Enthalpy

Enthalpy /ˈɛnθəlpi/ (listen), a property of a thermodynamic system, is the sum of the system's internal energy and the product of its pressure and volume.[1][2] In a system contained so as to prevent mass transfer, for processes at constant pressure, the heat absorbed or released equals the change in enthalpy.

The unit of measurement for enthalpy in the International System of Units (SI) is the joule. Other historical conventional units still in use include the British thermal unit (BTU) and the calorie.

Enthalpy comprises a system's internal energy, which is the energy required to create the system, plus the amount of work required to make room for it by displacing its environment and establishing its volume and pressure.[3]

Enthalpy is a state function that depends only on the prevailing equilibrium state identified by the system's internal energy, pressure, and volume. It is an extensive quantity.

Change in enthalpy ( $Δ H$ ) is the preferred expression of system energy change in many chemical, biological, and physical measurements at constant pressure, because it simplifies the description of energy transfer. In a system enclosed so as to prevent matter transfer, at constant pressure, the enthalpy change equals the energy transferred from the environment through heat transfer or work other than expansion work.

The total enthalpy, $H$ , of a system cannot be measured directly. The same situation exists in classical mechanics: only a change or difference in energy carries physical meaning. Enthalpy itself is a thermodynamic potential, so in order to measure the enthalpy of a system, we must refer to a defined reference point; therefore what we measure is the change in enthalpy, $Δ H$ . The $Δ H$ is a positive change in endothermic reactions, and negative in heat-releasing exothermic processes.

For processes under constant pressure, $Δ H$ is equal to the change in the internal energy of the system, plus the pressure-volume work $p Δ V$ done by the system on its surroundings (which is positive for an expansion and negative for a contraction).[4] This means that the change in enthalpy under such conditions is the heat absorbed or released by the system through a chemical reaction or by external heat transfer. Enthalpies for chemical substances at constant pressure usually refer to standard state: most commonly 1 bar (100 kPa) pressure. Standard state does not, strictly speaking, specify a temperature (see standard state), but expressions for enthalpy generally reference the standard heat of formation at 25 °C (298 K).

The enthalpy of an ideal gas is a function of temperature only, so does not depend on pressure. Real materials at common temperatures and pressures usually closely approximate this behavior, which greatly simplifies enthalpy calculation and use in practical designs and analyses.

History

The word enthalpy was coined relatively late, in the early 20th century, in analogy with the 19th-century terms energy (introduced in its modern sense by Thomas Young in 1802) and entropy (coined in analogy to energy by Rudolf Clausius in 1865). Where energy uses the root of the Greek word ἔργον (ergon) "work" to express the idea of "work-content" and where entropy uses the Greek word τροπή (tropē) "transformation" to express the idea of "transformation-content", so by analogy, enthalpy uses the root of the Greek word θάλπος (thalpos) "warmth, heat"[5] to express the idea of "heat-content". The term does in fact stand in for the older term "heat content",[6] a term which is now mostly deprecated as misleading, as $dH$ refers to the amount of heat absorbed in a process at constant pressure only,[7] but not in the general case (when pressure is variable).[8] Josiah Willard Gibbs used the term "a heat function for constant pressure" for clarity.[note 1]

Introduction of the concept of "heat content" $H$ is associated with Benoît Paul Émile Clapeyron and Rudolf Clausius (Clausius–Clapeyron relation, 1850).

The term enthalpy first appeared in print in 1909.[9] It is attributed to Heike Kamerlingh Onnes, who most likely introduced it orally the year before, at the first meeting of the Institute of Refrigeration in Paris.[10] It gained currency only in the 1920s, notably with the Mollier Steam Tables and Diagrams, published in 1927.

Until the 1920s, the symbol $H$ was used, somewhat inconsistently, for "heat" in general. The definition of $H$ as strictly limited to enthalpy or "heat content at constant pressure" was formally proposed by Alfred W. Porter in 1922.[11][12]

Formal definition

The enthalpy of a thermodynamic system is defined as[13][14]

H = U + pV

,

where

H

is enthalpy,

U

is the internal energy of the system,

p

is pressure,

V

is the volume of the system.

Enthalpy is an extensive property. This means that, for homogeneous systems, the enthalpy is proportional to the size of the system. It is convenient to introduce the specific enthalpy $h = H / m$ , where $m$ is the mass of the system, or the molar enthalpy $H m = H / n$ , where $n$ is the number of moles ( $h$ and $H m$ are intensive properties). For inhomogeneous systems the enthalpy is the sum of the enthalpies of the composing subsystems:

H=\sum _{k}H_{k},

where

H

is the total enthalpy of all the subsystems,

k

refers to the various subsystems,

H k

refers to the enthalpy of each subsystem.

A closed system may lie in thermodynamic equilibrium in a static gravitational field, so that its pressure $p$ varies continuously with altitude, while, because of the equilibrium requirement, its temperature $T$ is invariant with altitude. (Correspondingly, the system's gravitational potential energy density also varies with altitude.) Then the enthalpy summation becomes an integral:

H=\int (\rho h)\,dV,

where

ρ

("rho") is density (mass per unit volume),

h

is the specific enthalpy (enthalpy per unit mass),

(ρh)

represents the enthalpy density (enthalpy per unit volume),

dV

denotes an infinitesimally small element of volume within the system, for example, the volume of an infinitesimally thin horizontal layer,

the integral therefore represents the sum of the enthalpies of all the elements of the volume.

