sensor Monitor Bank 1 Sensor 4	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0205		O2 Sensor Monitor Bank 2 Sensor 1	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0206		O2 Sensor Monitor Bank 2 Sensor 2	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0207		O2 Sensor Monitor Bank 2 Sensor 3	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0208		O2 Sensor Monitor Bank 2 Sensor 4	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0209		O2 Sensor Monitor Bank 3 Sensor 1	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
020A		O2 Sensor Monitor Bank 3 Sensor 2	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
020B		O2 Sensor Monitor Bank 3 Sensor 3	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
020C		O2 Sensor Monitor Bank 3 Sensor 4	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
020D		O2 Sensor Monitor Bank 4 Sensor 1	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
020E		O2 Sensor Monitor Bank 4 Sensor 2	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
020F		O2 Sensor Monitor Bank 4 Sensor 3	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
0210		O2 Sensor Monitor Bank 4 Sensor 4	0.00	1.275	volts	0.005 Lean to Rich sensor threshold voltage
PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]

Service 09

PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]
00	4	Service 9 supported PIDs (01 to 20)				Bit encoded. [A7..D0] = [PID $01..PID $20] See below
01	1	VIN Message Count in PID 02. Only for ISO 9141-2, ISO 14230-4 and SAE J1850.				Usually the value will be 5.
02	17	Vehicle Identification Number (VIN)				17-char VIN, ASCII-encoded and left-padded with null chars (0x00) if needed to.
03	1	Calibration ID message count for PID 04. Only for ISO 9141-2, ISO 14230-4 and SAE J1850.				It will be a multiple of 4 (4 messages are needed for each ID).
04	16,32,48,64..	Calibration ID				Up to 16 ASCII chars. Data bytes not used will be reported as null bytes (0x00). Several CALID can be outputed (16 bytes each)
05	1	Calibration verification numbers (CVN) message count for PID 06. Only for ISO 9141-2, ISO 14230-4 and SAE J1850.
06	4,8,12,16	Calibration Verification Numbers (CVN) Several CVN can be output (4 bytes each) the number of CVN and CALID must match				Raw data left-padded with null characters (0x00). Usually displayed as hex string.
07	1	In-use performance tracking message count for PID 08 and 0B. Only for ISO 9141-2, ISO 14230-4 and SAE J1850.	8	10		8 if sixteen (16) values are required to be reported, 9 if eighteen (18) values are required to be reported, and 10 if twenty (20) values are required to be reported (one message reports two values, each one consisting in two bytes).
08	4	In-use performance tracking for spark ignition vehicles				4 or 5 messages, each one containing 4 bytes (two values). See below
09	1	ECU name message count for PID 0A
0A	20	ECU name				ASCII-coded. Right-padded with null chars (0x00).
0B	4	In-use performance tracking for compression ignition vehicles				5 messages, each one containing 4 bytes (two values). See below
PID (hex)	Data bytes returned	Description	Min value	Max value	Units	Formula[lower-alpha 1]

In the formula column, letters A, B, C, etc. represent the decimal equivalent of the first, second, third, etc. bytes of data. Where a (?) appears, contradictory or incomplete information was available.

Bitwise encoded PIDs

Some of the PIDs in the above table cannot be explained with a simple formula. A more elaborate explanation of these data is provided here:

Service 01 PID 00

A request for this PID returns 4 bytes of data (Big-endian). Each bit, from MSB to LSB, represents one of the next 32 PIDs and specifies whether that PID is supported.

