Nuclear fusion

Nuclear fusion is a reaction in which two or more atomic nuclei are combined to form one or more different atomic nuclei and subatomic particles (neutrons or protons). The difference in mass between the reactants and products is manifested as either the release or absorption of energy. This difference in mass arises due to the difference in atomic "binding energy" between the atomic nuclei before and after the reaction. Fusion is the process that powers active or "main sequence" stars, or other high magnitude stars.

The Sun is a main-sequence star, and thus generates its energy by nuclear fusion of hydrogen nuclei into helium. In its core, the Sun fuses 500 million metric tons of hydrogen each second.
The nuclear binding energy curve. The formation of nuclei with masses up to iron-56 releases energy, as illustrated above.

A fusion process that produces nuclei lighter than iron-56 or nickel-62 will generally release energy. These elements have relatively small mass per nucleon and large binding energy per nucleon. Fusion of nuclei lighter than these releases energy (an exothermic process), while fusion of heavier nuclei results in energy retained by the product nucleons, and the resulting reaction is endothermic. The opposite is true for the reverse process, nuclear fission. This means that the lighter elements, such as hydrogen and helium, are in general more fusible; while the heavier elements, such as uranium, thorium and plutonium, are more fissionable. The extreme astrophysical event of a supernova can produce enough energy to fuse nuclei into elements heavier than iron.

In 1920, Arthur Eddington suggested hydrogen-helium fusion could be the primary source of stellar energy. Quantum tunneling was discovered by Friedrich Hund in 1929, and shortly afterwards Robert Atkinson and Fritz Houtermans used the measured masses of light elements to show that large amounts of energy could be released by fusing small nuclei. Building on the early experiments in nuclear transmutation by Ernest Rutherford, laboratory fusion of hydrogen isotopes was accomplished by Mark Oliphant in 1932. In the remainder of that decade, the theory of the main cycle of nuclear fusion in stars was worked out by Hans Bethe. Research into fusion for military purposes began in the early 1940s as part of the Manhattan Project. Fusion was accomplished in 1951 with the Greenhouse Item nuclear test. Nuclear fusion on a large scale in an explosion was first carried out on 1 November 1952, in the Ivy Mike hydrogen bomb test.

Research into developing controlled fusion inside fusion reactors has been ongoing since the 1940s, but the technology is still in its development phase.

Process

Fusion of deuterium with tritium creating helium-4, freeing a neutron, and releasing 17.59 MeV as kinetic energy of the products while a corresponding amount of mass disappears, in agreement with kinetic E = Δmc2, where Δm is the decrease in the total rest mass of particles.[1]

The release of energy with the fusion of light elements is due to the interplay of two opposing forces: the nuclear force, which combines together protons and neutrons, and the Coulomb force, which causes protons to repel each other. Protons are positively charged and repel each other by the Coulomb force, but they can nonetheless stick together, demonstrating the existence of another, short-range, force referred to as nuclear attraction.[2] Light nuclei (or nuclei smaller than iron and nickel) are sufficiently small and proton-poor allowing the nuclear force to overcome repulsion. This is because the nucleus is sufficiently small that all nucleons feel the short-range attractive force at least as strongly as they feel the infinite-range Coulomb repulsion. Building up nuclei from lighter nuclei by fusion releases the extra energy from the net attraction of particles. For larger nuclei, however, no energy is released, since the nuclear force is short-range and cannot continue to act across longer nuclear length scales. Thus, energy is not released with the fusion of such nuclei; instead, energy is required as input for such processes.

Fusion powers stars and produces virtually all elements in a process called nucleosynthesis. The Sun is a main-sequence star, and, as such, generates its energy by nuclear fusion of hydrogen nuclei into helium. In its core, the Sun fuses 620 million metric tons of hydrogen and makes 606 million metric tons of helium each second. The fusion of lighter elements in stars releases energy and the mass that always accompanies it. For example, in the fusion of two hydrogen nuclei to form helium, 0.7% of the mass is carried away in the form of kinetic energy of an alpha particle or other forms of energy, such as electromagnetic radiation.[3]

It takes considerable energy to force nuclei to fuse, even those of the lightest element, hydrogen. When accelerated to high enough speeds, nuclei can overcome this electrostatic repulsion and be brought close enough such that the attractive nuclear force is greater than the repulsive Coulomb force. The strong force grows rapidly once the nuclei are close enough, and the fusing nucleons can essentially "fall" into each other and the result is fusion and net energy produced. The fusion of lighter nuclei, which creates a heavier nucleus and often a free neutron or proton, generally releases more energy than it takes to force the nuclei together; this is an exothermic process that can produce self-sustaining reactions.

Energy released in most nuclear reactions is much larger than in chemical reactions, because the binding energy that holds a nucleus together is greater than the energy that holds electrons to a nucleus. For example, the ionization energy gained by adding an electron to a hydrogen nucleus is 13.6 eV—less than one-millionth of the 17.6 MeV released in the deuteriumtritium (D–T) reaction shown in the adjacent diagram. Fusion reactions have an energy density many times greater than nuclear fission; the reactions produce far greater energy per unit of mass even though individual fission reactions are generally much more energetic than individual fusion ones, which are themselves millions of times more energetic than chemical reactions. Only direct conversion of mass into energy, such as that caused by the annihilatory collision of matter and antimatter, is more energetic per unit of mass than nuclear fusion. (The complete conversion of one gram of matter would release 9×1013 joules of energy.)

Research into using fusion for the production of electricity has been pursued for over 60 years. Although controlled fusion is generally manageable with current technology (e.g. fusors), successful accomplishment of economic fusion has been stymied by scientific and technological difficulties; nonetheless, important progress has been made. At present, controlled fusion reactions have been unable to produce break-even (self-sustaining) controlled fusion.[4] The two most advanced approaches for it are magnetic confinement (toroid designs) and inertial confinement (laser designs).

