Rifled musket

Springfield Model 1861 Rifle Musket

Pattern 1853 Enfield Rifle Musket

A rifled musket is a type of firearm made in the mid-19th century. The term referred only to muskets that had been produced as a smoothbore weapon and later had their barrels rifled. The term 'rifle musket' refers to musket length firearms that were manufactured with rifled barrels. The two terms are frequently confused.

History and development

In the early 19th century, there were rifles, and there were muskets. Muskets were smoothbore muzzle-loading weapons, firing round lead balls or buck and ball ammunition, that were also designed to accept a bayonet. Rifles were similar in that they used the same kind of flintlock or caplock firing mechanism, but the main difference was that their barrels were rifled – that is, their barrels had grooves cut into the interior surface which would cause the bullet to spin as it left the barrel.

Rifles have the advantage of long range accuracy, because spinning bullets have far flatter and more stable trajectories than balls fired from smoothbore muskets. Muskets had the advantage of a faster rate of fire. A muzzle-loaded weapon required the bullet to fit snugly into the barrel. For a smoothbore weapon this can be a somewhat loose fit, but in the case of a rifle, the helical rifling lands in the barrel have to cut into the bullet to make it spin. The fit needs to be sufficiently tight for the bullet to engage the lands in order to impart spin; otherwise the bullet will wobble as it goes down the barrel, destroying its accuracy. Furthermore, if the barrel-to-bullet seal is not tight, gases will blow through the rifling grooves and around the bullet, compromising muzzle velocity, accuracy and the bullet's terminal energy at the target. Their greater accuracy and range made rifles ideal for hunting, but the slower rate of fire was a significant impediment for widespread military use, along with the fouling caused by normal firing which made them steadily more difficult to load.

Although outwardly similar, the way muskets and rifles were used in battle was quite different. Muskets had two functions - as firearms they were used to deliver volleys of short-range fire in close ranks, and with fixed bayonets they were used much as the pikes they replaced, using formidable line and square formations. Compared to modern weapons a musket had limited range and a slow rate of fire, meaning that the bayonet played a significant role, accounting for roughly a third of all battlefield casualties during the Napoleonic and U.S. Revolutionary War eras. Bayonets were so effective on the battlefield that often the threat of bayonets was enough to cause an enemy to turn and run.^[1] Since they were used as pikes, muskets tended to be fairly long and heavy weapons. They tended to be about four to six feet in length (six to eight feet including the bayonet), with a weight of around 10 to 12 pounds (4.5 to 5.4 kg), as longer and heavier weapons were found to be too unwieldy.^[2] The length of a musket also allowed them to be fired by ranks, minimizing the risk that the men in the rear ranks would accidentally shoot the men in the front ranks in the back of the head, or, more likely, scorch their faces and burst their eardrums with the muzzle blast. Muskets six feet in length could be fired in three ranks without fear of accidents.^[3]

The relative inaccuracy and short range of the musket was not considered to be significant on the battlefield, because smoke from the black powder used at the time quickly obscured the battlefield and rendered the longer range of the rifle useless, especially as a battle progressed.^[4]

Rifles were more expensive to make than muskets, and were typically used by small units of specialized riflemen trained not to fight in closed ranks, but in open order, spread out as skirmishers or sharpshooters. Since they were not fired over other men’s shoulders or designed for close-combat bayonet fighting, military rifles could be much shorter than muskets, which also made loading from the muzzle easier and reduced the difficulties associated with fitting the bullet into the barrel, although the rate of fire was still slower than that of a musket.

Various rifled musket projectiles

The problem of slow loading of rifles caused by barrel fouling was solved by the Minié ball, which was invented in the 1840s by French inventor Claude-Étienne Minié. Despite its name, the Minié ball was not a round ball at all - it was long and conical, with an expanding skirt at the rear of the bullet. The skirt allowed the minié ball to be smaller than the barrel's bore, so it would slip in as easily as the ball of a smoothbore. When the weapon was fired, the skirt expanded to fit tightly against the inside of the rifle barrel, with less energy wasted in blow-by around the projectile and insuring that the rifling lands and grooves would impart a stabilizing spin to the minié ball.^[5]

In the 1840s and 1850s, many smoothbore muskets had their barrels replaced with similar barrels that were rifled so that they could fire the new bullet. These "rifled muskets" or "rifle muskets" were long enough to serve the function of muskets in close formations of line and square, were as quick to load as the old muskets and as easy to use with minimal training. Yet the Minié-type rifled muskets were much more accurate than smoothbore muskets. The loose-fitting ball in a smoothbore musket was accurate to ranges of 50 to 75 yards (46 to 69 m) or less. Rifled muskets increased the effective range to about 200 to 300 yards (180 to 270 m), and in the right hands could often hit a man-sized target up to 500 yards (460 m) away.^[6] This potential accuracy, however, required skills only acquired through advanced training and practice; a rifle-musket in the hands of a raw recruit would not have performed very much better than a smoothbore.

In the 1850s and 1860s, new weapons produced with rifled barrels continued to be referred to as "rifled muskets" or "rifle-muskets" even though they had not originally been produced as smoothbore weapons. The term was only used for weapons that directly replaced smoothbore muskets. For example, the Springfield Model 1861 with its typical musket style lock mechanism and long barrel length was called a "rifled musket". In contrast, the Henry Rifle produced in the same time period did not replace a musket and did not have other musket-like characteristics, and was just referred to as a "rifle".