The enthalpy of a closed homogeneous system is its cardinal energy function $H (S, p)$ , with natural state variables its entropy $S [p]$ and its pressure $p$ . A differential relation for it can be derived as follows. We start from the first law of thermodynamics for closed systems for an infinitesimal process:

dU=\delta Q-\delta W,

where

Δ Q

is a small amount of heat added to the system,

Δ W

a small amount of work performed by the system.

In a homogeneous system in which only reversible, or quasi-static, processes are considered, the second law of thermodynamics gives $Δ Q = T dS$ , with $T$ the absolute temperature and $dS$ the infinitesimal change in entropy $S$ of the system. Furthermore, if only $pV$ work is done, $Δ W = p dV$ . As a result,

dU=T\,dS-p\,dV.

Adding $d (pV)$ to both sides of this expression gives

dU+d(pV)=T\,dS-p\,dV+d(pV),

or

d(U+pV)=T\,dS+V\,dp.

So

dH(S,p)=T\,dS+V\,dp.

Other expressions

The above expression of $dH$ in terms of entropy and pressure may be unfamiliar to some readers. However, there are expressions in terms of more familiar variables such as temperature and pressure:[13]^:88[15]

dH=C_{p}\,dT+V(1-\alpha T)\,dp.

Here $C p$ is the heat capacity at constant pressure and $α$ is the coefficient of (cubic) thermal expansion:

\alpha ={\frac {1}{V}}\left({\frac {\partial V}{\partial T}}\right)_{p}.

With this expression one can, in principle, determine the enthalpy if $C p$ and $V$ are known as functions of $p$ and $T$ .

Note that for an ideal gas, $αT = 1$ ,[note 2] so that

dH=C_{p}\,dT.

In a more general form, the first law describes the internal energy with additional terms involving the chemical potential and the number of particles of various types. The differential statement for $dH$ then becomes

dH=T\,dS+V\,dp+\sum _{i}\mu _{i}\,dN_{i},

where $μ i$ is the chemical potential per particle for an $i$ -type particle, and $N i$ is the number of such particles. The last term can also be written as $μ i dn i$ (with $dn i$ the number of moles of component $i$ added to the system and, in this case, $μ i$ the molar chemical potential) or as $μ i dm i$ (with $dm i$ the mass of component $i$ added to the system and, in this case, $μ i$ the specific chemical potential).

Cardinal functions

The enthalpy, $H (S [p], p,{N i})$ , expresses the thermodynamics of a system in the energy representation. As a function of state, its arguments include both one intensive and several extensive state variables. The state variables $S [p]$ , $p$ , and ${N i}$ are said to be the natural state variables in this representation. They are suitable for describing processes in which they are experimentally controlled. For example, in an idealized process, $S [p]$ and $p$ can be controlled by preventing heat and matter transfer by enclosing the system with a wall that is adiathermal and impermeable to matter, and by making the process infinitely slow, and by varying only the external pressure on the piston that controls the volume of the system. This is the basis of the so-called adiabatic approximation that is used in meteorology.[16]

Alongside the enthalpy, with these arguments, the other cardinal function of state of a thermodynamic system is its entropy, as a function, $S [p](H, p,{N i})$ , of the same list of variables of state, except that the entropy, $S [p]$ , is replaced in the list by the enthalpy, $H$ . It expresses the entropy representation. The state variables $H$ , $p$ , and ${N i}$ are said to be the natural state variables in this representation. They are suitable for describing processes in which they are experimentally controlled. For example, $H$ and $p$ can be controlled by allowing heat transfer, and by varying only the external pressure on the piston that sets the volume of the system.[17][18][19]

Physical interpretation

The $U$ term can be interpreted as the energy required to create the system, and the $pV$ term as the work that would be required to "make room" for the system if the pressure of the environment remained constant. When a system, for example, $n$ moles of a gas of volume $V$ at pressure $p$ and temperature $T$ , is created or brought to its present state from absolute zero, energy must be supplied equal to its internal energy $U$ plus $pV$ , where $pV$ is the work done in pushing against the ambient (atmospheric) pressure.

In basic physics and statistical mechanics it may be more interesting to study the internal properties of the system and therefore the internal energy is used.[20][21] In basic chemistry, experiments are often conducted at constant atmospheric pressure, and the pressure-volume work represents an energy exchange with the atmosphere that cannot be accessed or controlled, so that $Δ H$ is the expression chosen for the heat of reaction.

For a heat engine a change in its internal energy is the difference between the heat input and the pressure-volume work done by the working substance while a change in its enthalpy is the difference between the heat input and the work done by the engine:[22]

dH=\delta Q-\delta W

where the work $W$ done by the engine is:

W=-\oint pdV

Relationship to heat

In order to discuss the relation between the enthalpy increase and heat supply, we return to the first law for closed systems, with the physics sign convention: $dU = δQ - δW$ , where the heat $δQ$ is supplied by conduction, radiation, and Joule heating. We apply it to the special case with a constant pressure at the surface. In this case the work term can be split into two contributions, the so-called $pV$ work, given by $p dV$ (where here $p$ is the pressure at the surface, $dV$ is the increase of the volume of the system), and the so-called isochoric mechanical work $δW'$ , such as stirring by a shaft with paddles or by an externally driven magnetic field acting on an internal rotor. Cases of long range electromagnetic interaction require further state variables in their formulation, and are not considered here. So we write $δW = p dV + δW'$ . In this case the first law reads:

dU=\delta Q-p\,dV-\delta W'.

Now,

dH=dU+d(pV).