Workable designs for a toroidal reactor that theoretically will deliver ten times more fusion energy than the amount needed to heat plasma to the required temperatures are in development (see ITER). The ITER facility is expected to finish its construction phase in 2025. It will start commissioning the reactor that same year and initiate plasma experiments in 2025, but is not expected to begin full deuterium-tritium fusion until 2035.[5]

Similarly, Canadian-based General Fusion, which is developing a magnetized target fusion nuclear energy system, aims to build its demonstration plant by 2025.[6]

The US National Ignition Facility, which uses laser-driven inertial confinement fusion, was designed with a goal of break-even fusion; the first large-scale laser target experiments were performed in June 2009 and ignition experiments began in early 2011.[7][8]

Nuclear fusion in stars

The proton-proton chain reaction, branch I, dominates in stars the size of the Sun or smaller.
The CNO cycle dominates in stars heavier than the Sun.

An important fusion process is the stellar nucleosynthesis that powers stars, including the Sun. In the 20th century, it was recognized that the energy released from nuclear fusion reactions accounted for the longevity of stellar heat and light. The fusion of nuclei in a star, starting from its initial hydrogen and helium abundance, provides that energy and synthesizes new nuclei as a byproduct of the fusion process. Different reaction chains are involved, depending on the mass of the star (and therefore the pressure and temperature in its core).

Around 1920, Arthur Eddington anticipated the discovery and mechanism of nuclear fusion processes in stars, in his paper The Internal Constitution of the Stars.[9][10] At that time, the source of stellar energy was a complete mystery; Eddington correctly speculated that the source was fusion of hydrogen into helium, liberating enormous energy according to Einstein's equation E = mc2. This was a particularly remarkable development since at that time fusion and thermonuclear energy, and even that stars are largely composed of hydrogen (see metallicity), had not yet been discovered. Eddington's paper, based on knowledge at the time, reasoned that:

  1. The leading theory of stellar energy, the contraction hypothesis, should cause stars' rotation to visibly speed up due to conservation of angular momentum. But observations of Cepheid variable stars showed this was not happening.
  2. The only other known plausible source of energy was conversion of matter to energy; Einstein had shown some years earlier that a small amount of matter was equivalent to a large amount of energy.
  3. Francis Aston had also recently shown that the mass of a helium atom was about 0.8% less than the mass of the four hydrogen atoms which would, combined, form a helium atom, suggesting that if such a combination could happen, it would release considerable energy as a byproduct.
  4. If a star contained just 5% of fusible hydrogen, it would suffice to explain how stars got their energy. (We now know that most 'ordinary' stars contain far more than 5% hydrogen)
  5. Further elements might also be fused, and other scientists had speculated that stars were the "crucible" in which light elements combined to create heavy elements, but without more accurate measurements of their atomic masses nothing more could be said at the time.

All of these speculations were proven correct in the following decades.

The primary source of solar energy, and similar size stars, is the fusion of hydrogen to form helium (the proton-proton chain reaction), which occurs at a solar-core temperature of 14 million kelvin. The net result is the fusion of four protons into one alpha particle, with the release of two positrons and two neutrinos (which changes two of the protons into neutrons), and energy. In heavier stars, the CNO cycle and other processes are more important. As a star uses up a substantial fraction of its hydrogen, it begins to synthesize heavier elements. The heaviest elements are synthesized by fusion that occurs as a more massive star undergoes a violent supernova at the end of its life, a process known as supernova nucleosynthesis.

Requirements

A substantial energy barrier of electrostatic forces must be overcome before fusion can occur. At large distances, two naked nuclei repel one another because of the repulsive electrostatic force between their positively charged protons. If two nuclei can be brought close enough together, however, the electrostatic repulsion can be overcome by the quantum effect in which nuclei can tunnel through coulomb forces.

When a nucleon such as a proton or neutron is added to a nucleus, the nuclear force attracts it to all the other nucleons of the nucleus (if the atom is small enough), but primarily to its immediate neighbours due to the short range of the force. The nucleons in the interior of a nucleus have more neighboring nucleons than those on the surface. Since smaller nuclei have a larger surface area-to-volume ratio, the binding energy per nucleon due to the nuclear force generally increases with the size of the nucleus but approaches a limiting value corresponding to that of a nucleus with a diameter of about four nucleons. It is important to keep in mind that nucleons are quantum objects. So, for example, since two neutrons in a nucleus are identical to each other, the goal of distinguishing one from the other, such as which one is in the interior and which is on the surface, is in fact meaningless, and the inclusion of quantum mechanics is therefore necessary for proper calculations.

The electrostatic force, on the other hand, is an inverse-square force, so a proton added to a nucleus will feel an electrostatic repulsion from all the other protons in the nucleus. The electrostatic energy per nucleon due to the electrostatic force thus increases without limit as nuclei atomic number grows.

The electrostatic force between the positively charged nuclei is repulsive, but when the separation is small enough, the quantum effect will tunnel through the wall. Therefore, the prerequisite for fusion is that the two nuclei be brought close enough together for a long enough time for quantum tunnelling to act.

The net result of the opposing electrostatic and strong nuclear forces is that the binding energy per nucleon generally increases with increasing size, up to the elements iron and nickel, and then decreases for heavier nuclei. Eventually, the binding energy becomes negative and very heavy nuclei (all with more than 208 nucleons, corresponding to a diameter of about 6 nucleons) are not stable. The four most tightly bound nuclei, in decreasing order of binding energy per nucleon, are 62
Ni
, 58
Fe
, 56
Fe
, and 60
Ni
.[11] Even though the nickel isotope, 62
Ni
, is more stable, the iron isotope 56
Fe
is an order of magnitude more common. This is due to the fact that there is no easy way for stars to create 62
Ni
through the alpha process.

