Industrial stormwater

Industrial stormwater is runoff from precipitation (rain, snow, sleet, freezing rain, or hail) that lands on industrial sites (e.g. manufacturing facilities, mines, airports). This runoff is often polluted by materials that are handled or stored on the sites, and the facilities are subject to regulations to control the discharges.

Regulation in the United States
Deicing of aircraft. All U.S. airports are required to obtain stormwater permits

In the United States, facilities that discharge industrial stormwater to surface waters must obtain a permit under the National Pollutant Discharge Elimination System (NPDES), pursuant to the Clean Water Act.[1] Stormwater permit regulations issued by the United States Environmental Protection Agency (EPA) govern the permit process.[2] EPA published its "Phase I" stormwater rule, which covers industrial dischargers, in 1990.[3]

Most stormwater permits in the U.S. are issued by the agencies in 47 states that have been given authority by EPA. EPA regional offices issue the stormwater permits in the remaining parts of the country.[4]

Multi-sector general permit

EPA published its Multi-Sector General Permit (MSGP) initially in 1995 to govern how industrial stormwater should be managed, and periodically it has updated and reissued the permit. The 2015 MSGP covers 29 industrial and commercial sectors:[5]

  1. Timber Products Facilities (including wood preservation)
  2. Paper and Allied Products Manufacturing Facilities
  3. Chemical and Allied Products Manufacturing and Refining
  4. Asphalt Paving and Roofing Materials and Manufacturers and Lubricant Manufacturers
  5. Glass, Clay, Cement, Concrete, and Gypsum Product Manufacturing Facilities
  6. Primary Metals Facilities
  7. Metal Mining (Ore Mining and Dressing) Facilities
  8. Coal Mines and Coal Mining-Related Facilities
  9. Oil and Gas Extraction Facilities
  10. Mineral Mining and Processing Facilities
  11. Hazardous Waste Treatment, Storage, or Disposal Facilities
    12. Scrap yards must obtain stormwater permits and control stormwater runoff
  12. Landfills and Land Application Sites
  13. Automobile Salvage Yards
  14. Scrap Recycling and Waste Recycling Facilities
  15. Steam Electric Power Generating Facilities, including Coal Handling Areas
  16. Motor Freight Transportation Facilities, Passenger Transportation Facilities, Petroleum Bulk Oil Stations and Terminals, Rail Transportation Facilities, and United States Postal Service Transportation Facilities
  17. Water Transportation Facilities with Vehicle Maintenance Shops and/or Equipment Cleaning Operations
  18. Ship and Boat Building or Repair Yards
  19. Vehicle Maintenance Areas, Equipment Cleaning Areas, or Deicing Areas Located at Air Transportation Facilities
  20. Sewage treatment plants
  21. Food and Kindred Products Facilities
  22. Textile Mills, Apparel, and Other Fabric Products Manufacturing Facilities
  23. Wood and Metal Furniture and Fixture Manufacturing Facilities
  24. Printing and Publishing Facilities
  25. Rubber, Miscellaneous Plastic Products, and Miscellaneous Manufacturing Industries
  26. Leather Tanning and Finishing Facilities
  27. Fabricated Metal Products Manufacturing Facilities
  28. Transportation Equipment, Industrial, or Commercial Machinery Manufacturing Facilities
  29. Electronic and Electrical Equipment and Components, Photographic, and Optical Goods Manufacturing Facilities

The permit is applicable to facilities in Massachusetts, New Hampshire, New Mexico, Idaho, the District of Columbia and federal insular areas (territories). The other states have developed their own state-specific industrial stormwater permits (e.g. California's Industrial General Permit).[6] State-issued general permits often include the same requirements as EPA's permit, but some states have additional requirements. Idaho will take over stormwater permit authority from EPA in 2021.[4]

A silt fence is a type of sediment control used on construction sites.

Construction site stormwater

Under EPA regulations, stormwater runoff from construction sites is also classified as industrial stormwater, however these discharges are covered by a separate set of permits. EPA periodically publishes its Construction General Permit and the approved state agencies publish similar permits, to regulate discharges from construction sites of 1 acre (4,000 m2) or more.[7] In addition to implementing the NPDES requirements, many states and local governments have enacted their own stormwater management laws and ordinances, and some have published stormwater treatment design manuals.[8][9] Some of these state and local requirements have expanded coverage beyond the federal requirements. For example, the State of Maryland requires erosion and sediment controls on construction sites of 5,000 sq ft (460 m2) or more.[10]

See also

References
  1. United States. Federal Water Pollution Control Amendments of 1972. Pub.L. 92-500, October 18, 1972; as amended by the Water Quality Act of 1987, Pub.L. 100-4, February 4, 1987. Section 402(p), 33 U.S.C. ยง 1342(p).
  2. United States Environmental Protection Sgency (EPA), Washington, D.C. "Storm water discharges." EPA Administered Permit Programs: The National Pollutant Discharge Elimination System. Code of Federal Regulations, 40 C.F.R. 122.26.
  3. EPA (1990-11-16). "National Pollutant Discharge Elimination System Permit Application Regulations for Storm Water Discharges". Federal Register, 44 FR 47990.
  4. "NPDES State Program Information". National Pollutant Discharge Elimination System (NPDES). EPA. 2019-04-27.
  5. "Stormwater Discharges from Industrial Activities". NPDES. EPA. 2019-02-14.
  6. "Industrial Storm Water Program". State Water Resources Control Board. California Environmental Protection Agency. 2016-03-22.
  7. "Stormwater Discharges from Construction Activities". NPDES. EPA. 2018-12-12.
  8. Washington State Department of Ecology (August 2012). Olympia, WA. "Stormwater Management Manual for Western Washington." Publication No. 12-10-030.
  9. Maryland Stormwater Design Manual (Report). Baltimore, MD: Maryland Department of the Environment. 2009.
  10. State of Maryland. Code of Maryland Regulations (COMAR). Activities for Which Approved Erosion and Sediment Control Plans are Required. Sec. 26.17.01.05.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.