So

dH=\delta Q+V\,dp+p\,dV-p\,dV-\delta W'

\,\,=\delta Q+V\,dp-\delta W'.

With sign convention of physics, $δW' < 0$ , because isochoric shaft work done by an external device on the system adds energy to the system, and may be viewed as virtually adding heat. The only thermodynamic mechanical work done by the system is expansion work, p dV.[23]

The system is under constant pressure ( $dp = 0$ ). Consequently, the increase in enthalpy of the system is equal to the added heat and virtual heat:

dH=\delta Q-\delta W'.

This is why the now-obsolete term heat content was used in the 19th century.

Applications

In thermodynamics, one can calculate enthalpy by determining the requirements for creating a system from "nothingness"; the mechanical work required, $pV$ , differs based upon the conditions that obtain during the creation of the thermodynamic system.

Energy must be supplied to remove particles from the surroundings to make space for the creation of the system, assuming that the pressure $p$ remains constant; this is the $pV$ term. The supplied energy must also provide the change in internal energy, $U$ , which includes activation energies, ionization energies, mixing energies, vaporization energies, chemical bond energies, and so forth. Together, these constitute the change in the enthalpy $U + pV$ . For systems at constant pressure, with no external work done other than the $pV$ work, the change in enthalpy is the heat received by the system.

For a simple system, with a constant number of particles, the difference in enthalpy is the maximum amount of thermal energy derivable from a thermodynamic process in which the pressure is held constant.[24]

Heat of reaction

The total enthalpy of a system cannot be measured directly; the enthalpy change of a system is measured instead. Enthalpy change is defined by the following equation:

\Delta H=H_{\mathrm {f} }-H_{\mathrm {i} },

where

Δ H

is the "enthalpy change",

H f

is the final enthalpy of the system (in a chemical reaction, the enthalpy of the products),

H i

is the initial enthalpy of the system (in a chemical reaction, the enthalpy of the reactants).

For an exothermic reaction at constant pressure, the system's change in enthalpy equals the energy released in the reaction, including the energy retained in the system and lost through expansion against its surroundings. In a similar manner, for an endothermic reaction, the system's change in enthalpy is equal to the energy absorbed in the reaction, including the energy lost by the system and gained from compression from its surroundings. If $Δ H$ is positive, the reaction is endothermic, that is heat is absorbed by the system due to the products of the reaction having a greater enthalpy than the reactants. On the other hand, if $Δ H$ is negative, the reaction is exothermic, that is the overall decrease in enthalpy is achieved by the generation of heat.[25]

From the definition of enthalpy as $H = U + pV$ , the enthalpy change at constant pressure $Δ H = Δ U + p Δ V$ . However for most chemical reactions, the work term $p Δ V$ is much smaller than the internal energy change $Δ U$ which is approximately equal to $Δ H$ . As an example, for the combustion of carbon monoxide 2 CO(g) + O₂(g) → 2 CO₂(g), $Δ H$ = −566.0 kJ and $Δ U$ = −563.5 kJ.[26] Since the differences are so small, reaction enthalpies are often loosely described as reaction energies and analyzed in terms of bond energies.

Specific enthalpy

The specific enthalpy of a uniform system is defined as $h = H / m$ where $m$ is the mass of the system. The SI unit for specific enthalpy is joule per kilogram. It can be expressed in other specific quantities by $h = u + pv$ , where $u$ is the specific internal energy, $p$ is the pressure, and $v$ is specific volume, which is equal to $1 / ρ$ , where $ρ$ is the density.

Enthalpy changes

An enthalpy change describes the change in enthalpy observed in the constituents of a thermodynamic system when undergoing a transformation or chemical reaction. It is the difference between the enthalpy after the process has completed, i.e. the enthalpy of the products, and the initial enthalpy of the system, namely the reactants. These processes are reversible and the enthalpy for the reverse process is the negative value of the forward change.

A common standard enthalpy change is the enthalpy of formation, which has been determined for a large number of substances. Enthalpy changes are routinely measured and compiled in chemical and physical reference works, such as the CRC Handbook of Chemistry and Physics. The following is a selection of enthalpy changes commonly recognized in thermodynamics.

When used in these recognized terms the qualifier change is usually dropped and the property is simply termed enthalpy of 'process'. Since these properties are often used as reference values it is very common to quote them for a standardized set of environmental parameters, or standard conditions, including:

A temperature of 25 °C or 298.15 K,
A pressure of one atmosphere (1 atm or 101.325 kPa),
A concentration of 1.0 M when the element or compound is present in solution,
Elements or compounds in their normal physical states, i.e. standard state.

For such standardized values the name of the enthalpy is commonly prefixed with the term standard, e.g. standard enthalpy of formation.

Chemical properties:

Enthalpy of reaction, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of substance reacts completely.
Enthalpy of formation, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of a compound is formed from its elementary antecedents.
Enthalpy of combustion, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of a substance burns completely with oxygen.
Enthalpy of hydrogenation, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of an unsaturated compound reacts completely with an excess of hydrogen to form a saturated compound.
Enthalpy of atomization, defined as the enthalpy change required to atomize one mole of compound completely.
Enthalpy of neutralization, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of water is formed when an acid and a base react.
Standard Enthalpy of solution, defined as the enthalpy change observed in a constituent of a thermodynamic system when one mole of a solute is dissolved completely in an excess of solvent, so that the solution is at infinite dilution.
Standard enthalpy of Denaturation (biochemistry), defined as the enthalpy change required to denature one mole of compound.
Enthalpy of hydration, defined as the enthalpy change observed when one mole of gaseous ions are completely dissolved in water forming one mole of aqueous ions.