For example, if the car response is BE1FA813, it can be decoded like this:

Hexadecimal	B				E				1				F				A				8				1				3
Binary	1	0	1	1	1	1	1	0	0	0	0	1	1	1	1	1	1	0	1	0	1	0	0	0	0	0	0	1	0	0	1	1
Supported?	Yes	No	Yes	Yes	Yes	Yes	Yes	No	No	No	No	Yes	Yes	Yes	Yes	Yes	Yes	No	Yes	No	Yes	No	No	No	No	No	No	Yes	No	No	Yes	Yes
PID number	01	02	03	04	05	06	07	08	09	0A	0B	0C	0D	0E	0F	10	11	12	13	14	15	16	17	18	19	1A	1B	1C	1D	1E	1F	20

So, supported PIDs are: 01, 03, 04, 05, 06, 07, 0C, 0D, 0E, 0F, 10, 11, 13, 15, 1C, 1F and 20

Service 01 PID 01

A request for this PID returns 4 bytes of data, labeled A B C and D.

The first byte(A) contains two pieces of information. Bit A7 (MSB of byte A, the first byte) indicates whether or not the MIL (check engine light) is illuminated. Bits A6 through A0 represent the number of diagnostic trouble codes currently flagged in the ECU.

The second, third, and fourth bytes(B, C and D) give information about the availability and completeness of certain on-board tests. Note that test availability is indicated by set (1) bit and completeness is indicated by reset (0) bit.

Bit	Name	Definition
A7	MIL	Off or On, indicates if the CEL/MIL is on (or should be on)
A6-A0	DTC_CNT	Number of confirmed emissions-related DTCs available for display.
B7	RESERVED	Reserved (should be 0)
B3	NO NAME	0 = Spark ignition monitors supported (e.g. Otto or Wankel engines) 1 = Compression ignition monitors supported (e.g. Diesel engines)

Here are the common bit B definitions, they are test based.

	Test available	Test incomplete
Components	B2	B6
Fuel System	B1	B5
Misfire	B0	B4

The third and fourth bytes are to be interpreted differently depending on if the engine is spark ignition (e.g. Otto or Wankel engines) or compression ignition (e.g. Diesel engines). In the second (B) byte, bit 3 indicates how to interpret the C and D bytes, with 0 being spark (Otto or Wankel) and 1 (set) being compression (Diesel).

The bytes C and D for spark ignition monitors (e.g. Otto or Wankel engines):

	Test available	Test incomplete
EGR System	C7	D7
Oxygen Sensor Heater	C6	D6
Oxygen Sensor	C5	D5
A/C Refrigerant	C4	D4
Secondary Air System	C3	D3
Evaporative System	C2	D2
Heated Catalyst	C1	D1
Catalyst	C0	D0

And the bytes C and D for compression ignition monitors (Diesel engines):

	Test available	Test incomplete
EGR and/or VVT System	C7	D7
PM filter monitoring	C6	D6
Exhaust Gas Sensor	C5	D5
- Reserved -	C4	D4
Boost Pressure	C3	D3
- Reserved -	C2	D2
NOx/SCR Monitor	C1	D1
NMHC Catalyst[lower-alpha 1]	C0	D0

NMHC may stand for Non-Methane HydroCarbons, but J1979 does not enlighten us. The translation would be the ammonia sensor in the SCR catalyst.

Service 01 PID 41

A request for this PID returns 4 bytes of data. The first byte is always zero. The second, third, and fourth bytes give information about the availability and completeness of certain on-board tests. As with PID 01, the third and fourth bytes are to be interpreted differently depending on the ignition type (B3) – with 0 being spark and 1 (set) being compression. Note again that test availability is represented by a set (1) bit and completeness is represented by a reset (0) bit.

Here are the common bit B definitions, they are test based.

	Test available	Test incomplete
Components	B2	B6
Fuel System	B1	B5
Misfire	B0	B4

The bytes C and D for spark ignition monitors (e.g. Otto or Wankel engines):

	Test available	Test incomplete
EGR System	C7	D7
Oxygen Sensor Heater	C6	D6
Oxygen Sensor	C5	D5
A/C Refrigerant	C4	D4
Secondary Air System	C3	D3
Evaporative System	C2	D2
Heated Catalyst	C1	D1
Catalyst	C0	D0

And the bytes C and D for compression ignition monitors (Diesel engines):

	Test available	Test incomplete
EGR and/or VVT System	C7	D7
PM filter monitoring	C6	D6
Exhaust Gas Sensor	C5	D5
- Reserved -	C4	D4
Boost Pressure	C3	D3
- Reserved -	C2	D2
NOx/SCR Monitor	C1	D1
NMHC Catalyst[lower-alpha 1]	C0	D0

NMHC may stand for Non-Methane HydroCarbons, but J1979 does not enlighten us. The translation would be the ammonia sensor in the SCR catalyst.