An exception to this general trend is the helium-4 nucleus, whose binding energy is higher than that of lithium, the next heaviest element. This is because protons and neutrons are fermions, which according to the Pauli exclusion principle cannot exist in the same nucleus in exactly the same state. Each proton or neutron's energy state in a nucleus can accommodate both a spin up particle and a spin down particle. Helium-4 has an anomalously large binding energy because its nucleus consists of two protons and two neutrons (it is a doubly magic nucleus), so all four of its nucleons can be in the ground state. Any additional nucleons would have to go into higher energy states. Indeed, the helium-4 nucleus is so tightly bound that it is commonly treated as a single quantum mechanical particle in nuclear physics, namely, the alpha particle.

The situation is similar if two nuclei are brought together. As they approach each other, all the protons in one nucleus repel all the protons in the other. Not until the two nuclei actually come close enough for long enough so the strong nuclear force can take over (by way of tunneling) is the repulsive electrostatic force overcome. Consequently, even when the final energy state is lower, there is a large energy barrier that must first be overcome. It is called the Coulomb barrier.

The Coulomb barrier is smallest for isotopes of hydrogen, as their nuclei contain only a single positive charge. A diproton is not stable, so neutrons must also be involved, ideally in such a way that a helium nucleus, with its extremely tight binding, is one of the products.

Using deuterium–tritium fuel, the resulting energy barrier is about 0.1 MeV. In comparison, the energy needed to remove an electron from hydrogen is 13.6 eV, about 7500 times less energy. The (intermediate) result of the fusion is an unstable 5He nucleus, which immediately ejects a neutron with 14.1 MeV. The recoil energy of the remaining 4He nucleus is 3.5 MeV, so the total energy liberated is 17.6 MeV. This is many times more than what was needed to overcome the energy barrier.

The fusion reaction rate increases rapidly with temperature until it maximizes and then gradually drops off. The DT rate peaks at a lower temperature (about 70 keV, or 800 million kelvin) and at a higher value than other reactions commonly considered for fusion energy.

The reaction cross section (σ) is a measure of the probability of a fusion reaction as a function of the relative velocity of the two reactant nuclei. If the reactants have a distribution of velocities, e.g. a thermal distribution, then it is useful to perform an average over the distributions of the product of cross section and velocity. This average is called the 'reactivity', denoted <σv>. The reaction rate (fusions per volume per time) is <σv> times the product of the reactant number densities:

If a species of nuclei is reacting with a nucleus like itself, such as the DD reaction, then the product must be replaced by .

increases from virtually zero at room temperatures up to meaningful magnitudes at temperatures of 10–100 keV. At these temperatures, well above typical ionization energies (13.6 eV in the hydrogen case), the fusion reactants exist in a plasma state.

The significance of as a function of temperature in a device with a particular energy confinement time is found by considering the Lawson criterion. This is an extremely challenging barrier to overcome on Earth, which explains why fusion research has taken many years to reach the current advanced technical state.[12]

Artificial fusion

Thermonuclear fusion

If matter is sufficiently heated (hence being plasma) and confined, fusion reactions may occur due to collisions with extreme thermal kinetic energies of the particles. Thermonuclear weapons produce what amounts to an uncontrolled release of fusion energy. Controlled thermonuclear fusion concepts use magnetic fields to confine the plasma.

Inertial confinement fusion

Inertial confinement fusion (ICF) is a method aimed at releasing fusion energy by heating and compressing a fuel target, typically a pellet containing deuterium and tritium.

Inertial electrostatic confinement

Inertial electrostatic confinement is a set of devices that use an electric field to heat ions to fusion conditions. The most well known is the fusor. Starting in 1999, a number of amateurs have been able to do amateur fusion using these homemade devices.[13][14][15][16] Other IEC devices include: the Polywell, MIX POPS[17] and Marble concepts.[18]

Beam-beam or beam-target fusion

If the energy to initiate the reaction comes from accelerating one of the nuclei, the process is called beam-target fusion; if both nuclei are accelerated, it is beam-beam fusion.

Accelerator-based light-ion fusion is a technique using particle accelerators to achieve particle kinetic energies sufficient to induce light-ion fusion reactions. Accelerating light ions is relatively easy, and can be done in an efficient manner—requiring only a vacuum tube, a pair of electrodes, and a high-voltage transformer; fusion can be observed with as little as 10 kV between the electrodes. The key problem with accelerator-based fusion (and with cold targets in general) is that fusion cross sections are many orders of magnitude lower than Coulomb interaction cross sections. Therefore, the vast majority of ions expend their energy emitting bremsstrahlung radiation and the ionization of atoms of the target. Devices referred to as sealed-tube neutron generators are particularly relevant to this discussion. These small devices are miniature particle accelerators filled with deuterium and tritium gas in an arrangement that allows ions of those nuclei to be accelerated against hydride targets, also containing deuterium and tritium, where fusion takes place, releasing a flux of neutrons. Hundreds of neutron generators are produced annually for use in the petroleum industry where they are used in measurement equipment for locating and mapping oil reserves.

To overcome the problem of bremsstrahlung radiation in Beam-target fusion, a combinatorial approach has been suggested by Tri-Alpha and Helion energy companies, this method is based on interpenetration of two oppositely directed plasmoids.[19] Theoretical works represent that by creating and warming two accelerated head-on colliding plasmoids up to some kilo electron volts thermal energy which is low in comparison with that of required for thermonuclear fusion, net fusion gain is possible even with aneutronic fuels such as p-11B. In order to attain the necessary conditions of break-even by this method the accelerated plasmoids must have enough colliding velocities of the order of some thousands of kilometers per second (106 m/s) depending on the kind of fusion fuel.[20] In addition, the plasmoids density must be between the inertial and magnetic fusion criteria.

Muon-catalyzed fusion

Muon-catalyzed fusion is a fusion process that occurs at ordinary temperatures. It was studied in detail by Steven Jones in the early 1980s. Net energy production from this reaction has been unsuccessful because of the high energy required to create muons, their short 2.2 µs half-life, and the high chance that a muon will bind to the new alpha particle and thus stop catalyzing fusion.[21]

Other principles

The Tokamak à configuration variable, research fusion reactor, at the École Polytechnique Fédérale de Lausanne (Switzerland).