Physical properties:

Enthalpy of fusion, defined as the enthalpy change required to completely change the state of one mole of substance between solid and liquid states.
Enthalpy of vaporization, defined as the enthalpy change required to completely change the state of one mole of substance between liquid and gaseous states.
Enthalpy of sublimation, defined as the enthalpy change required to completely change the state of one mole of substance between solid and gaseous states.
Lattice enthalpy, defined as the energy required to separate one mole of an ionic compound into separated gaseous ions to an infinite distance apart (meaning no force of attraction).
Enthalpy of mixing, defined as the enthalpy change upon mixing of two (non-reacting) chemical substances.

Open systems

In thermodynamic open systems, mass (of substances) may flow in and out of the system boundaries. The first law of thermodynamics for open systems states: The increase in the internal energy of a system is equal to the amount of energy added to the system by mass flowing in and by heating, minus the amount lost by mass flowing out and in the form of work done by the system:

dU=\delta Q+dU_{\text{in}}-dU_{\text{out}}-\delta W,

where $U in$ is the average internal energy entering the system, and $U out$ is the average internal energy leaving the system.

During steady, continuous operation, an energy balance applied to an open system equates shaft work performed by the system to heat added plus net enthalpy added

The region of space enclosed by the boundaries of the open system is usually called a control volume, and it may or may not correspond to physical walls. If we choose the shape of the control volume such that all flow in or out occurs perpendicular to its surface, then the flow of mass into the system performs work as if it were a piston of fluid pushing mass into the system, and the system performs work on the flow of mass out as if it were driving a piston of fluid. There are then two types of work performed: flow work described above, which is performed on the fluid (this is also often called $pV$ work), and shaft work, which may be performed on some mechanical device.

These two types of work are expressed in the equation

\delta W=d(p_{\text{out}}V_{\text{out}})-d(p_{\text{in}}V_{\text{in}})+\delta W_{\text{shaft}}.

Substitution into the equation above for the control volume (cv) yields:

dU_{\text{cv}}=\delta Q+dU_{\text{in}}+d(p_{\text{in}}V_{\text{in}})-dU_{\text{out}}-d(p_{\text{out}}V_{\text{out}})-\delta W_{\text{shaft}}.

The definition of enthalpy, $H$ , permits us to use this thermodynamic potential to account for both internal energy and $pV$ work in fluids for open systems:

dU_{\text{cv}}=\delta Q+dH_{\text{in}}-dH_{\text{out}}-\delta W_{\text{shaft}}.

If we allow also the system boundary to move (e.g. due to moving pistons), we get a rather general form of the first law for open systems.[27] In terms of time derivatives it reads:

{\frac {dU}{dt}}=\sum _{k}{\dot {Q}}_{k}+\sum _{k}{\dot {H}}_{k}-\sum _{k}p_{k}{\frac {dV_{k}}{dt}}-P,

with sums over the various places $k$ where heat is supplied, mass flows into the system, and boundaries are moving. The $Ḣ k$ terms represent enthalpy flows, which can be written as

{\dot {H}}_{k}=h_{k}{\dot {m}}_{k}=H_{\mathrm {m} }{\dot {n}}_{k},

with $ṁ k$ the mass flow and $ṅ k$ the molar flow at position $k$ respectively. The term $dV k / dt$ represents the rate of change of the system volume at position $k$ that results in $pV$ power done by the system. The parameter P represents all other forms of power done by the system such as shaft power, but it can also be, say, electric power produced by an electrical power plant.

Note that the previous expression holds true only if the kinetic energy flow rate is conserved between system inlet and outlet. Otherwise, it has to be included in the enthalpy balance. During steady-state operation of a device (see turbine, pump, and engine), the average $dU / dt$ may be set equal to zero. This yields a useful expression for the average power generation for these devices in the absence of chemical reactions:

P=\sum _{k}\left\langle {\dot {Q}}_{k}\right\rangle +\sum _{k}\left\langle {\dot {H}}_{k}\right\rangle -\sum _{k}\left\langle p_{k}{\frac {dV_{k}}{dt}}\right\rangle ,

where the angle brackets denote time averages. The technical importance of the enthalpy is directly related to its presence in the first law for open systems, as formulated above.

Diagrams

T - s

diagram of nitrogen.[28] The red curve at the left is the melting curve. The red dome represents the two-phase region with the low-entropy side the saturated liquid and the high-entropy side the saturated gas. The black curves give the

T - s

relation along isobars. The pressures are indicated in bar. The blue curves are isenthalps (curves of constant enthalpy). The values are indicated in blue in kJ/kg. The specific points a, b, etc., are treated in the main text.

The enthalpy values of important substances can be obtained using commercial software. Practically all relevant material properties can be obtained either in tabular or in graphical form. There are many types of diagrams, such as $h - T$ diagrams, which give the specific enthalpy as function of temperature for various pressures, and $h - p$ diagrams, which give $h$ as function of $p$ for various $T$ . One of the most common diagrams is the temperature–specific entropy diagram ( $T - s$ diagram). It gives the melting curve and saturated liquid and vapor values together with isobars and isenthalps. These diagrams are powerful tools in the hands of the thermal engineer.

Some basic applications

The points a through h in the figure play a role in the discussion in this section.