Service 01 PID 78

A request for this PID will return 9 bytes of data. The first byte is a bit encoded field indicating which EGT sensors are supported:

Byte	Description
A	Supported EGT sensors
B-C	Temperature read by EGT11
D-E	Temperature read by EGT12
F-G	Temperature read by EGT13
H-I	Temperature read by EGT14

The first byte is bit-encoded as follows:

Bit	Description
A7-A4	Reserved
A3	EGT bank 1, sensor 4 Supported?
A2	EGT bank 1, sensor 3 Supported?
A1	EGT bank 1, sensor 2 Supported?
A0	EGT bank 1, sensor 1 Supported?

The remaining bytes are 16 bit integers indicating the temperature in degrees Celsius in the range -40 to 6513.5 (scale 0.1), using the usual $(A\times 256+B)/10-40$ formula (MSB is A, LSB is B). Only values for which the corresponding sensor is supported are meaningful.

The same structure applies to PID 79, but values are for sensors of bank 2.

Service 03 (no PID required)

A request for this service returns a list of the DTCs that have been set. The list is encapsulated using the ISO 15765-2 protocol.

If there are two or fewer DTCs (4 bytes) they are returned in an ISO-TP Single Frame (SF). Three or more DTCs in the list are reported in multiple frames, with the exact count of frames dependent on the communication type and addressing details.

Each trouble code requires 2 bytes to describe. The text description of a trouble code may be decoded as follows. The first character in the trouble code is determined by the first two bits in the first byte:

A7-A6	First DTC character
00	P - Powertrain
01	C - Chassis
10	B - Body
11	U - Network

The two following digits are encoded as 2 bits. The second character in the DTC is a number defined by the following table:

A5-A4	Second DTC character
00	0
01	1
10	2
11	3

The third character in the DTC is a number defined by

A3-A0	Third DTC character
0000	0
0001	1
0010	2
0011	3
0100	4
0101	5
0110	6
0111	7
1000	8
1001	9
1010	A
1011	B
1100	C
1101	D
1110	E
1111	F

The fourth and fifth characters are defined in the same way as the third, but using bits B7-B4 and B3-B0. The resulting five-character code should look something like "U0158" and can be looked up in a table of OBD-II DTCs. Hexadecimal characters (0-9, A-F), while relatively rare, are allowed in the last 3 positions of the code itself.

Service 09 PID 08

It provides information about track in-use performance for catalyst banks, oxygen sensor banks, evaporative leak detection systems, EGR systems and secondary air system.

The numerator for each component or system tracks the number of times that all conditions necessary for a specific monitor to detect a malfunction have been encountered. The denominator for each component or system tracks the number of times that the vehicle has been operated in the specified conditions.

The count of data items should be reported at the beginning (the first byte).

All data items of the In-use Performance Tracking record consist of two (2) bytes and are reported in this order (each message contains two items, hence the message length is 4).