Some other confinement principles have been investigated.

  • Antimatter-initialized fusion uses small amounts of antimatter to trigger a tiny fusion explosion. This has been studied primarily in the context of making nuclear pulse propulsion, and pure fusion bombs feasible. This is not near becoming a practical power source, due to the cost of manufacturing antimatter alone.
  • Pyroelectric fusion was reported in April 2005 by a team at UCLA. The scientists used a pyroelectric crystal heated from −34 to 7 °C (−29 to 45 °F), combined with a tungsten needle to produce an electric field of about 25 gigavolts per meter to ionize and accelerate deuterium nuclei into an erbium deuteride target. At the estimated energy levels,[22] the D-D fusion reaction may occur, producing helium-3 and a 2.45 MeV neutron. Although it makes a useful neutron generator, the apparatus is not intended for power generation since it requires far more energy than it produces.[23][24][25][26]
  • Hybrid nuclear fusion-fission (hybrid nuclear power) is a proposed means of generating power by use of a combination of nuclear fusion and fission processes. The concept dates to the 1950s, and was briefly advocated by Hans Bethe during the 1970s, but largely remained unexplored until a revival of interest in 2009, due to the delays in the realization of pure fusion.[27]
  • Project PACER, carried out at Los Alamos National Laboratory (LANL) in the mid-1970s, explored the possibility of a fusion power system that would involve exploding small hydrogen bombs (fusion bombs) inside an underground cavity. As an energy source, the system is the only fusion power system that could be demonstrated to work using existing technology. However it would also require a large, continuous supply of nuclear bombs, making the economics of such a system rather questionable.
  • Bubble fusion (Debunked) also called sonofusion was a proposed mechanism for achieving fusion via sonic cavitation which rose to prominence in the early 2000s. Subsequent attempts at replication failed and the principal investigator, Rusi Taleyarkhan, was judged guilty of research misconduct in 2008.[28]

Important reactions

Stellar reaction chains

At the temperatures and densities in stellar cores the rates of fusion reactions are notoriously slow. For example, at solar core temperature (T ≈ 15 MK) and density (160 g/cm3), the energy release rate is only 276 μW/cm3—about a quarter of the volumetric rate at which a resting human body generates heat.[29] Thus, reproduction of stellar core conditions in a lab for nuclear fusion power production is completely impractical. Because nuclear reaction rates depend on density as well as temperature and most fusion schemes operate at relatively low densities, those methods are strongly dependent on higher temperatures. The fusion rate as a function of temperature (exp(−E/kT)), leads to the need to achieve temperatures in terrestrial reactors 10–100 times higher temperatures than in stellar interiors: T ≈ 0.1–1.0×109 K.

Criteria and candidates for terrestrial reactions

In artificial fusion, the primary fuel is not constrained to be protons and higher temperatures can be used, so reactions with larger cross-sections are chosen. Another concern is the production of neutrons, which activate the reactor structure radiologically, but also have the advantages of allowing volumetric extraction of the fusion energy and tritium breeding. Reactions that release no neutrons are referred to as aneutronic.

To be a useful energy source, a fusion reaction must satisfy several criteria. It must:

Be exothermic
This limits the reactants to the low Z (number of protons) side of the curve of binding energy. It also makes helium 4
He
the most common product because of its extraordinarily tight binding, although 3
He
and 3
H
also show up.
Involve low atomic number (Z) nuclei
This is because the electrostatic repulsion that must be overcome before the nuclei are close enough to fuse is directly related to the number of protons it contains - its atomic number.
Have two reactants
At anything less than stellar densities, three body collisions are too improbable. In inertial confinement, both stellar densities and temperatures are exceeded to compensate for the shortcomings of the third parameter of the Lawson criterion, ICF's very short confinement time.
Have two or more products
This allows simultaneous conservation of energy and momentum without relying on the electromagnetic force.
Conserve both protons and neutrons
The cross sections for the weak interaction are too small.

Few reactions meet these criteria. The following are those with the largest cross sections:[30]

(1) 2
1
D
 
+ 3
1
T
 
 4
2
He
 
( 3.5 MeV ) + n0 ( 14.1 MeV )
(2i) 2
1
D
 
+ 2
1
D
 
 3
1
T
 
( 1.01 MeV ) + p+ ( 3.02 MeV )      50%
(2ii)     3
2
He
 
( 0.82 MeV ) + n0 ( 2.45 MeV )      50%
(3) 2
1
D
 
+ 3
2
He
 
 4
2
He
 
( 3.6 MeV ) + p+ ( 14.7 MeV )
(4) 3
1
T
 
+ 3
1
T
 
 4
2
He
 
   + 2 n0      + 11.3 MeV
(5) 3
2
He
 
+ 3
2
He
 
 4
2
He
 
   + 2 p+      + 12.9 MeV
(6i) 3
2
He
 
+ 3
1
T
 
 4
2
He
 
   + p+ + n0    + 12.1 MeV  57%
(6ii)     4
2
He
 
( 4.8 MeV ) + 2
1
D
 
( 9.5 MeV )      43%
(7i) 2
1
D
 
+ 6
3
Li
 
 2 4
2
He
 
+ 22.4 MeV
(7ii)     3
2
He
 
+ 4
2
He
 
 + n0      + 2.56 MeV
(7iii)     7
3
Li
 
+ p+         + 5.0 MeV
(7iv)     7
4
Be
 
+ n0         + 3.4 MeV
(8) p+ + 6
3
Li
 
 4
2
He
 
( 1.7 MeV ) + 3
2
He
 
( 2.3 MeV )
(9) 3
2
He
 
+ 6
3
Li
 
 2 4
2
He
 
+ p+         + 16.9 MeV
(10) p+ + 11
5
B
 
 3 4
2
He
 
          + 8.7 MeV

For reactions with two products, the energy is divided between them in inverse proportion to their masses, as shown. In most reactions with three products, the distribution of energy varies. For reactions that can result in more than one set of products, the branching ratios are given.