Point	$T$ (K)	$p$ (bar)	$s$ (kJ/(kg K))	$h$ (kJ/kg)
a	300	1	6.85	461
b	380	2	6.85	530
c	300	200	5.16	430
d	270	1	6.79	430
e	108	13	3.55	100
f	77.2	1	3.75	100
g	77.2	1	2.83	28
h	77.2	1	5.41	230

Points e and g are saturated liquids, and point h is a saturated gas.

Throttling

Schematic diagram of a throttling in the steady state. Fluid enters the system (dotted rectangle) at point 1 and leaves it at point 2. The mass flow is

ṁ

.

One of the simple applications of the concept of enthalpy is the so-called throttling process, also known as Joule-Thomson expansion. It concerns a steady adiabatic flow of a fluid through a flow resistance (valve, porous plug, or any other type of flow resistance) as shown in the figure. This process is very important, since it is at the heart of domestic refrigerators, where it is responsible for the temperature drop between ambient temperature and the interior of the refrigerator. It is also the final stage in many types of liquefiers.

For a steady state flow regime, the enthalpy of the system (dotted rectangle) has to be constant. Hence

0={\dot {m}}h_{1}-{\dot {m}}h_{2}.

Since the mass flow is constant, the specific enthalpies at the two sides of the flow resistance are the same:

h_{1}=h_{2},

that is, the enthalpy per unit mass does not change during the throttling. The consequences of this relation can be demonstrated using the $T - s$ diagram above. Point c is at 200 bar and room temperature (300 K). A Joule–Thomson expansion from 200 bar to 1 bar follows a curve of constant enthalpy of roughly 425 kJ/kg (not shown in the diagram) lying between the 400 and 450 kJ/kg isenthalps and ends in point d, which is at a temperature of about 270 K. Hence the expansion from 200 bar to 1 bar cools nitrogen from 300 K to 270 K. In the valve, there is a lot of friction, and a lot of entropy is produced, but still the final temperature is below the starting value.

Point e is chosen so that it is on the saturated liquid line with $h$ = 100 kJ/kg. It corresponds roughly with $p$ = 13 bar and $T$ = 108 K. Throttling from this point to a pressure of 1 bar ends in the two-phase region (point f). This means that a mixture of gas and liquid leaves the throttling valve. Since the enthalpy is an extensive parameter, the enthalpy in f ( $h f$ ) is equal to the enthalpy in g ( $h g$ ) multiplied by the liquid fraction in f ( $x f$ ) plus the enthalpy in h ( $h h$ ) multiplied by the gas fraction in f $(1 - x f)$ . So

h_{\mathbf {f} }=x_{\mathbf {f} }h_{\mathbf {g} }+(1-x_{\mathbf {f} })h_{\mathbf {h} }.

With numbers: $100 = x f \times 28 + (1 - x f) \times 230$ , so $x f$ = 0.64. This means that the mass fraction of the liquid in the liquid–gas mixture that leaves the throttling valve is 64%.

Compressors

Schematic diagram of a compressor in the steady state. Fluid enters the system (dotted rectangle) at point 1 and leaves it at point 2. The mass flow is

ṁ

. A power

P

is applied and a heat flow

Q̇

is released to the surroundings at ambient temperature

T a

.

A power $P$ is applied e.g. as electrical power. If the compression is adiabatic, the gas temperature goes up. In the reversible case it would be at constant entropy, which corresponds with a vertical line in the $T - s$ diagram. For example, compressing nitrogen from 1 bar (point a) to 2 bar (point b) would result in a temperature increase from 300 K to 380 K. In order to let the compressed gas exit at ambient temperature $T a$ , heat exchange, e.g. by cooling water, is necessary. In the ideal case the compression is isothermal. The average heat flow to the surroundings is $Q̇$ . Since the system is in the steady state the first law gives

0=-{\dot {Q}}+{\dot {m}}h_{1}-{\dot {m}}h_{2}+P.

The minimal power needed for the compression is realized if the compression is reversible. In that case the second law of thermodynamics for open systems gives

0=-{\frac {\dot {Q}}{T_{\mathrm {a} }}}+{\dot {m}}s_{1}-{\dot {m}}s_{2}.

Eliminating $Q̇$ gives for the minimal power

{\frac {P_{\text{min}}}{\dot {m}}}=h_{2}-h_{1}-T_{\mathrm {a} }(s_{2}-s_{1}).

For example, compressing 1 kg of nitrogen from 1 bar to 200 bar costs at least $(h c - h a) - T a (s c - s a)$ . With the data, obtained with the $T - s$ diagram, we find a value of (430 − 461) − 300 × (5.16 − 6.85) = 476 kJ/kg.

The relation for the power can be further simplified by writing it as

{\frac {P_{\text{min}}}{\dot {m}}}=\int _{1}^{2}(dh-T_{\mathrm {a} }\,ds).

With $dh = T ds + v dp$ , this results in the final relation

{\frac {P_{\text{min}}}{\dot {m}}}=\int _{1}^{2}v\,dp.

