Low-water crossing

Low-water crossing at Chew Stoke
Roanoke River low water crossing
The drovers' road from Abergwesyn to Tregaron, Wales, crosses the Afon Irfon via the Irish bridge at the foot of the Devil's Staircase
The single-lane low-water bridge over the Shenandoah River in Virginia
Shared pedestrian/cycle way over the Yass River in Yass (person for scale)

A low-water crossing (also known as an Irish bridge, causeway in Australia, low-level crossing or low-water bridge) provides a bridge when water flow is low. Under high-flow conditions, water runs over the roadway and precludes vehicular traffic. This approach is cheaper than building a bridge to raise the level of the road above the highest flood stage of a river, particularly in developing countries or in semi-arid areas with rare high-volume rain. Low-water crossings can be dangerous when flooded.

Construction

The low-water crossing was developed from the traditional ford. A ford permits vehicular traffic to cross a waterway with wet wheels. The term “low-water crossing” implies that the crossing is usually dry, while “ford” implies that the crossing is usually wet.

A simple low-water crossing can be constructed with culverts. Culverts (often concrete pipes) are used to carry the water in a stream keeping the crossing surface dry for most of the year. High flows, e.g. spring runoff or flash floods, flow over the top of the crossing, as the culverts are not large enough to carry these flood-type runoff events.

A more elaborate low-water bridge will usually be an engineered concrete structure. There are thousands of such structures in the western United States; some of them accommodate four-lane city streets or highways. Typically, a low-water bridge that accommodates a high daily volume of vehicular traffic will be underwater only a few days per decade.

A low-water bridge renders the waterway non-navigable. In almost all cases this is not a practical concern, since the waterway would be non-navigable except during flood conditions anyway.

A low-water bridge is sometimes called a submersible bridge, but this is a misnomer. A true submersible bridge is used on navigable waterways and is actively lowered into the water.

Safety

The concept behind low-water crossings is that they are convenient and safe to use in normal conditions. Once the water level rises to the point where it crosses the bridge surface the bridge is generally unsafe to use, and in developed countries this will usually be indicated by warning signs. An additional hazard is that the bridge surface may become completely obscured by the water, making it relatively easy to fall off the bridge surface into the deeper and more hazardous water on either side. As a consequence, the line of the submerged bridge is often marked with poles or other structures to indicate its course to unwary travelers and emergency users even when submerged.

The force of the moving water may be strong enough to physically push the vehicle off the bridge: the higher the percentage of the vehicle in the water, the more likely the water's force will take the vehicle off the bridge and send it downriver with substantial damage. An additional risk for trying to cross a bridge under water, especially when more than a couple of feet deep, is the possibility of the vehicle's engine stalling. As people will typically try to then get out of the vehicle, they may step into water currents that cause them to fall or be pulled down into the water. As the current during floods is often quite strong, it may sweep them downriver and carry them into debris, possibly causing injury or death.

Despite the obvious dangers and warnings given there are still a significant number of emergencies and even deaths attributable to the unwary use of low-water bridges during flood conditions.

One attempted solution/deterrent is the Stupid Motorist Law in the American state of Arizona. Drivers who become stranded on flooded low-water bridges are charged with the cost incurred by emergency services to come to their rescue.

Fish passage at low-water crossings

Since 1980, the ecological impact of road crossings on natural streams and rivers has been recognised. Baffles may be installed along the culvert to provide some fish-friendly alternative.[1][2] But baffles can reduce drastically the culvert discharge capacity for a given afflux,[3] thus increasing substantially the total cost of the culvert structure to achieve the same design discharge and afflux, or increasing the risk of road flooding in an existing structure.

See also

External links/references

References

  1. ↑ Olsen, A. and Tullis, B. (2013). "Laboratory Study of Fish Passage and Discharge Capacity in Slip-Lined, Baffled Culverts". Journal of Hydraulic Engineering, ASCE. 139 (4): 424–432. doi:10.1061/(asce)hy.1943-7900.0000697. ISSN 0733-9429.
  2. ↑ Chanson, H. and Uys, W. (2016). "Baffle Designs to Facilitate Fish Passage in Box Culverts: A Preliminary Study". 6th IAHR International Symposium on Hydraulic Structures, Hydraulic Structures and Water System Management: 295–304. doi:10.15142/T300628160828. ISBN 978-1-884575-75-4.
  3. ↑ Larinier, M. (2002). "Fish Passage through Culverts, Rock Weirs and Estuarine Obstructions". Bulletin Français de Pêche et Pisciculture. 364 (18): 119–134.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.