Woodworking joints

A worker uses a mortising machine to shape timber framing joints

Joinery is a part of woodworking that involves joining together pieces of timber or lumber, to produce more complex items. Some wood joints employ fasteners, bindings, or adhesives, while others use only wood elements. The characteristics of wooden joints - strength, flexibility, toughness, appearance, etc. - derive from the properties of the materials involved and the purpose of the joint. Therefore, different joinery techniques are used to meet differing requirements. For example, the joinery used to construct a house can be different from that used to make puzzle toys, although some concepts overlap.

Types of woodworking joints

A worker uses a large circular saw to cut joints.

Traditional woodworking joints

Joint	Image	Description
Butt joint		The end of a piece of wood is butted against another piece of wood. This is the simplest and weakest joint. Of those, there is the a) T-butt, b) end-to-end butt, c) T-lap d) Miter butt and e) edge-to-edge butt.
Lap joint		The end of a piece of wood is laid over and connected to another piece of wood. This is the next simplest and weakest joint.
Bridle joint		Also known as open tenon, open mortise and tenon, or tongue and fork joints, this joint is where the through mortise is open on one side and forms a fork shape. The mate has a through tenon or necked joint. Bridle joints are commonly used to join rafter tops, also used in scarf joints and sometimes sill corner joints in timber framing.
Dowel joint		The end of a piece of wood is butted against another piece of wood. This is reinforced with dowel pins. This joint is quick to make with production line machinery and so is a very common joint in factory-made furniture.
Mitre joint		Similar to a butt joint, but both pieces have been bevelled (usually at a 45 degree angle).
Finger joint		Also known as a box joint, is a corner joint with interlocking fingers. Receives pressure from two directions.
Dovetail joint		A form of box joint where the fingers are locked together by diagonal cuts. More secure than a finger joint.[1]
Dado joint		Also called a housing joint or trench joint, a slot is cut across the grain in one piece for another piece to set into; shelves on a bookshelf having slots cut into the sides of the shelf, for example.
Groove joint		Like the dado joint, except that the slot is cut with the grain.
Tongue and groove		Each piece has a groove cut all along one edge, and a thin, deep ridge (the tongue) on the opposite edge. If the tongue is unattached, it is considered a spline joint.
Mortise and tenon		A stub (the tenon) will fit tightly into a hole cut for it (the mortise). This is a hallmark of Mission Style furniture, and also the traditional method of jointing frame and panel members in doors, windows, and cabinets. This joint is a good strong joint to use.
Birdsmouth joint		Also called a bird's beak cut, this joint used in roof construction. A V-shaped cut in the rafter connects the rafter to the wall-plate.[2]
Cross Lap		A joint in which the two members are joined by removing material from each at the point of intersection so that they overlap.
Splice joint		A joint used to attach two members end to end.

Nontraditional woodworking joints

Joint	Image	Description
Pocket-hole joinery		A hidden screw is driven into the joint at an angle.
biscuit		A wooden oval is glued into two crescent-shaped holes.
Floating tenon joint		See Mortise and tenon
stitch and glue		Wood panels stitched together, usually with copper wire, and glued together with epoxy resin.

Traditional ways of improving joints

A doweled joint

• Dowel: A small rod is used internal to a joint both to help align and to strengthen the joint. Traditional joints are used with natural timbers as they do not need any other materials other than the timber itself. for example: Butt joints. Dowel joints are also useful for pegging together weaker, cheaper composite materials such as laminate-faced chipboard, and where limited woodworking tools are available (since only simple drilled holes are needed to take the dowels).

Properties of wood

Many wood joinery techniques either depend upon or compensate for the fact that wood is anisotropic: its material properties are different along different dimensions.

This must be taken into account when joining wood parts together, otherwise the joint is destined to fail. Gluing boards with the grain running perpendicular to each other is often the reason for split boards, or broken joints. Furniture from the 18th century, while made by master craftsmen, did not take this into account. The result is this masterful work suffers from broken bracket feet, which was often attached with a glue block which ran perpendicular to the base pieces. The glue blocks were fastened with both glue and nails, resulting in unequal expansion and contraction between the pieces. This was also the cause of splitting of wide boards, which were commonly used during that period.

In modern woodworking it is even more critical, as heating and air conditioning cause major changes in the moisture content of the wood. All woodworking joints must take these changes into account, and allow for the resulting movement.^[3]

Materials used for joining

Metal plates are often incorporated into the design where the timber alone would not be strong enough for a given load.

Pin-connected post and beam house framing

• Joints can be designed to hold without the use of glue or fasteners; a pinned mortise and tenon is an example of this.
• Glue is highly effective for joining timber when both surfaces of the joint are edge grain. A properly glued joint may be as strong or stronger than a single piece of wood. However, glue is notably less effective on end-grain surfaces. Animal glue is soluble in water, producing joints that can be disassembled using steam to soften the glue.
• Various mechanical fasteners may be used, the simplest being nails and screws. Glue and fasteners can be used together.

Traditional joinery

Many traditional wood joinery techniques use the distinctive material properties of wood, often without resorting to mechanical fasteners or adhesives. While every culture in which pieces of wood are joined together to make furniture or structures has a joinery tradition, wood joinery techniques have been especially well documented and is celebrated in the Indian, Chinese, European, and Japanese traditions. Because of the physical existence of Indian and Egyptian examples, we know that furniture from the first several dynasties show the use of complex joints, like the Dovetail, over 5,000 years ago. This tradition continued to other later Western styles. The 18th century writer Diderot included over 90 detailed illustrations of wood joints in his comprehensive encyclopedia.^[5] While Western techniques focused on concealment of joinery, the Eastern societies, though later, did not attempt to "hide" their joints. The Japanese and Chinese traditions in particular required the use of hundreds of types of joints. The reason was that nails and glues used did not stand up well to the vastly fluctuating temperatures and humid weather conditions in most of Central and South-East Asia.^[6] As well, the highly resinous woods used in traditional Chinese furniture do not glue well, even if they are cleaned with solvents and attached using modern glues.

Nontraditional joinery

Methods that are not considered traditional joinery have come about in modern times, largely to attempt to simplify the job of the woodworker for various reasons. These include biscuit joints and pocket hole joinery.

See also

• Joiner, a woodworking occupation
• Woodworking
• Cabinet making
• Timber framing
• Shaker tilting chair
• Building construction
• Chinese Wooden Architecture

Footnotes

References

• Lee A. Jesberger (2007). Woodworking Terms and Joints. Pro Woodworking Tips.com
• Bernard Jones (Ed.) (1980). The Complete Woodworker. ISBN 0-89815-022-1
• Peter Korn (1993). Working with Wood. ISBN 1-56158-041-4
• Sam Allen (1990). Wood Joiner's Handbook. Sterling Publishing. ISBN 0-8069-6999-7
• Wolfram Graubner (1992). Encyclopedia of Wood Joints. Taunton Press. ISBN 1-56158-004-X
• US Forestry Service (1985) Water Repellency and Dimensional Stability of Wood http://www.fpl.fs.fed.us/documnts/fplgtr/fplgtr50.pdf

External links

Wikibooks has a book on the topic of: Carpentry/Cabinetry/Joints

Wikimedia Commons has media related to Woodworking joints.

• Pro Woodworking Tips - Woodworking
• British Woodworking Federation - not for profit woodworking body advice on joinery in the UK

Terms and Joints

• Dimensioning woodworking and carpentry joints Craftsmanspace
• List of French timber framing joints, in French language