One-repetition maximum

One-repetition maximum (one rep maximum or 1RM) in weight training is the maximum amount of weight that a person can possibly lift for one repetition. It may also be considered as the maximum amount of force that can be generated in one maximal contraction.^[1] One repetition maximum can be used for determining an individual's maximum strength and is the method for determining the winner in events such as powerlifting and weightlifting competitions. One repetition maximum can also be used as an upper limit, in order to determine the desired "load" for an exercise (as a percentage of the 1RM).

Calculating 1RM

1RM can either be calculated directly using maximal testing or indirectly using submaximal estimation. The submaximal estimation method is preferred as it is safer, quicker, and less unnerving for inexperienced exercisers;^[2] however, it may underestimate the actual 1RM.^[3] One rep maximum calculators are used to predict a one rep maximum lift. The degree of accuracy can vary largely depending on the weight training experience and muscular composition of the athlete. Also, most one rep maximum calculators are designed for seasoned strength trainers, and those with little experience may find their actual one rep maximum is much lower because their nervous system cannot handle the stress of a high weight. This test should be performed with a spotter for reasons of safety.

Weight training protocols often use 1RM when programming to ensure the exerciser reaches resistance overload, especially when the exercise objective is muscular strength, endurance or hypertrophy. By understanding the maximal potential of the muscle, it is possible to reach resistance overload by increasing the number of repetitions for an exercise.

Determining the 1 rep max can be done directly through trial and error and simply requires the exerciser to complete one full repetition with the maximum weight. There are several common formulas used to estimate 1RM using the submaximal method, the Epley and the Brzycki being the most common.^[4] In the formulas below, $r$ is the number of repetitions performed and $w$ is the amount of weight used (note that $w$ is a factor of each formula, so the unit of measurement doesn't matter).

Epley formula

1{\text{ RM}}=w\left(1+{\frac {r}{30}}\right),

assuming

r>1.

Epley, B. Poundage chart. In: Boyd Epley Workout. Lincoln, NE: Body Enterprises, 1985. p. 86.

Brzycki

This version of the one rep maximum calculation is often referred to as the Brzycki Formula after its creator, Matt Brzycki,^[5] and can be written either in terms of integers or as a decimal approximation:

1{\text{ RM}}=w\cdot {\frac {36}{37-r}}={\frac {w}{{\frac {37}{36}}-{\frac {1}{36}}r}}\approx {\frac {w}{1.0278-0.0278r}}

Formula 1 (Epley) and formula 2 (Brzycki) return identical results for 10 repetitions. However, for fewer than 10 reps, formula 1 returns a slightly higher estimated maximum. For example, if a person can lift 100 pounds on a given exercise for 10 reps, the estimated one rep max would be 133 pounds for both formulae. However, if the person were to complete only 6 reps, then formula 1 would estimate a one rep maximum of approximately 120 pounds, while formula 2 would return an estimate of approximately 116 pounds.

These types of calculations may not always produce accurate results, but can be used as starting points. The weight can then be changed as needed to perform the number of reps called for by the training protocol.

Several more complex formulae have been proposed which use different coefficients for different rep numbers and sometimes even for different exercises.^[6] Using the same notation as above,

McGlothin

1{\text{ RM}}={\frac {100w}{101.3-2.67123r}}

Lombardi

1{\text{ RM}}=wr^{0.10}

Mayhew et al.

1{\text{ RM}}={\frac {100w}{52.2+41.9e^{-0.055r}}}

O'Conner et al.

1{\text{ RM}}=w\left(1+{\frac {r}{40}}\right)

Wathan

1{\text{ RM}}={\frac {100w}{48.8+53.8e^{-0.075r}}}

References

↑ Marchese, Rosemary; Hill, Andrew (2011). The essential guide to fitness: for the fitness instructor. Sydney, NSW: Pearson Australia. p. 135. ISBN 9781442510203.
↑ Marchese, Rosemary; Hill, Andrew (2011). The essential guide to fitness: for the fitness instructor. Sydney, NSW: Pearson Australia. pp. 158–159. ISBN 9781442510203.
↑ Knutzen, Kathleen; Brilla, Lorraine; Caine, Dennis (August 1999). "Validity of 1RM Prediction Equations for Older Adults". The Journal of Strength & Conditioning Research. p. Vol 13, Issue 3, Page 242–246. Retrieved 11 July 2014.
↑ Calculate your One Rep Max (1RM).
↑ Brzycki, Matt (1998). A Practical Approach To Strength Training. McGraw-Hill. ISBN 1-57028-018-5.
↑ LeSuer, Dale A.; McCormick, James H.; Mayhew, Jerry L.; Wasserstein, Ronald L.; Arnold, Michael D. (November 1997). "The Accuracy of Prediction Equations for Estimating 1-RM Performance in the Bench Press, Squat, and Deadlift". Journal of Strength and Conditioning Research. 11 (4): 211–213. doi:10.1519/00124278-199711000-00001.