Some reaction candidates can be eliminated at once. The D-6Li reaction has no advantage compared to p+-11
5
B
because it is roughly as difficult to burn but produces substantially more neutrons through 2
1
D
-2
1
D
side reactions. There is also a p+-7
3
Li
reaction, but the cross section is far too low, except possibly when Ti > 1 MeV, but at such high temperatures an endothermic, direct neutron-producing reaction also becomes very significant. Finally there is also a p+-9
4
Be
reaction, which is not only difficult to burn, but 9
4
Be
can be easily induced to split into two alpha particles and a neutron.

In addition to the fusion reactions, the following reactions with neutrons are important in order to "breed" tritium in "dry" fusion bombs and some proposed fusion reactors:

n0 + 6
3
Li
 
 3
1
T
 
+ 4
2
He
+ 4.784 MeV
n0 + 7
3
Li
 
 3
1
T
 
+ 4
2
He
+ n0 – 2.467 MeV

The latter of the two equations was unknown when the U.S. conducted the Castle Bravo fusion bomb test in 1954. Being just the second fusion bomb ever tested (and the first to use lithium), the designers of the Castle Bravo "Shrimp" had understood the usefulness of 6Li in tritium production, but had failed to recognize that 7Li fission would greatly increase the yield of the bomb. While 7Li has a small neutron cross-section for low neutron energies, it has a higher cross section above 5 MeV.[31] The 15 Mt yield was 150% greater than the predicted 6 Mt and caused unexpected exposure to fallout.

To evaluate the usefulness of these reactions, in addition to the reactants, the products, and the energy released, one needs to know something about the nuclear cross section. Any given fusion device has a maximum plasma pressure it can sustain, and an economical device would always operate near this maximum. Given this pressure, the largest fusion output is obtained when the temperature is chosen so that <σv>/T2 is a maximum. This is also the temperature at which the value of the triple product nTτ required for ignition is a minimum, since that required value is inversely proportional to <σv>/T2 (see Lawson criterion). (A plasma is "ignited" if the fusion reactions produce enough power to maintain the temperature without external heating.) This optimum temperature and the value of <σv>/T2 at that temperature is given for a few of these reactions in the following table.

fuelT [keV]<σv>/T2 [m3/s/keV2]
2
1
D
-3
1
T
13.61.24×10−24
2
1
D
-2
1
D
151.28×10−26
2
1
D
-3
2
He
582.24×10−26
p+-6
3
Li
661.46×10−27
p+-11
5
B
1233.01×10−27

Note that many of the reactions form chains. For instance, a reactor fueled with 3
1
T
and 3
2
He
creates some 2
1
D
, which is then possible to use in the 2
1
D
-3
2
He
reaction if the energies are "right". An elegant idea is to combine the reactions (8) and (9). The 3
2
He
from reaction (8) can react with 6
3
Li
in reaction (9) before completely thermalizing. This produces an energetic proton, which in turn undergoes reaction (8) before thermalizing. Detailed analysis shows that this idea would not work well, but it is a good example of a case where the usual assumption of a Maxwellian plasma is not appropriate.

Neutronicity, confinement requirement, and power density

Any of the reactions above can in principle be the basis of fusion power production. In addition to the temperature and cross section discussed above, we must consider the total energy of the fusion products Efus, the energy of the charged fusion products Ech, and the atomic number Z of the non-hydrogenic reactant.

Specification of the 2
1
D
-2
1
D
reaction entails some difficulties, though. To begin with, one must average over the two branches (2i) and (2ii). More difficult is to decide how to treat the 3
1
T
and 3
2
He
products. 3
1
T
burns so well in a deuterium plasma that it is almost impossible to extract from the plasma. The 2
1
D
-3
2
He
reaction is optimized at a much higher temperature, so the burnup at the optimum 2
1
D
-2
1
D
temperature may be low. Therefore, it seems reasonable to assume the 3
1
T
but not the 3
2
He
gets burned up and adds its energy to the net reaction, which means the total reaction would be the sum of (2i), (2ii), and (1):

5 2
1
D
4
2
He
+ 2 n0 + 3
2
He
+ p+, Efus = 4.03+17.6+3.27 = 24.9 MeV, Ech = 4.03+3.5+0.82 = 8.35 MeV.

For calculating the power of a reactor (in which the reaction rate is determined by the D-D step), we count the 2
1
D
-2
1
D
fusion energy per D-D reaction as Efus = (4.03 MeV + 17.6 MeV)×50% + (3.27 MeV)×50% = 12.5 MeV and the energy in charged particles as Ech = (4.03 MeV + 3.5 MeV)×50% + (0.82 MeV)×50% = 4.2 MeV. (Note: if the tritium ion reacts with a deuteron while it still has a large kinetic energy, then the kinetic energy of the helium-4 produced may be quite different from 3.5 MeV,[32] so this calculation of energy in charged particles is only an approximation of the average.) The amount of energy per deuteron consumed is 2/5 of this, or 5.0 MeV (a specific energy of about 225 million MJ per kilogram of deuterium).

Another unique aspect of the 2
1
D
-2
1
D
reaction is that there is only one reactant, which must be taken into account when calculating the reaction rate.

With this choice, we tabulate parameters for four of the most important reactions

fuelZEfus [MeV]Ech [MeV]neutronicity
2
1
D
-3
1
T
117.63.50.80
2
1
D
-2
1
D
112.54.20.66
2
1
D
-3
2
He
218.318.3≈0.05
p+-11
5
B
58.78.7≈0.001

The last column is the neutronicity of the reaction, the fraction of the fusion energy released as neutrons. This is an important indicator of the magnitude of the problems associated with neutrons like radiation damage, biological shielding, remote handling, and safety. For the first two reactions it is calculated as (Efus-Ech)/Efus. For the last two reactions, where this calculation would give zero, the values quoted are rough estimates based on side reactions that produce neutrons in a plasma in thermal equilibrium.