Notes

The Collected Works of J. Willard Gibbs, Vol. I do not contain reference to the word enthalpy, but rather reference the "heat function for constant pressure". See: Henderson, Douglas; Eyring, Henry; Jost, Wilhelm (1967). Physical Chemistry: An Advanced Treatise. Academic Press. p. 29.
$\alpha T={\frac {T}{V}}\left({\frac {\partial ({\frac {nRT}{P}})}{\partial T}}\right)_{p}={\frac {nRT}{PV}}=1$

References

"Oxford Living Dictionaries". Archived from the original on 2016-08-17. Retrieved 2018-02-19.
"IUPAC Gold Book. Enthalpy, H". Retrieved 2018-02-19.
Zemansky, Mark W. (1968). "Chapter 11". Heat and Thermodynamics (5th ed.). New York, NY: McGraw-Hill. p. 275.
Van Wylen, G. J.; Sonntag, R. E. (1985). "Section 5.5". Fundamentals of Classical Thermodynamics (3rd ed.). New York: John Wiley & Sons. ISBN 978-0-471-82933-1.
θάλπος in A Greek–English Lexicon.
Howard (2002) quotes J. R. Partington in An Advanced Treatise on Physical Chemistry (1949) as saying that the function H was "usually called the heat content".
Tinoco, Jr., Ignacio; Sauer, Kenneth; Wang, James C. (1995). Physical Chemistry (3rd ed.). Prentice-Hall. p. 41. ISBN 978-0-13-186545-7.
Laidler, Keith J.; Meiser, John H. (1982). Physical Chemistry. Benjamin/Cummings. p. 53. ISBN 978-0-8053-5682-3.
Dalton, J. P. (1909). "Researches on the Joule-Kelvin-effect, especially at low temperatures. I. Calculations for hydrogen". Proceedings of the Section of Sciences (Koninklijke Akademie van Wetenschappen Te Amsterdam [Royal Academy of Sciences at Amsterdam]). 11 (part 2): 863–873. Bibcode:1908KNAB...11..863D. ; see p. 864, footnote (1).
See:
- Laidler, Keith (1995). The World of Physical Chemistry. Oxford University Press. p. 110.
- Van Ness, Hendrick C. (2003). "H Is for Enthalpy". Journal of Chemical Education. 80 (6): 486. Bibcode:2003JChEd..80..486V. doi:10.1021/ed080p486.1.
Porter, Alfred W. (1922). "The generation and utilisation of cold. A general discussion". Transactions of the Faraday Society. 18: 139–143. doi:10.1039/tf9221800139.; see p. 140.
Howard, Irmgard (2002). "H Is for Enthalpy, Thanks to Heike Kamerlingh Onnes and Alfred W. Porter". Journal of Chemical Education. 79 (6): 697. Bibcode:2002JChEd..79..697H. doi:10.1021/ed079p697.
Guggenheim, E. A. (1959). Thermodynamics. Amsterdam: North-Holland Publishing Company.
Zumdahl, Steven S. (2008). "Thermochemistry". Chemistry. Cengage Learning. p. 243. ISBN 978-0-547-12532-9. Archived from the original on 2013-11-14.
Moran, M. J.; Shapiro, H. N. (2006). Fundamentals of Engineering Thermodynamics (5th ed.). John Wiley & Sons. p. 511.
Iribarne, J.V., Godson, W.L. (1981). Atmospheric Thermodynamics, 2nd edition, Kluwer Academic Publishers, Dordrecht, ISBN 90-277-1297-2, pp. 235–236.
Tschoegl, N.W. (2000). Fundamentals of Equilibrium and Steady-State Thermodynamics, Elsevier, Amsterdam, ISBN 0-444-50426-5, p. 17.
Callen, H. B. (1960/1985), Thermodynamics and an Introduction to Thermostatistics, (first edition 1960), second edition 1985, John Wiley & Sons, New York, ISBN 0-471-86256-8, Chapter 5.
Münster, A. (1970), Classical Thermodynamics, translated by E. S. Halberstadt, Wiley–Interscience, London, ISBN 0-471-62430-6, p. 6.
Reif, F. (1967). Statistical Physics. London: McGraw-Hill.
Kittel, C.; Kroemer, H. (1980). Thermal Physics. London: Freeman.
Bartelmann, Matthias (2015). Theoretische Physik. Springer Spektrum. pp. 1106–1108. ISBN 978-3-642-54617-4.
Ebbing, Darrel; Gammon, Steven (2010). General Chemistry. Cengage Learning. p. 231. ISBN 978-0-538-49752-7. Archived from the original on 2013-11-14.
Rathakrishnan (2015). High Enthalpy Gas Dynamics. John Wiley and Sons Singapore Pte. Ltd. ISBN 978-1118821893.
Laidler, Keith J.; Meiser, John H. (1982). Physical Chemistry. Benjamin/Cummings. p. 53. ISBN 978-0-8053-5682-3.
Petrucci, Ralph H.; Harwood, William S.; Herring, F. Geoffrey (2002). General Chemistry (8th ed.). Prentice Hall. pp. 237–238. ISBN 978-0-13-014329-7.
Moran, M. J.; Shapiro, H. N. (2006). Fundamentals of Engineering Thermodynamics (5th ed.). John Wiley & Sons. p. 129.
Figure composed with data obtained with RefProp, NIST Standard Reference Database 23.

Bibliography

Dalton, J.P. (1909). "Researches on the Joule–Kelvin effect, especially at low temperatures. I. Calculations for hydrogen" (PDF). KNAW Proceedings. 11: 863–873. Bibcode:1908KNAB...11..863D.
Haase, R. (1971). Jost, W. (ed.). Physical Chemistry: An Advanced Treatise. New York: Academic. p. 29.
Gibbs, J. W. The Collected Works of J. Willard Gibbs, Vol. I (1948 ed.). New Haven, CT: Yale University Press. p. 88.
Howard, I. K. (2002). "H Is for Enthalpy, Thanks to Heike Kamerlingh Onnes and Alfred W. Porter". J. Chem. Educ. 79 (6): 697–698. Bibcode:2002JChEd..79..697H. doi:10.1021/ed079p697.
Laidler, K. (1995). The World of Physical Chemistry. Oxford: Oxford University Press. p. 110.
Kittel, C.; Kroemer, H. (1980). Thermal Physics. New York: S. R. Furphy & Co. p. 246.
DeHoff, R. (2006). Thermodynamics in Materials Science. CRC Press. ISBN 9780849340659.