Mnemonic	Description
OBDCOND	OBD Monitoring Conditions Encountered Counts
IGNCNTR	Ignition Counter
CATCOMP1	Catalyst Monitor Completion Counts Bank 1
CATCOND1	Catalyst Monitor Conditions Encountered Counts Bank 1
CATCOMP2	Catalyst Monitor Completion Counts Bank 2
CATCOND2	Catalyst Monitor Conditions Encountered Counts Bank 2
O2SCOMP1	O2 Sensor Monitor Completion Counts Bank 1
O2SCOND1	O2 Sensor Monitor Conditions Encountered Counts Bank 1
O2SCOMP2	O2 Sensor Monitor Completion Counts Bank 2
O2SCOND2	O2 Sensor Monitor Conditions Encountered Counts Bank 2
EGRCOMP	EGR Monitor Completion Condition Counts
EGRCOND	EGR Monitor Conditions Encountered Counts
AIRCOMP	AIR Monitor Completion Condition Counts (Secondary Air)
AIRCOND	AIR Monitor Conditions Encountered Counts (Secondary Air)
EVAPCOMP	EVAP Monitor Completion Condition Counts
EVAPCOND	EVAP Monitor Conditions Encountered Counts
SO2SCOMP1	Secondary O2 Sensor Monitor Completion Counts Bank 1
SO2SCOND1	Secondary O2 Sensor Monitor Conditions Encountered Counts Bank 1
SO2SCOMP2	Secondary O2 Sensor Monitor Completion Counts Bank 2
SO2SCOND2	Secondary O2 Sensor Monitor Conditions Encountered Counts Bank 2

Service 09 PID 0B

It provides information about track in-use performance for NMHC catalyst, NOx catalyst monitor, NOx adsorber monitor, PM filter monitor, exhaust gas sensor monitor, EGR/ VVT monitor, boost pressure monitor and fuel system monitor.

All data items consist of two (2) bytes and are reported in this order (each message contains two items, hence message length is 4):

Mnemonic	Description
OBDCOND	OBD Monitoring Conditions Encountered Counts
IGNCNTR	Ignition Counter
HCCATCOMP	NMHC Catalyst Monitor Completion Condition Counts
HCCATCOND	NMHC Catalyst Monitor Conditions Encountered Counts
NCATCOMP	NOx/SCR Catalyst Monitor Completion Condition Counts
NCATCOND	NOx/SCR Catalyst Monitor Conditions Encountered Counts
NADSCOMP	NOx Adsorber Monitor Completion Condition Counts
NADSCOND	NOx Adsorber Monitor Conditions Encountered Counts
PMCOMP	PM Filter Monitor Completion Condition Counts
PMCOND	PM Filter Monitor Conditions Encountered Counts
EGSCOMP	Exhaust Gas Sensor Monitor Completion Condition Counts
EGSCOND	Exhaust Gas Sensor Monitor Conditions Encountered Counts
EGRCOMP	EGR and/or VVT Monitor Completion Condition Counts
EGRCOND	EGR and/or VVT Monitor Conditions Encountered Counts
BPCOMP	Boost Pressure Monitor Completion Condition Counts
BPCOND	Boost Pressure Monitor Conditions Encountered Counts
FUELCOMP	Fuel Monitor Completion Condition Counts
FUELCOND	Fuel Monitor Conditions Encountered Counts

Enumerated PIDs

Some PIDs are to be interpreted specially, and aren't necessarily exactly bitwise encoded, or in any scale. The values for these PIDs are enumerated.

Service 01 PID 03

A request for this PID returns 2 bytes of data. The first byte describes fuel system #1.

Value	Description
1	Open loop due to insufficient engine temperature
2	Closed loop, using oxygen sensor feedback to determine fuel mix
4	Open loop due to engine load OR fuel cut due to deceleration
8	Open loop due to system failure
16	Closed loop, using at least one oxygen sensor but there is a fault in the feedback system

Any other value is an invalid response.

The second byte describes fuel system #2 (if it exists) and is encoded identically to the first byte.

Service 01 PID 12

A request for this PID returns a single byte of data which describes the secondary air status.

Value	Description
1	Upstream
2	Downstream of catalytic converter
4	From the outside atmosphere or off
8	Pump commanded on for diagnostics

Any other value is an invalid response.