Of course, the reactants should also be mixed in the optimal proportions. This is the case when each reactant ion plus its associated electrons accounts for half the pressure. Assuming that the total pressure is fixed, this means that particle density of the non-hydrogenic ion is smaller than that of the hydrogenic ion by a factor 2/(Z+1). Therefore, the rate for these reactions is reduced by the same factor, on top of any differences in the values of <σv>/T2. On the other hand, because the 2
1
D
-2
1
D
reaction has only one reactant, its rate is twice as high as when the fuel is divided between two different hydrogenic species, thus creating a more efficient reaction.

Thus there is a "penalty" of (2/(Z+1)) for non-hydrogenic fuels arising from the fact that they require more electrons, which take up pressure without participating in the fusion reaction. (It is usually a good assumption that the electron temperature will be nearly equal to the ion temperature. Some authors, however discuss the possibility that the electrons could be maintained substantially colder than the ions. In such a case, known as a "hot ion mode", the "penalty" would not apply.) There is at the same time a "bonus" of a factor 2 for 2
1
D
-2
1
D
because each ion can react with any of the other ions, not just a fraction of them.

We can now compare these reactions in the following table.

fuel<σv>/T2penalty/bonusinverse reactivityLawson criterionpower density (W/m3/kPa2)inverse ratio of power density
2
1
D
-3
1
T
1.24×10−24111341
2
1
D
-2
1
D
1.28×10−26248300.568
2
1
D
-3
2
He
2.24×10−262/383160.4380
p+-6
3
Li
1.46×10−271/217000.0056800
p+-11
5
B
3.01×10−271/312405000.0142500

The maximum value of <σv>/T2 is taken from a previous table. The "penalty/bonus" factor is that related to a non-hydrogenic reactant or a single-species reaction. The values in the column "inverse reactivity" are found by dividing 1.24×1024 by the product of the second and third columns. It indicates the factor by which the other reactions occur more slowly than the 2
1
D
-3
1
T
reaction under comparable conditions. The column "Lawson criterion" weights these results with Ech and gives an indication of how much more difficult it is to achieve ignition with these reactions, relative to the difficulty for the 2
1
D
-3
1
T
reaction. The next-to-last column is labeled "power density" and weights the practical reactivity by Efus. The final column indicates how much lower the fusion power density of the other reactions is compared to the 2
1
D
-3
1
T
reaction and can be considered a measure of the economic potential.

Bremsstrahlung losses in quasineutral, isotropic plasmas

The ions undergoing fusion in many systems will essentially never occur alone but will be mixed with electrons that in aggregate neutralize the ions' bulk electrical charge and form a plasma. The electrons will generally have a temperature comparable to or greater than that of the ions, so they will collide with the ions and emit x-ray radiation of 10–30 keV energy, a process known as Bremsstrahlung.

The huge size of the Sun and stars means that the x-rays produced in this process will not escape and will deposit their energy back into the plasma. They are said to be opaque to x-rays. But any terrestrial fusion reactor will be optically thin for x-rays of this energy range. X-rays are difficult to reflect but they are effectively absorbed (and converted into heat) in less than mm thickness of stainless steel (which is part of a reactor's shield). This means the bremsstrahlung process is carrying energy out of the plasma, cooling it.

The ratio of fusion power produced to x-ray radiation lost to walls is an important figure of merit. This ratio is generally maximized at a much higher temperature than that which maximizes the power density (see the previous subsection). The following table shows estimates of the optimum temperature and the power ratio at that temperature for several reactions:

fuelTi (keV)Pfusion/PBremsstrahlung
2
1
D
-3
1
T
50140
2
1
D
-2
1
D
5002.9
2
1
D
-3
2
He
1005.3
3
2
He
-3
2
He
10000.72
p+-6
3
Li
8000.21
p+-11
5
B
3000.57

The actual ratios of fusion to Bremsstrahlung power will likely be significantly lower for several reasons. For one, the calculation assumes that the energy of the fusion products is transmitted completely to the fuel ions, which then lose energy to the electrons by collisions, which in turn lose energy by Bremsstrahlung. However, because the fusion products move much faster than the fuel ions, they will give up a significant fraction of their energy directly to the electrons. Secondly, the ions in the plasma are assumed to be purely fuel ions. In practice, there will be a significant proportion of impurity ions, which will then lower the ratio. In particular, the fusion products themselves must remain in the plasma until they have given up their energy, and will remain some time after that in any proposed confinement scheme. Finally, all channels of energy loss other than Bremsstrahlung have been neglected. The last two factors are related. On theoretical and experimental grounds, particle and energy confinement seem to be closely related. In a confinement scheme that does a good job of retaining energy, fusion products will build up. If the fusion products are efficiently ejected, then energy confinement will be poor, too.

The temperatures maximizing the fusion power compared to the Bremsstrahlung are in every case higher than the temperature that maximizes the power density and minimizes the required value of the fusion triple product. This will not change the optimum operating point for 2
1
D
-3
1
T
very much because the Bremsstrahlung fraction is low, but it will push the other fuels into regimes where the power density relative to 2
1
D
-3
1
T
is even lower and the required confinement even more difficult to achieve. For 2
1
D
-2
1
D
and 2
1
D
-3
2
He
, Bremsstrahlung losses will be a serious, possibly prohibitive problem. For 3
2
He
-3
2
He
, p+-6
3
Li
and p+-11
5
B
the Bremsstrahlung losses appear to make a fusion reactor using these fuels with a quasineutral, isotropic plasma impossible. Some ways out of this dilemma are considered—and rejected—in fundamental limitations on plasma fusion systems not in thermodynamic equilibrium.[33][34] This limitation does not apply to non-neutral and anisotropic plasmas; however, these have their own challenges to contend with.

