Terephthalic acid

Terephthalic acid
Names
Preferred IUPAC name
Benzene-1,4-dicarboxylic acid
Other names
1,4-Benzenedioic acid
Benzene-1,4-dioic acid
Terephthalic acid
para-Phthalic acid
TPA
PTA
BDC
Identifiers
3D model (JSmol)
3DMet B00943
1909333
ChEBI
ChEMBL
ChemSpider
ECHA InfoCard 100.002.573
EC Number 202-830-0
50561
KEGG
RTECS number WZ0875000
UNII
Properties
C8H6O4
Molar mass 166.13 g·mol−1
Appearance White crystals or powder
Density 1.522 g/cm3
Melting point 427 °C (801 °F; 700 K) in a sealed tube. Sublimes at standard atmospheric pressure.
Boiling point Decomposes
0.0015 g/100 mL at 20 °C
Solubility polar organic solvents aqueous base
Acidity (pKa) 3.51, 4.82[1]
−83.51×10−6 cm3/mol
Structure
0
Hazards
Safety data sheet See: data page
MSDS sheet
GHS pictograms
GHS signal word Warning
H315, H319, H335
P261, P264, P271, P280, P302+352, P304+340, P305+351+338, P312, P321, P332+313, P337+313, P362, P403+233, P405, P501
Related compounds
Phthalic acid
Isophthalic acid
Benzoic acid
p-Toluic acid
Related compounds
p-Xylene
Polyethylene terephthalate
Dimethyl terephthalate
Supplementary data page
Refractive index (n),
Dielectric constantr), etc.
Thermodynamic
data
Phase behaviour
solidliquidgas
UV, IR, NMR, MS
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
☒N verify (what is ☑Y☒N ?)
Infobox references

Terephthalic acid is an organic compound with formula C6H4(CO2H)2. This white solid is a commodity chemical, used principally as a precursor to the polyester PET, used to make clothing and plastic bottles. Several million tonnes are produced annually.[2] The common name is derived from the turpentine-producing tree Pistacia terebinthus and phthalic acid.

History

Terephthalic acid was first isolated (from turpentine) by the French chemist Amédée Cailliot (1805–1884) in 1846.[3] Terephthalic acid became industrially important after World War II. The first companies to commercialize fibers made from polyethylene terephthalate were Imperial Chemical Industries in the UK in 1949 and DuPont in the US in 1953. The fibers were made from dimethyl terephthalate by transesterification with ethylene glycol. Terephthalic acid was produced by oxidation of p-xylene with dilute nitric acid. This type of oxidation involved the use of air in the initial oxidation step to minimize the consumption of nitric acid and difficulty in purification. Growth in the textile industry led to increase in demand of TPA. In the 1960s, all the terephthalic acid produced was converted to its dimethyl ester, since TPA was infusible and difficult to purify. Presently TPA is manufactured by oxidation of p-xylene.

Solubility

Terephthalic acid is poorly soluble in water and alcohols; consequently, until about 1970 terephthalic acid was purified as its dimethyl ester. It sublimes when heated.

Solubility (g/100 g solvent)
Solvent25 °C120 °C160 °C200 °C240 °C
Methanol0.12.915
Water0.00190.080.381.79.0
Acetic acid0.0350.30.751.84.5
Formic acid0.5
Sulphuric acid2
Dimethyl formamide6.7
Dimethyl sulfoxide20
Vapor pressure
Temperature
(°C)
Pressure
(kPa)
3031.3
35313.3
37026.7
38753.3
404101.3

Production

Amoco process

In the Amoco process, terephthalic acid is produced by oxidation of p-xylene by oxygen in air:

The process uses a cobaltmanganesebromide catalyst. The bromide source can be sodium bromide, hydrogen bromide or tetrabromoethane where bromine functions as a regenerative source of free radicals. In this process, acetic acid is the solvent and oxygen from compressed air is the oxidant. The combination of bromine and acetic acid is found to be highly corrosive and hence the equipment is lined with titanium. A feed mixture containing p-xylene, acetic acid, the catalyst system, and compressed air is fed to a reactor. The oxidation of the methyl group takes place in two steps where p-xylene is converted to p-toluic acid and the byproduct undesirable 4-formylbenzoic acid along with crude p-toluic acid. It is further purified to obtain the p-toluic acid with the removal of the 4-formylbenzoic acid using crystallization, centrifugation and filtration. 98% of the p-xylene is reacted to give more than 95 mol% TPA. The solvent losses are comparatively low, and hence the Amoco process is followed by the industries.