External links

Enthalpy – Eric Weisstein's World of Physics
Enthalpy – Georgia State University
Enthalpy example calculations – Texas A&M University Chemistry Department

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.

[9] The Collected Works of J. Willard Gibbs, Vol. I do not contain reference to the word enthalpy, but rather reference the "heat function for constant pressure". See: Henderson, Douglas; Eyring, Henry; Jost, Wilhelm (1967). Physical Chemistry: An Advanced Treatise. Academic Press. p. 29.

[17] $\alpha T={\frac {T}{V}}\left({\frac {\partial ({\frac {nRT}{P}})}{\partial T}}\right)_{p}={\frac {nRT}{PV}}=1$

[1] "Oxford Living Dictionaries". Archived from the original on 2016-08-17. Retrieved 2018-02-19.

[2] "IUPAC Gold Book. Enthalpy, H". Retrieved 2018-02-19.

[3] Zemansky, Mark W. (1968). "Chapter 11". Heat and Thermodynamics (5th ed.). New York, NY: McGraw-Hill. p. 275.

[4] Van Wylen, G. J.; Sonntag, R. E. (1985). "Section 5.5". Fundamentals of Classical Thermodynamics (3rd ed.). New York: John Wiley & Sons. ISBN 978-0-471-82933-1.

[5] θάλπος in A Greek–English Lexicon.

[6] Howard (2002) quotes J. R. Partington in An Advanced Treatise on Physical Chemistry (1949) as saying that the function H was "usually called the heat content".

[7] Tinoco, Jr., Ignacio; Sauer, Kenneth; Wang, James C. (1995). Physical Chemistry (3rd ed.). Prentice-Hall. p. 41. ISBN 978-0-13-186545-7.

[8] Laidler, Keith J.; Meiser, John H. (1982). Physical Chemistry. Benjamin/Cummings. p. 53. ISBN 978-0-8053-5682-3.

[10] Dalton, J. P. (1909). "Researches on the Joule-Kelvin-effect, especially at low temperatures. I. Calculations for hydrogen". Proceedings of the Section of Sciences (Koninklijke Akademie van Wetenschappen Te Amsterdam [Royal Academy of Sciences at Amsterdam]). 11 (part 2): 863–873. Bibcode:1908KNAB...11..863D. ; see p. 864, footnote (1).

[11] See:
Laidler, Keith (1995). The World of Physical Chemistry. Oxford University Press. p. 110.

Van Ness, Hendrick C. (2003). "H Is for Enthalpy". Journal of Chemical Education. 80 (6): 486. Bibcode:2003JChEd..80..486V. doi:10.1021/ed080p486.1.

[13] Laidler, Keith (1995). The World of Physical Chemistry. Oxford University Press. p. 110.

[14] Van Ness, Hendrick C. (2003). "H Is for Enthalpy". Journal of Chemical Education. 80 (6): 486. Bibcode:2003JChEd..80..486V. doi:10.1021/ed080p486.1.

[12] Porter, Alfred W. (1922). "The generation and utilisation of cold. A general discussion". Transactions of the Faraday Society. 18: 139–143. doi:10.1039/tf9221800139.; see p. 140.

[Howard-13] Howard, Irmgard (2002). "H Is for Enthalpy, Thanks to Heike Kamerlingh Onnes and Alfred W. Porter". Journal of Chemical Education. 79 (6): 697. Bibcode:2002JChEd..79..697H. doi:10.1021/ed079p697.

[Guggenheim-14] Guggenheim, E. A. (1959). Thermodynamics. Amsterdam: North-Holland Publishing Company.

[15] Zumdahl, Steven S. (2008). "Thermochemistry". Chemistry. Cengage Learning. p. 243. ISBN 978-0-547-12532-9. Archived from the original on 2013-11-14.

[16] Moran, M. J.; Shapiro, H. N. (2006). Fundamentals of Engineering Thermodynamics (5th ed.). John Wiley & Sons. p. 511.

[18] Iribarne, J.V., Godson, W.L. (1981). Atmospheric Thermodynamics, 2nd edition, Kluwer Academic Publishers, Dordrecht, ISBN 90-277-1297-2, pp. 235–236.

[19] Tschoegl, N.W. (2000). Fundamentals of Equilibrium and Steady-State Thermodynamics, Elsevier, Amsterdam, ISBN 0-444-50426-5, p. 17.

[20] Callen, H. B. (1960/1985), Thermodynamics and an Introduction to Thermostatistics, (first edition 1960), second edition 1985, John Wiley & Sons, New York, ISBN 0-471-86256-8, Chapter 5.

[21] Münster, A. (1970), Classical Thermodynamics, translated by E. S. Halberstadt, Wiley–Interscience, London, ISBN 0-471-62430-6, p. 6.

[22] Reif, F. (1967). Statistical Physics. London: McGraw-Hill.

[23] Kittel, C.; Kroemer, H. (1980). Thermal Physics. London: Freeman.

[24] Bartelmann, Matthias (2015). Theoretische Physik. Springer Spektrum. pp. 1106–1108. ISBN 978-3-642-54617-4.