Mathematical description of cross section

Fusion under classical physics

In a classical picture, nuclei can be understood as hard spheres that repel each other through the Coulomb force but fuse once the two spheres come close enough for contact. Estimating the radius of an atomic nuclei as about one femtometer, the energy needed for fusion of two hydrogen is:

This would imply that for the core of the sun, which has a Boltzmann distribution with a temperature of around 1.4 keV, the probability hydrogen would reach the threshold is , that is, fusion would never occur. However, fusion in the sun does occur due to quantum mechanics.

Parameterization of cross section

The probability that fusion occurs is greatly increased compared to the classical picture, thanks to the smearing of the effective radius as the DeBroglie wavelength as well as quantum tunnelling through the potential barrier. To determine the rate of fusion reactions, the value of most interest is the cross section, which describes the probability that particle will fuse by giving a characteristic area of interaction. An estimation of the fusion cross sectional area is often broken into three pieces:

Where is the geometric cross section, T is the barrier transparency and R is the reaction characteristics of the reaction.

is of the order of the square of the de-Broglie wavelength where is the reduced mass of the system and is the center of mass energy of the system.

T can be approximated by the Gamow transparency, which has the form: where is the Gamow factor and comes from estimating the quantum tunneling probability through the potential barrier.

R contains all the nuclear physics of the specific reaction and takes very different values depending on the nature of the interaction. However, for most reactions, the variation of is small compared to the variation from the Gamow factor and so is approximated by a function called the Astrophysical S-factor, , which is weakly varying in energy. Putting these dependencies together, one approximation for the fusion cross section as a function of energy takes the form:

More detailed forms of the cross section can be derived through nuclear physics based models and R-matrix theory.

Formulas of fusion cross sections

The Naval Research Lab's plasma physics formulary[35] gives the total cross section in barns as a function of the energy (in keV) of the incident particle towards a target ion at rest fit by the formula:

with the following coefficient values:

NRL Formulary Cross Section Coefficients
DT(1) DD(2i) DD(2ii) DHe3(3) TT(4) THe3(6)
A1 45.95 46.097 47.88 89.27 38.39 123.1
A2 50200 372 482 25900 448 11250
A3 1.368e-2 4.36e-4 3.08e-4 3.98e-3 1.02e-3 0
A4 1.076 1.22 1.177 1.297 2.09 0
A5 409 0 0 647 0 0

Bosch-Hale[36] also reports a R-matrix calculated cross sections fitting observation data with Padé rational approximating coefficients. With energy in units of keV and cross sections in units of millibarn, the factor has the form:

, with the coefficient values:

Bosch-Hale coefficients for the fusion cross section
DT(1) DD(2ii) DHe3(3) THe4
31.3970 68.7508 31.3970 34.3827
A1 5.5576e4 5.7501e6 5.3701e4 6.927e4
A2 2.1054e2 2.5226e3 3.3027e2 7.454e8
A3 -3.2638e-2 4.5566e1 -1.2706e-1 2.050e6
A4 1.4987e-6 0 2.9327e-5 5.2002e4
A5 1.8181e-10 0 -2.5151e-9 0
B1 0 -3.1995e-3 0 6.38e1
B2 0 -8.5530e-6 0 -9.95e-1
B3 0 5.9014e-8 0 6.981e-5
B4 0 0 0 1.728e-4
Applicable Energy Range [keV] 0.5-5000 0.3-900 0.5-4900 0.5-550
2.0 2.2 2.5 1.9

Maxwell averaged nuclear cross sections

In fusions systems that are in thermal equilibrium the particles are in a Maxwell–Boltzmann distribution, meaning the particles have a range of energies centered around the plasma temperature. The sun, magnetically confined plasmas and inertial confinement fusion systems are well modeled to be in a thermal equilibrium. In these cases, the value of interest is the fusion cross section averaged across the Maxwell-Boltzmann distribution. The Naval Research Lab's plasma physics formulary tabulates Maxwell averaged fusion cross sections reactivities in .

NRL Formulary fusion reaction rates averaged over Maxwellian distributions
Temperature [keV] DT(1) DD(2ii) DHe3(3) TT(4) THe3(6)
1 5.5e-21 1.5e-22 1.0e-26 3.3e-22 1.0e-28
2 2.6e-19 5.4e-21 1.4e-23 7.1e-21 1.0e-25
5 1.3e-17 1.8e-19 6.7e-21 1.4e-19 2.1e-22
10 1.1e-16 1.2e-18 2.3e-19 7.2e-19 1.2e-20
20 4.2e-16 5.2e-18 3.8e-18 2.5e-18 2.6e-19
50 8.7e-16 2.1e-17 5.4e-17 8.7e-18 5.3e-18
100 8.5e-16 4.5e-17 1.6e-16 1.9e-17 2.7e-17
200 6.3e-16 8.8e-17 2.4e-16 4.2e-17 9.2e-17
500 3.7e-16 1.8e-16 2.3e-16 8.4e-17 2.9e-16
1000 2.7e-16 2.2e-16 1.8e-16 8.0e-17 5.2e-16

For energies the data can be represented by:


with in units of .