This reaction proceeds through a p-toluic acid intermediate which is then oxidized to terephthalic acid. In p-toluic acid, deactivation of the methyl by the electron-withdrawing carboxylic acid group makes the methyl one tenth as reactive as the methyls of xylene itself, making the second oxidation significantly more difficult. [4] The commercial process utilizes acetic acid as solvent and a catalyst composed of cobalt and manganese salts, with a bromide promoter. The yield is nearly quantitative. The most problematic impurity is 4-formylbenzoic acid (commonly known in the field as 4-carboxybenzaldehyde or 4-CBA), which is removed by hydrogenation of a hot aqueous solution. This solution is then cooled in a stepwise manner to crystallize highly pure terephthalic acid.

Despite optimized yields greater than 95% with excellent purity, the synthesis has shortcomings. Due to high reaction temperature, approximately 5% of the acetic acid solvent is lost by decomposition or "burning". Solvent burning is a significant economic factor in the oxidation process. In addition, product loss by decarboxylation to benzoic acid is common. The high temperature diminishes oxygen solubility in an already oxygen-starved system. Pure oxygen cannot be used in the traditional system due to hazards of flammable organic–O2 mixtures. Atmospheric air can be used in its place, but once reacted needs to be purified of toxins and ozone depleters such as methylbromide before being released. Additionally, the corrosive nature of bromides at high temperatures requires the reaction be run in expensive titanium reactors.[5] [6]

Cooxidation

The cooxidation technique uses an auxiliary substance which is simultaneously oxidized to hydrogen peroxide which increases the activity of the oxidation catalyst. Auxiliaries include: acetaldehyde (Toray process, Japan), paraldehyde (Eastman, USA), and methyl ethyl ketone.

Multistage oxidation

This method is developed to reduce the concentration of 4-carboxybenzaldehyde content in the final product to 200–300 ppm without separate purification step. The product is often called "medium-purity TPA". In this method, heating gives increased TPA solubility. At high temperature, TPA crystals constantly dissolve and reform which increases release of 4-carboxybenzaldehyde in solution where oxidation can be completed.

Mitsubishi Process

p-Xylene in acetic acid is oxidized as in the Amoco oxidation using a cobalt–manganese–bromine catalyst. A slurry is heated to 235–290 °C and oxidized further in another reactor.

Eastman Chemical

This method includes two-stage oxidation processes both at 175–230 °C temperature instead of heating between stages. After multistage oxidation, solid–liquid separation and drying to obtain final product is carried out.

Henkel process (Raecke process)

Alternatively, but not commercially significant, is the so-called "Henkel process" or "Raecke process", named after the company and patent holder, respectively. This process involves the rearrangement of phthalic acid to terephthalic acid via the corresponding potassium salts.[7][8] Terephthalic acid can be prepared in the laboratory by oxidizing various para-disubstituted derivatives of benzene, including caraway oil or a mixture of cymene and cuminol with chromic acid.

The use of carbon dioxide overcomes many of the problems with the original industrial process. Because CO2 is a better flame inhibitor than N2, a CO2 environment allows for the use of pure oxygen directly, instead of air, with reduced flammability hazards. The solubility of molecular oxygen in solution is also enhanced in the CO2 environment. Because more oxygen is available to the system, supercritical carbon dioxide (Tc = 31 °C) has more complete oxidation with fewer byproducts, lower carbon monoxide production, less decarboxylation and higher purity than the commercial process.[5][6]

In supercritical water medium, the oxidation can be effectively catalyzed by MnBr2 with pure O2 in a medium-high temperature. Use of supercritical water instead of acetic acid as a solvent diminishes environmental impact and offers a cost advantage. However, the scope of such reaction systems is limited by the even harsher conditions than the industrial process (300−400 °C, >200 bar).[9]

Ketones have been found to act as promoters for formation of the active cobalt(III) catalyst. In particular, ketones with a-methylene groups oxidize to hydroperoxides that are known to oxidize cobalt(II). Viable ketones were butanone, triacetylmethane (TAM), 2,3-pentanedione (2,3-PD), and acetylacetone; all of which can stabilize radical formation through resonance.[5]

Reactions run at temperatures as low as 100 °C are possible by using zirconium salts as a cocatalyst in place of bromide and manganese acetate. It is thought that the zirconium(IV) acts to oxidize Co(II) to the active Co(III). This alone shortens the induction period, and has been shown to have a synergistic effect with ketones. However, a greater amount of cobalt acetate is required than the common industrial process and is ineffective over 160 °C.