In the late 1860s, rifled muskets were replaced by breech-loading rifles. Weapons like the Springfield Model 1868 were produced by simply changing out the lock mechanism of a rifled musket. However, once this change was made, the weapon was no longer referred to as a rifled-musket and was instead referred to as simply a "rifle".

Characteristics of rifled muskets

In general, rifle muskets were the same length as the smoothbore muskets they replaced. This meant that they typically had a barrel length of about 40 inches (100 cm) and an overall length of about 55 to 60 inches (140 to 150 cm). Period U.S. Armory nomenclature described rifles and rifle-muskets as newly made firearms specifically designed and manufactured with rifling. Rifled muskets were smoothbore firearms returned to the armory or contractors for rifling. Considerable numbers of armory-stored smoothbores were converted in this way in the 1850s upon adoption of the Minié ball as the standard projectile. Rifle muskets tended to be of smaller caliber than their smoothbore predecessors, for example, the .58 caliber U.S. Springfield Model 1855 or the .577 caliber British Pattern 1853 Enfield. Tests conducted by the U.S. Army in the mid-1850s showed that the smaller caliber was more accurate at longer ranges. The cylindro-conical shape of the Minié ball also meant that the smaller-diameter but longer .58 caliber Minié ball had roughly the same amount of lead and weight as the larger .69 round ball. While the caliber was reduced, the overall length of the barrel was not. Shorter rifles could have easily been made (and were made for specific branches or arms such as mounted infantry and riflemen) that would have been more accurate than the smoothbore muskets they replaced, but military commanders still used tactics like firing by ranks, and feared that with a shorter weapon the soldiers in the rear ranks might accidentally shoot the front rank soldiers in the back of the head. Military commanders at the time also believed that bayonet fighting would continue to be important in battles, which also influenced the decision to keep the overall length of the weapon similar to the length of a pike.

In the US and British service standardized infantry firearms were produced in a longer "rifle musket" version and a shorter "rifle" version, such as the Springfield Model 1855. The rifle musket version had a 40-inch barrel and an overall length of 56 inches (140 cm). The rifle version had a 33-inch (84 cm) barrel and an overall length of 49 inches (120 cm).^[7] In the British forces the distinction was retained between the full-length musket issued to the infantry as a whole, and the shorter and handier version of the Enfield produced for specialist rifle regiments and marines. The long version had the barrel held to the stock by three metal bands, while the shorter version needed just two, so they are referred to as “3-band” and “2-band” Enfields respectively.

Rifle muskets typically used percussion lock systems, with some exceptions like the Springfield Model 1855, which also was equipped with the Maynard tape primer system.

Since rifle muskets were meant as a direct replacement for smoothbore muskets, they were fitted with bayonets. Their designers envisioned that they would be used in battle much like the bayonets on older smoothbore muskets. However, in practice, the longer range of the rifle musket and changes in tactics rendered the bayonet almost obsolete. During the U.S. Civil War, bayonets accounted for less than one percent of battlefield casualties. This was a significant change from the days of smoothbore muskets, when bayonets accounted for roughly a third of all battlefield casualties.

In military use, rifle musket loading was simplified somewhat through the use of paper cartridges, which were significantly different from modern metallic cartridges. They typically consisted of rolled-up tubes of paper containing a premeasured amount of black powder and a greased Minié ball. Unlike the smoothbore cartridge, the entire cartridge was not simply shoved into the weapon. Instead, the paper was torn open (typically by the shooter's teeth), the powder was poured down the barrel, the Minié ball was placed into the barrel and rammed down on top of the powder with the ramrod. The paper was discarded. Also differing from a modern cartridge, a separate percussion cap had to be placed onto the percussion lock's cone before the weapon could be fired. The Maynard tape primer system attempted to speed up this last step by using paper strips similar to those used in modern toy cap guns in place of the percussion cap, but this proved to be unreliable in field service and was abandoned on later weapons.

An exception to this method is the Enfield rifle-musket cartridge. There were no lubrication rings moulded or swaged into the Enfield projectile. The projectile was inserted upside down in the cartridge and the outside of the cartridge paper was greased at the projectile end and intended to be inserted and used as a paper patch. A ramrod was used to fully seat the round.

Use in battle

Rifled muskets were heavily used in the American Civil War. The American-made Springfield Model 1861 was the most widely used weapon in the war, followed by the British Pattern 1853 Enfield. The Lorenz rifle was the third most used rifle during the Civil War^[8]

The Enfield was also used in the Crimean War where its greater range was a significant advantage over the much shorter-ranged Russian smoothbore muskets.

However, soldiers armed with rifled muskets were not always successful on the battlefield. In the Italian War of 1859, Austrian troops armed with rifled muskets were defeated by French forces using aggressive skirmishing tactics and rapid bayonet assaults at close range.^[9]

See also

• Muzzle-loading rifle
• Springfield rifle

References

External links

• The Enfield Pattern 1853 through to its culmination as the Snider MkIII
• Rifle Musket and Minié Ball
• The Enfield Pattern 1856 Rifle Musket