Service 01 PID 1C

A request for this PID returns a single byte of data which describes which OBD standards this ECU was designed to comply with. The different values the data byte can hold are shown below, next to what they mean:

Value	Description
1	OBD-II as defined by the CARB
2	OBD as defined by the EPA
3	OBD and OBD-II
4	OBD-I
5	Not OBD compliant
6	EOBD (Europe)
7	EOBD and OBD-II
8	EOBD and OBD
9	EOBD, OBD and OBD II
10	JOBD (Japan)
11	JOBD and OBD II
12	JOBD and EOBD
13	JOBD, EOBD, and OBD II
14	Reserved
15	Reserved
16	Reserved
17	Engine Manufacturer Diagnostics (EMD)
18	Engine Manufacturer Diagnostics Enhanced (EMD+)
19	Heavy Duty On-Board Diagnostics (Child/Partial) (HD OBD-C)
20	Heavy Duty On-Board Diagnostics (HD OBD)
21	World Wide Harmonized OBD (WWH OBD)
22	Reserved
23	Heavy Duty Euro OBD Stage I without NOx control (HD EOBD-I)
24	Heavy Duty Euro OBD Stage I with NOx control (HD EOBD-I N)
25	Heavy Duty Euro OBD Stage II without NOx control (HD EOBD-II)
26	Heavy Duty Euro OBD Stage II with NOx control (HD EOBD-II N)
27	Reserved
28	Brazil OBD Phase 1 (OBDBr-1)
29	Brazil OBD Phase 2 (OBDBr-2)
30	Korean OBD (KOBD)
31	India OBD I (IOBD I)
32	India OBD II (IOBD II)
33	Heavy Duty Euro OBD Stage VI (HD EOBD-IV)
34-250	Reserved
251-255	Not available for assignment (SAE J1939 special meaning)

Fuel Type Coding

Service 01 PID 51 returns a value from an enumerated list giving the fuel type of the vehicle. The fuel type is returned as a single byte, and the value is given by the following table:

Value	Description
0	Not available
1	Gasoline
2	Methanol
3	Ethanol
4	Diesel
5	LPG
6	CNG
7	Propane
8	Electric
9	Bifuel running Gasoline
10	Bifuel running Methanol
11	Bifuel running Ethanol
12	Bifuel running LPG
13	Bifuel running CNG
14	Bifuel running Propane
15	Bifuel running Electricity
16	Bifuel running electric and combustion engine
17	Hybrid gasoline
18	Hybrid Ethanol
19	Hybrid Diesel
20	Hybrid Electric
21	Hybrid running electric and combustion engine
22	Hybrid Regenerative
23	Bifuel running diesel

Any other value is reserved by ISO/SAE. There are currently no definitions for flexible-fuel vehicle.

Non-standard PIDs

The majority of all OBD-II PIDs in use are non-standard. For most modern vehicles, there are many more functions supported on the OBD-II interface than are covered by the standard PIDs, and there is relatively minor overlap between vehicle manufacturers for these non-standard PIDs.

There is very limited information available in the public domain for non-standard PIDs. The primary source of information on non-standard PIDs across different manufacturers is maintained by the US-based Equipment and Tool Institute and only available to members. The price of ETI membership for access to scan codes varies based on company size defined by annual sales of automotive tools and equipment in North America:

Annual Sales in North America	Annual Dues
Under $10,000,000	$5,000
$10,000,000 - $50,000,000	$7,500
Greater than $50,000,000	$10,000

However, even ETI membership will not provide full documentation for non-standard PIDs. ETI state:[5][6]

Some OEMs refuse to use ETI as a one-stop source of scan tool information. They prefer to do business with each tool company separately. These companies also require that you enter into a contract with them. The charges vary but here is a snapshot as of April 13th, 2015 of the per year charges:

GM $50,000

Honda $5,000

Suzuki $1,000

BMW $25,500 plus $2,000 per update. Updates occur annually.

