C-AKv coupler

The C-AKv coupler is a fully automatic center coupler for railway vehicles, which is designed as a replacement for the European UIC standard chain coupler. Its profile is derived from the Willison design as used on the Russian SA3 coupler. The C-AKv coupler is compatible with both the buffers-and-chain setup and the actual SA3 coupler. C-Akv is from German Compact - Automatische Kupplung vereinfacht, meaning Compact automatic coupler simplified. Often the brand name Transpact is used as name for it.

History

In the 1970s a new type of automatic coupler was developed by the European railways. This was called the UIC automatic coupler and represented a West European variant of the AK69e type and the East European Intermat type. It was intended as a full replacement for the buffers-and-chain setup, as the latter is not suitable for heavy loads, very time-consuming to be connected, and requires intensive maintenance. As it would have had to be introduced all across Europe within a very short time frame, this introduction was repeatedly postponed. In addition, the UIC automatic coupler was not compatible with the existing chain couplings, which would have made it particularly difficult for some of the European state railways to carry out this conversion from a budgetary point of view.

It should be noted though, that even though the project was abandoned it did lead to one thing: As such a center coupling will have to handle all the power from pushing (like the buffers in a buffer-and-chain setup), pulling (like the chain in a buffers-and-chain setup) and damping the forces when the train is slowing down or braking. So all of these forces has to be absorbed, so a direct conversion of an older piece of rolling stock (locomotives/engines, various kinds of waggons, etc.) is not possible, changes will be needed. But from around 1970 every piece of rolling stock equipped with buffers-and-chain was prepared for conversion, which can be seen by looking at the square hole behind where the chain is bolted to the piece of rolling stock. So it is basically a matter of removing the chain, mount the new coupler in the hole (or cutout, if you want) and fastening it, and done. Of course, until every piece of rolling stock is converted (or at least those for international traffic)), it will be necessary to keep the buffers to do their previous job (absorbing pushing and braking force) as the chain on an unconverted piece of rolling stock will not be able to do so, and the C-AKv will then do the job of the hook in the buffers-and-chain setup.

The C-AKv coupler was developed by SAB WABCO, now Faiveley Transport Witten GmbH. Unlike the UIC automatic coupler, it is compatible with the existing chain coupler, which would allow for a longer transition period. Since the year 2002, the C-AKv has been on trial on the German railways. It is used on heavy coal block trains between the opencast mines at Profen and the Schkopau power plant.

At this time, the German railways, Faiveley and the Technical University of Berlin are developing possible transition scenarios for a general introduction of the C-AKv coupler.

Heaviest trains

C-AKv coupler on a Class 189 train to pull iron ore

In a field test starting in 2004, the trains on the connection from the brown coal strip mine near Wählitz to the Schkopau Power Station were equipped with C-AKv-couplers which showed that regular wheel replacements shrunk below a third due to reduced wear.[1] The solution has been kept and it spawned further investigations.

Beginning in late 2009, eighteen DBAG Class 189 electric locomotives owned by DB Schenker were converted to C-AKv couplers, in order to handle 6,000 tonne iron ore trains[2] from Rotterdam to the steel works at Dillingen in the Saarland, replacing the previous German class 151 double units and Dutch class 6400 triple units commonly used on these workings previously. As these locomotives are also capable of operating on both the 15 kV AC and 25 kV AC (and 1.5 kV DC, for a short stretch under reduced power) overhead system on the German and Dutch networks, locomotive changes on the Dutch-German border are no longer required. Loaded trains are commonly operated by two 189s in a multiple unit setup, with the wagons retaining the AK69e type couplers they have been fitted with since the 1980s.

Design

Being an evolved version of the UIC AK69e coupler, the C-AKv coupler has the same basic outline as the SA3 coupler. Unlike the Russian SA-3 coupler, however, connectors for brake air lines and - if required - electric conduits are integrated into the coupler, which are automatically connected while coupling up. Also, these pneumatic and electric connectors are compatible with the buffers and chain setup, as opposed to previous types.

Since the brake line and electric connectors are integrated into the coupler's main body rather than in a separate body part below the main body, as had been the case on the AK69e type, it is possible to couple C-AKV equipped stock to stock not thus equipped.

The design is much more compact than the former SA3 coupler. The shape is slightly different from that of the SA-3 coupler, due to an additional alignment horn and the matching pocket on the opposite side. These two components allow for greater vertical stability in two connected C-AKv couplers.

See also

References

  1. ↑ Helge Johanes Stuhr (2013-02-26). "3.4.5 Fallbeispiel Braunkohlependel Wählitz-Schkopau". Untersuchung von Einsatzszenarien einer automatischen Mittelpufferkupplung (Dissertation) (PDF) (in German). Technische Universität Berlin. pp. 46, 47. Retrieved 2017-09-19.
  2. ↑ Jens Chlebowski (2009-03-31). "Mobility Lokomotivenwerk München" (PDF). Siemens. p. 11. Retrieved 2014-08-30.
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.