Juno I

Juno I

Juno I satellite launch vehicle carrying Explorer 2. (USAF)
Function	Orbital launch vehicle
Manufacturer	Chrysler for the ABMA
Country of origin	United States
Size
Height	21.2 m (70 ft)
Diameter	1.78 m (5 ft 10 in)
Mass	29,060 kg (64,070 lb)
Stages	4
Capacity
Payload to LEO	11 kg (24 lb)
Launch history
Status	Retired
Launch sites	LC-5 and 26A, Cape Canaveral Missile Annex, Florida
Total launches	6
Successes	3
Failures	3
First flight	January 31, 1958 (First orbit: Explorer 1 January 31, 1958)
Last flight	October 23, 1959
First stage - Redstone (stretched)
Engines	1x Rocketdyne A-7
Thrust	42,439 kgf (416.18 kN; 93,560 lbf)
Specific impulse	235 sec
Burn time	155 seconds
Fuel	Hydyne/LOX
Second stage Baby Sergeant cluster
Engines	11 Solid
Thrust	7,480 kgf (73.4 kN; 16,500 lbf)
Specific impulse	214 sec
Burn time	6 seconds
Fuel	Solid - polysulfide-aluminum and ammonium perchlorate
Third stage - Baby Sergeant cluster
Engines	3 Solid
Thrust	2,040 kgf (20.0 kN; 4,500 lbf)
Specific impulse	214 sec
Burn time	6 seconds
Fuel	Solid - polysulfide-aluminum and ammonium perchlorate
Fourth stage - Baby Sergeant
Engines	1 Solid
Thrust	680 kgf (6.7 kN; 1,500 lbf)
Specific impulse	214 sec
Burn time	6 seconds
Fuel	Solid - polysulfide-aluminum and ammonium perchlorate

The Juno I was a four-stage American booster rocket which launched America's first satellite, Explorer 1, in 1958. A member of the Redstone rocket family, it was derived from the Jupiter-C sounding rocket. It is commonly confused with the Juno II launch vehicle, which was derived from the PGM-19 Jupiter medium-range ballistic missile.

Development

The Juno I consisted of a Jupiter-C rocket with a fourth stage mounted on top of the "tub" of the third stage, and fired after third-stage burnout to boost the payload and fourth stage to an orbital velocity of 8 kilometres per second (29,000 km/h; 18,000 mph). The tub along with the fourth stage were set spinning while the rocket was on the launch pad to provide gyroscopic force in lieu of a guidance system that would have required vanes, gimbals, or vernier motors. This multi-stage system, designed by Wernher von Braun in 1956 for his proposed Project Orbiter, obviated the need for a guidance system in the upper stages. It was the simplest method for putting a payload into orbit but having no upper-stage guidance, the payload could not achieve a precise orbit. Both the four-stage Juno I and three-stage Jupiter-C launch vehicles were the same height (21.2 meters), with the added fourth-stage booster of the Juno I being enclosed inside the nose cone of the third stage.

The rocket family is named for the Roman goddess and queen of the gods Juno for its position as the satellite-launching version of the Jupiter-C. The name was proposed by JPL Director Dr. William Pickering in November 1957. The September 1956 test launch of a Jupiter-C for the Army Ballistic Missile Agency could have been the world's first satellite launch. Had a fourth stage been loaded and fueled, the nose cone would have overshot the target and entered orbit. Such a launch did not occur until early 1958 when a Juno 1 successfully launched the first United States satellite, Explorer 1, as part of Project Vanguard, after the Soviet Union's Sputnik 1 in October 1957.^[1]

Launch history

Although Juno I's launch of the Explorer 1 satellite was a huge success for the U.S. space program, only two of its remaining five flights were successful; launching Explorer 3 and 4. The American public was happy and relieved that America had finally managed to launch a satellite after the launch failures in the Vanguard and Viking series. With the relative success of the Juno I program, von Braun developed the Juno II, using a PGM-19 Jupiter first stage, rather than a Redstone.

Gallery

Juno I carrying Explorer 3

Juno I with Explorer I mock-up at the Kennedy Space Center rocket garden

References

• Source: Data Sheet, Department of Astronautics, National Air and Space Museum, Smithsonian Institution.