CAN (11-bit) bus format

The PID query and response occurs on the vehicle's CAN bus. Standard OBD requests and responses use functional addresses. The diagnostic reader initiates a query using CAN ID 7DFh, which acts as a broadcast address, and accepts responses from any ID in the range 7E8h to 7EFh. ECUs that can respond to OBD queries listen both to the functional broadcast ID of 7DFh and one assigned ID in the range 7E0h to 7E7h. Their response has an ID of their assigned ID plus 8 e.g. 7E8h through 7EFh.

This approach allows up to eight ECUs, each independently responding to OBD queries. The diagnostic reader can use the ID in the ECU response frame to continue communication with a specific ECU. In particular, multi-frame communication requires a response to the specific ECU ID rather than to ID 7DFh.

CAN bus may also be used for communication beyond the standard OBD messages. Physical addressing uses particular CAN IDs for specific modules (e.g., 720h for the instrument cluster in Fords) with proprietary frame payloads.

Query

The functional PID query is sent to the vehicle on the CAN bus at ID 7DFh, using 8 data bytes. The bytes are:

	Byte
PID Type	0	1	2	3	4	5	6	7
SAE Standard	Number of additional data bytes: 2	Service 01 = show current data; 02 = freeze frame; etc.	PID code (e.g.: 05 = Engine coolant temperature)	not used (ISO 15765-2 suggests CCh)
Vehicle specific	Number of additional data bytes: 3	Custom service: (e.g.: 22 = enhanced data)	PID code (e.g.: 4980h)		not used (ISO 15765-2 suggests CCh)

Response

The vehicle responds to the PID query on the CAN bus with message IDs that depend on which module responded. Typically the engine or main ECU responds at ID 7E8h. Other modules, like the hybrid controller or battery controller in a Prius, respond at 07E9h, 07EAh, 07EBh, etc. These are 8h higher than the physical address the module responds to. Even though the number of bytes in the returned value is variable, the message uses 8 data bytes regardless (CAN bus protocol form Frameformat with 8 data bytes). The bytes are:

	Byte
PID Type	0	1	2	3	4	5	6	7
SAE Standard 7E8h, 7E9h, 7EAh, etc.	Number of additional data bytes: 3 to 6	Custom service Same as query, except that 40h is added to the service value. So: 41h = show current data; 42h = freeze frame; etc.	PID code (e.g.: 05 = Engine coolant temperature)	value of the specified parameter, byte 0	value, byte 1 (optional)	value, byte 2 (optional)	value, byte 3 (optional)	not used (may be 00h or 55h)
Vehicle specific 7E8h, or 8h + physical ID of module.	Number of additional data bytes: 4to 7	Custom service: same as query, except that 40h is added to the service value.(e.g.: 62h = response to service 22h request)	PID code (e.g.: 4980h)		value of the specified parameter, byte 0	value, byte 1 (optional)	value, byte 2 (optional)	value, byte 3 (optional)
Vehicle specific 7E8h, or 8h + physical ID of module.	Number of additional data bytes: 3	7Fh this a general response usually indicating the module doesn't recognize the request.	Custom service: (e.g.: 22h = enhanced diagnostic data by PID, 21h = enhanced data by offset)	31h	not used (may be 00h)

References

"Basic Information | On-Board Diagnostics (OBD)". US EPA. 16 March 2015. Retrieved 24 June 2015.
"Escape PHEV TechInfo - PIDs". Electric Auto Association - Plug in Hybrid Electric Vehicle. Retrieved 11 December 2013.
"Extended PID's - Signed Variables". Torque-BHP. Retrieved 17 March 2016.
"OBD2 Freeze Frame Data: What is It? How To Read It?". OBD Advisor. 2018-02-28. Retrieved 2020-03-14.
"ETI Full Membership FAQ". The Equipment and Tool Institute. Retrieved 29 November 2013. showing cost of access to OBD-II PID documentation
"Special OEM License Requirements". The Equipment and Tool Institute. Retrieved 13 April 2015.