[25] Ebbing, Darrel; Gammon, Steven (2010). General Chemistry. Cengage Learning. p. 231. ISBN 978-0-538-49752-7. Archived from the original on 2013-11-14.

[26] Rathakrishnan (2015). High Enthalpy Gas Dynamics. John Wiley and Sons Singapore Pte. Ltd. ISBN 978-1118821893.

[27] Laidler, Keith J.; Meiser, John H. (1982). Physical Chemistry. Benjamin/Cummings. p. 53. ISBN 978-0-8053-5682-3.

[28] Petrucci, Ralph H.; Harwood, William S.; Herring, F. Geoffrey (2002). General Chemistry (8th ed.). Prentice Hall. pp. 237–238. ISBN 978-0-13-014329-7.

[29] Moran, M. J.; Shapiro, H. N. (2006). Fundamentals of Engineering Thermodynamics (5th ed.). John Wiley & Sons. p. 129.

[30] Figure composed with data obtained with RefProp, NIST Standard Reference Database 23.

Heating, ventilation, and air conditioning
Fundamental concepts	Air changes per hour Bake-out Building envelope Convection Dilution Domestic energy consumption Enthalpy Fluid dynamics Gas compressor Heat pump and refrigeration cycle Heat transfer Humidity Infiltration Latent heat Noise control Outgassing Particulates Psychrometrics Sensible heat Stack effect Thermal comfort Thermal destratification Thermal mass Thermodynamics Vapour pressure of water
Technology	Absorption refrigerator Air barrier Air conditioning Antifreeze Automobile air conditioning Autonomous building Building insulation materials Central heating Central solar heating Chilled beam Chilled water Constant air volume (CAV) Coolant Dedicated outdoor air system (DOAS) Deep water source cooling Demand-controlled ventilation (DCV) Displacement ventilation District cooling District heating Electric heating Energy recovery ventilation (ERV) Firestop Forced-air Forced-air gas Free cooling Heat recovery ventilation (HRV) Hybrid heat Hydronics HVAC Ice storage air conditioning Kitchen ventilation Mixed-mode ventilation Microgeneration Natural ventilation Passive cooling Passive house Radiant heating and cooling system Radiant cooling Radiant heating Radon mitigation Refrigeration Renewable heat Room air distribution Solar air heat Solar combisystem Solar cooling Solar heating Thermal insulation Underfloor air distribution Underfloor heating Vapor barrier Vapor-compression refrigeration (VCRS) Variable air volume (VAV) Variable refrigerant flow (VRF) Ventilation
Components	Air conditioner inverter Air door Air filter Air handler Air ionizer Air-mixing plenum Air purifier Air source heat pumps Automatic balancing valve Back boiler Barrier pipe Blast damper Boiler Centrifugal fan Ceramic heater Chiller Condensate pump Condenser Condensing boiler Convection heater Compressor Cooling tower Damper Dehumidifier Duct Economizer Electrostatic precipitator Evaporative cooler Evaporator Exhaust hood Expansion tank Fan coil unit Fan filter unit Fan heater Fire damper Fireplace Fireplace insert Freeze stat Flue Freon Fume hood Furnace Furnace room Gas compressor Gas heater Gasoline heater Geothermal heat pump Grease duct Grille Ground-coupled heat exchanger Heat exchanger Heat pipe Heat pump Heating film Heating system High efficiency glandless circulating pump High-efficiency particulate air (HEPA) High pressure cut off switch Humidifier Infrared heater Inverter compressor Kerosene heater Louver Mechanical fan Mechanical room Oil heater Packaged terminal air conditioner Plenum space Pressurisation ductwork Process duct work Radiator Radiator reflector Recuperator Refrigerant Register Reversing valve Run-around coil Scroll compressor Solar chimney Solar-assisted heat pump Space heater Smoke exhaust ductwork Thermal expansion valve Thermal wheel Thermosiphon Thermostatic radiator valve Trickle vent Trombe wall Turning vanes Ultra-low particulate air (ULPA) Whole-house fan Windcatcher Wood-burning stove
Measurement and control	Air flow meter Aquastat BACnet Blower door Building automation Carbon dioxide sensor Clean Air Delivery Rate (CADR) Gas sensor Home energy monitor Humidistat HVAC control system Intelligent buildings LonWorks Minimum efficiency reporting value (MERV) OpenTherm Programmable communicating thermostat Programmable thermostat Psychrometrics Room temperature Smart thermostat Thermostat Thermostatic radiator valve
Professions, trades, and services	Architectural acoustics Architectural engineering Architectural technologist Building services engineering Building information modeling (BIM) Deep energy retrofit Duct leakage testing Environmental engineering Hydronic balancing Kitchen exhaust cleaning Mechanical engineering Mechanical, electrical, and plumbing Mold growth, assessment, and remediation Refrigerant reclamation Testing, adjusting, balancing
Industry organizations	ACCA AHRI AMCA ASHRAE ASTM International BRE BSRIA CIBSE Institute of Refrigeration IIR LEED SMACNA
Health and safety	Indoor air quality (IAQ) Passive smoking Sick building syndrome (SBS) Volatile organic compound (VOC)
See also	ASHRAE Handbook Building science Fireproofing Glossary of HVAC terms World Refrigeration Day Template:Home automation Template:Solar energy

Enthalpy

History

Formal definition

Other expressions

Cardinal functions

Physical interpretation

Relationship to heat

Applications

Heat of reaction

Specific enthalpy

Enthalpy changes

Open systems

Diagrams

Some basic applications

Throttling

Compressors

See also

Notes

References

Bibliography

External links