See also

Journals

  • Fusion Engineering and Design
  • Fusion Science and Technology

References

  1. Shultis, J.K. & Faw, R.E. (2002). Fundamentals of nuclear science and engineering. CRC Press. p. 151. ISBN 978-0-8247-0834-4.
  2. Physics Flexbook Archived 28 December 2011 at the Wayback Machine. Ck12.org. Retrieved on 2012-12-19.
  3. Bethe, Hans A. (April 1950). "The Hydrogen Bomb". Bulletin of the Atomic Scientists. 6 (4): 99–104, 125–. Bibcode:1950BuAtS...6d..99B. doi:10.1080/00963402.1950.11461231.
  4. "Progress in Fusion". ITER. Retrieved 15 February 2010.
  5. "ITER – the way to new energy". ITER. 2014. Archived from the original on 22 September 2012.
  6. Boyle, Alan (16 December 2019). "General Fusion gets a $65M boost for fusion power plant from investors — including Jeff Bezos". GeekWire.
  7. Moses, E. I. (2009). "The National Ignition Facility: Ushering in a new age for high energy density science". Physics of Plasmas. 16 (4): 041006. Bibcode:2009PhPl...16d1006M. doi:10.1063/1.3116505.
  8. Kramer, David (March 2011). "DOE looks again at inertial fusion as potential clean-energy source". Physics Today. 64 (3): 26–28. Bibcode:2011PhT....64c..26K. doi:10.1063/1.3563814.
  9. Eddington, A. S. (October 1920). "The Internal Constitution of the Stars". The Scientific Monthly. 11 (4): 297–303. doi:10.1126/science.52.1341.233. JSTOR 6491. PMID 17747682.
  10. Eddington, A. S. (1916). "On the radiative equilibrium of the stars". Monthly Notices of the Royal Astronomical Society. 77: 16–35. Bibcode:1916MNRAS..77...16E. doi:10.1093/mnras/77.1.16.
  11. The Most Tightly Bound Nuclei. Hyperphysics.phy-astr.gsu.edu. Retrieved on 2011-08-17.
  12. What Is The Lawson Criteria, Or How to Make Fusion Power Viable
  13. "Fusor Forums • Index page". Fusor.net. Retrieved 24 August 2014.
  14. "Build a Nuclear Fusion Reactor? No Problem". Clhsonline.net. 23 March 2012. Archived from the original on 30 October 2014. Retrieved 24 August 2014.
  15. Danzico, Matthew (23 June 2010). "Extreme DIY: Building a homemade nuclear reactor in NYC". Retrieved 30 October 2014.
  16. Schechner, Sam (18 August 2008). "Nuclear Ambitions: Amateur Scientists Get a Reaction From Fusion – WSJ". Online.wsj.com. Retrieved 24 August 2014.
  17. Park J, Nebel RA, Stange S, Murali SK (2005). "Experimental Observation of a Periodically Oscillating Plasma Sphere in a Gridded Inertial Electrostatic Confinement Device". Phys Rev Lett. 95 (1): 015003. Bibcode:2005PhRvL..95a5003P. doi:10.1103/PhysRevLett.95.015003. PMID 16090625.
  18. "The Multiple Ambipolar Recirculating Beam Line Experiment" Poster presentation, 2011 US-Japan IEC conference, Dr. Alex Klein
  19. J. Slough, G. Votroubek, and C. Pihl, "Creation of a high-temperature plasma through merging and compression of supersonic field reversed configuration plasmoids" Nucl. Fusion 51,053008 (2011).
  20. A. Asle Zaeem et al "Aneutronic Fusion in Collision of Oppositely Directed Plasmoids" Plasma Physics Reports, Vol. 44, No. 3, pp. 378–386 (2018).
  21. Jones, S.E. (1986). "Muon-Catalysed Fusion Revisited". Nature. 321 (6066): 127–133. Bibcode:1986Natur.321..127J. doi:10.1038/321127a0.
  22. Supplementary methods for "Observation of nuclear fusion driven by a pyroelectric crystal". Main article Naranjo, B.; Gimzewski, J.K.; Putterman, S. (2005). "Observation of nuclear fusion driven by a pyroelectric crystal". Nature. 434 (7037): 1115–1117. Bibcode:2005Natur.434.1115N. doi:10.1038/nature03575. PMID 15858570.
  23. UCLA Crystal Fusion. Rodan.physics.ucla.edu. Retrieved on 2011-08-17. Archived 8 June 2015 at the Wayback Machine
  24. Schewe, Phil & Stein, Ben (2005). "Pyrofusion: A Room-Temperature, Palm-Sized Nuclear Fusion Device". Physics News Update. 729 (1). Archived from the original on 12 November 2013.
  25. Coming in out of the cold: nuclear fusion, for real. Christiansciencemonitor.com (2005-06-06). Retrieved on 2011-08-17.
  26. Nuclear fusion on the desktop ... really!. MSNBC (2005-04-27). Retrieved on 2011-08-17.
  27. Gerstner, E. (2009). "Nuclear energy: The hybrid returns". Nature. 460 (7251): 25–8. doi:10.1038/460025a. PMID 19571861.
  28. Maugh II, Thomas. "Physicist is found guilty of misconduct". Los Angeles Times. Retrieved 17 April 2019.
  29. FusEdWeb | Fusion Education. Fusedweb.pppl.gov (1998-11-09). Retrieved on 2011-08-17. Archived 24 October 2007 at the Wayback Machine
  30. M. Kikuchi, K. Lackner & M. Q. Tran (2012). Fusion Physics. International Atomic Energy Agency. p. 22. ISBN 9789201304100.
  31. Subsection 4.7.4c Archived 16 August 2018 at the Wayback Machine. Kayelaby.npl.co.uk. Retrieved on 2012-12-19.
  32. A momentum and energy balance shows that if the tritium has an energy of ET (and using relative masses of 1, 3, and 4 for the neutron, tritium, and helium) then the energy of the helium can be anything from [(12ET)1/2−(5×17.6MeV+2×ET)1/2]2/25 to [(12ET)1/2+(5×17.6MeV+2×ET)1/2]2/25. For ET=1.01 MeV this gives a range from 1.44 MeV to 6.73 MeV.
  33. Rider, Todd Harrison (1995). "Fundamental Limitations on Plasma Fusion Systems not in Thermodynamic Equilibrium". Dissertation Abstracts International. 56-07 (Section B): 3820. Bibcode:1995PhDT........45R.
  34. Rostoker, Norman; Binderbauer, Michl and Qerushi, Artan. Fundamental limitations on plasma fusion systems not in thermodynamic equilibrium. fusion.ps.uci.edu
  35. Huba, J. (2003). "NRL PLASMA FORMULARY" (PDF). MIT Catalog. Retrieved 11 November 2018.
  36. Bosch, H. S (1993). "Improved formulas for fusion cross-sections and thermal reactivities". Nuclear Fusion. 32 (4): 611–631. doi:10.1088/0029-5515/32/4/I07.

Further reading

Organizations
This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.