ASTM A325

ASTM A325 is an ASTM International standard for heavy hex structural bolts, titled Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength. It defines mechanical properties for bolts that range from 1⁄2 to 1 1⁄2 inches (13 to 38 mm) in diameter.[1]

The equivalent metric standard is ASTM A325M, which is titled Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength. It defines mechanical properties for sizes M12–36.[2]

There is also a T version, which is used to refer to fully threaded bolts.[3]

This is a standard set by the standards organization ASTM International, a voluntary standards development organizations that sets technical standards for materials, products, systems, and services.

In 2016, specifications A325 and A490 were officially withdrawn by ASTM and replaced by ASTM F3125. A325 and A490 heavy hex structural bolts are now grades under the new F3125 specification.[4]

Types

The type refers to the type of material used to make the bolt. The standard currently defines two types, however it previously defined the following three:[3]

Note that independent of the material the bolt is quenched and tempered.[5]

Connection types

There are also three connection types defined:[3]

  • SC: A slip critical connection.
  • N: A bearing type connection where the threads are on the shear plane.
  • X: A bearing type connection where the threads are not on the shear plane.

Mechanical properties

Mechanical properties, imperial

These types of bolts are designed to be tightened to near their proof strength, in order to create significant bolt tension. The standard states that the bolts must be tightened to at least 70% of the tensile yield strength. These bolts use the same material as their common cousins (ASTM F568M for metric bolts), but have a thicker and wider head to more effectively distribute the load. This modified geometry is often referred to as heavy hex geometry.[6]

ASTM 325 bolts can be considered equivalent to Grade 8.8 bolts according to ASTM F568M.

For a higher strength version of this type of bolt, see ASTM A490.

Head markings and mechanical properties for imperial sizes[5]
Head markingGradeNominal size range [in]Proof strength [ksi]Yield strength (min) [ksi]Tensile strength (min) [ksi]Core hardness [Rockwell][7]
or [7]Type 1​1⁄2–1 (inc.)8592120C24–35
1–​1 1⁄27481105C19–31
Type 2​1⁄2–18592120C24–35
[8]Type 3​1⁄2–18592120C24–35
1–​1 1⁄27481105C19–31

Mechanical properties, metric

Head markings and mechanical properties for metric sizes[6]
Head markingGradeNominal size range [mm]Proof strength [MPa]Yield strength (min) [MPa]Tensile strength (min) [MPa]Core hardness [Rockwell]
Type 112–36[2]600660830C23–34
Type 2
Type 3

/mm

See also

References

  1. ↑ ASTM A325 - 09, retrieved 2009-06-13 .
  2. 1 2 ASTM A325M - 09, retrieved 2009-06-13 .
  3. 1 2 3 ASTM A325, retrieved 2009-06-13 .
  4. ↑ http://www.portlandbolt.com
  5. 1 2 3 ASTM, SAE and ISO grade markings and mechanical properties for steel fasteners, retrieved 2009-06-06 .
  6. 1 2 Metric structural fasteners, archived from the original on 1999-04-21, retrieved 2009-06-06 .
  7. 1 2 Grade Markings: Carbon Steel Bolts, retrieved 2009-05-30 .
  8. ↑ Other markings may be used to denote atmospheric corrosion resistant material
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.