The addition of a small portion of metalloporphyrin, in particular T(p-Cl)PPMnCl, has a cocatalytic effect with the traditional Co(OAc)2 catalyst. This requires less acetic acid and does not require bromides. The catalytic effect has been attributed to the ease of peroxide formation over the metalloporphyrin.[4][10]

The autoxidation of p-xylene is known to proceed through a free radical process. Mn(III) and Co(III) alone are not strong enough oxidizers to start the radical chain reaction, but instead initiate it by forming bromine radicals from the ions in solution. These bromine radicals then decompose hydroperoxides that are ligated to the metals as well as abstract hydrogens from the methyl groups on p-xylene to form free radicals and propagate the reaction. The following are the proposed initiation, propagation and terminations steps for the first of four oxidations involved in the auto-oxidation:

The radical chain reaction proceeds through a series of intermediates, starting with the oxidation of p-xylene to p-tolualdehyde (TALD), then p-toluic acid (PT), 4-carboxybenzaldehyde (4-CBA), and finally to the terephthalic acid (TA) product.

The kinetics of the oxidation are exceedingly complex, but a general understanding of the mechanism has been established.[11]

Alternative and past technologies

  • Oxidation of p-xylene with acetic acid solvent and cobalt catalyst with acetaldehyde activator at 120–140 °C with residence time greater than or equal to 2 hours. Bromine is now being used in place of acetaldehyde.
  • Mobil Chemicals in US with above processes used cobalt catalyst with acetic acid solvent and butanone as activator. After reaction, crude TPA was leached by adding pure acetic acid and at high temperature to achieve partial solubility. Final purification was by sublimation and catalytic treatment of the vapor.
  • Henkel technology (not in practice): Starting with phthalic anhydride, monopotassium and dipotassium phthalate salts were formed in sequence. Dipotassium salt was isomerized to dipotassiumterephthalate under carbon dioxide at 1000-5000 kPa and 350-450 °C. This salt was dissolved in water and recycled to the start of process, where TPA crystals formed during production of monopotassium salts.
  • Process by Lummus (now a subsidiary of Chicago Bridge & Iron Company) (not commercialized) using dinitrile route.
  • Process by Eastman (not commercialized) using the formation of 1,4-diiodobenzene with carbonylation to aromatic acids.
  • Process by Mitsubishi Gas Chemicals (not commercialized): Here, a complex between toluene and hydrogen fluoride/boron trifluoride is formed and carbonylated with carbon monoxide to form a p-tolualdehyde complex. After decomposition of complex p-tolualdehyde can be oxidized in water with a manganese–bromine catalyst system to terephthalic acid.
  • Oxidation using nitric acid, but leads to difficulty in purification and NOx emissions.

Applications

  • Polyester fibers based on PTA provide easy fabric care, both alone and in blends with natural and other synthetic fibers. Polyester films are used widely in audio and video recording tapes, data storage tapes, photographic films, labels and other sheet material requiring both dimensional stability and toughness.
  • The PTA derivative, polyethylene terephthalate (PET), has become the primary container resin for applications such as carbonated beverage bottles, while other polyterephthalates provide dimensional stability, good heat resistance and durability for engineering applications.
  • Terephthalic acid is used in paint as a carrier.
  • Terephthalic acid is used as a raw material to make terephthalate plasticizers such as dioctyl terephthalate and dibutyl terephthalate.
  • It is used in the pharmaceutical industry as a raw material for certain drugs.
  • In addition to these end uses, Terephthalic acid based polyesters and polyamides are also used in hot melt adhesives.
  • PTA is an important raw material for lower molecular weight saturated polyesters for powder and water-soluble coatings.

Virtually the entire world's supply of terephthalic acid and dimethyl terephthalate are consumed as precursors to polyethylene terephthalate (PET). World production in 1970 was around 1.75 million tonnes.[2] By 2006, global purified terephthalic acid (PTA) demand had exceeded 30 million tonnes.

There is a smaller, but nevertheless significant, demand for terephthalic acid in the production of polybutylene terephthalate and several other engineering polymers.[12]

In the research laboratory, terephthalic acid has been popularized as a component for the synthesis of metal-organic frameworks.

The analgesic drug oxycodone occasionally comes as a terephthalate salt; however, the more usual salt of oxycodone is the hydrochloride. Pharmacologically, one milligram of terephthalas oxycodonae is equivalent to 1.13 mg of hydrochloridum oxycodonae.

Terephthalic acid is used as a filler in some military smoke grenades, most notably the American M83 smoke grenade and M90 vehicle-employed smoke grenade, producing a thick white smoke that acts as an obscurant in the visual and near-infrared spectrum when burned.

Toxicity

Terephthalic acid and its dimethyl ester have very low toxicity, with LD50s over 1 g/kg (oral, mouse).[2]

References

  1. Brown, H. C.; et al. (1955). Baude, E. A.; Nachod, F. C., eds. Determination of Organic Structures by Physical Methods. New York, NY: Academic Press.
  2. 1 2 3 Sheehan, Richard J., "Terephthalic Acid, Dimethyl Terephthalate, and Isophthalic Acid", Ullmann's Encyclopedia of Industrial Chemistry, Weinheim: Wiley-VCH, doi:10.1002/14356007.a26_193
  3. Cailliot, Amédée (1847). "Études sur l'essence de térébenthine" [Studies of the essence of turpentine]. Annales de Chimie et de Physique (3rd series). 21: 27–40. Terephthalic acid is named on p. 29: "Je désignerai le premier de ces acides, celui qui est insoluble, sous le nom d'acide téréphtalique." (I will designate the first of these acids, which is insoluble, by the name of terephthalic acid.)
  4. 1 2 Xiao, Y.; Luo, W.-P.; Zhang, X.-Y.; Guo, C.-C.; Liu, Q.; Jiang, G.-F.; Li, Q.-H. (2010). "Aerobic Oxidation of p-Toluic Acid to Terephthalic Acid over T(p-Cl)PPMnCl/Co(OAc)2 Under Moderate Conditions". Catalysis Letters. 134 (1–2): 155–161. doi:10.1007/s10562-009-0227-1.
  5. 1 2 3 Zuo, Xiaobin; Subramaniam, Bala; Busch, Daryle H. (2008). "Liquid-Phase Oxidation of Toluene and p-Toluic Acid under Mild Conditions: Synergistic Effects of Cobalt, Zirconium, Ketones, and Carbon Dioxide". Industrial & Engineering Chemistry Research. 47 (3): 546–552. doi:10.1021/ie070896h.
  6. 1 2 Zuo, Xiaobin; Niu, Fenghui; Snavely, Kirk; Subramaniam, Bala; Busch, Daryle H. (2010). "Liquid Phase Oxidation of p-Xylene to Terephthalic Acid at Medium-high Temperatures: Multiple Benefits of CO2-expanded Liquids". Industrial & Engineering Chemistry Research. 12 (2): 260–267. doi:10.1039/B920262E.
  7. Ogata, Yoshiro; Tsuchida, Masaru; Muramoto, Akihiko (1957). "The Preparation of Terephthalic Acid from Phthalic or Benzoic Acid". Journal of the American Chemical Society. 79 (22): 6005–6008. doi:10.1021/ja01579a043.
  8. Ogata, Yoshiro; Hojo, Masaru; Morikawa, Masanobu (1960). "Further Studies on the Preparation of Terephthalic Acid from Phthalic or Benzoic Acid". Journal of Organic Chemistry. 25 (12): 2082–2087. doi:10.1021/jo01082a003.
  9. Pérez, Eduardo; Fraga Dubreuil, Joan; García Verdugo, Eduardo; Hamley, Paul A.; Thomas, W. Barry; Housley, Duncan; Partenheimer, Wait; Poliakoff, Martyn (2011). "Selective Aerobic Oxidation of para-Xylene in Sub- and Supercritical Water. Part 1. Comparison with Ortho-xylene and the Role of the Catalyst". Green Chemistry. 13 (12): 2389–2396. doi:10.1039/C1GC15137A.
  10. Jiang, Quan; Xiao, Yang; Tan, Ze; Li, Qing-Hong; Guo, Can-Cheng (2008). "Aerobic Oxidation of P-xylene over Metalloporphyrin and Cobalt Acetate: Their Synergy and Mechanism". Journal of Molecular Catalysis A: Chemical. 285 (1–2): 162–168. doi:10.1016/j.molcata.2008.01.040.
  11. Wang, Qinbo; Cheng, Youwei; Wang, Lijun; Li, Xi (2007). "Semicontinuous Studies on the Reaction Mechanism and Kinetics for the Liquid-Phase Oxidation of p-Xylene to Terephthalic Acid". Industrial & Engineering Chemistry Research. 46 (26): 8980–8992. doi:10.1021/ie0615584.
  12. Ashford's Dictionary of Industrial Chemicals (3rd ed.). 2011. p. 8805.
  • Tedder, J. M.; Nechvatal, A.; Tubb, A. H., eds. (1975). Basic Organic Chemistry: Part 5, Industrial Products. Chichester, UK: John Wiley & Sons.
  • International Chemical Safety Card 0330

See also

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.